10mm Corner-Cutting End Mill Solid Carbide TiAlN-Coated 3-Flute Long 45° Chamfer, h6 Shank - TECWERK

Take advantage of a durable combination of solid carbide construction and TiAlN coating for extended tool life and consistent chip control; the long, three-flute design with centre cutting enables efficient roughing and finishing in a wide range of materials. Order the tool directly via Metav Werkzeuge or consult our specialists for application guidance.

TECWERK slot drill DIN 6527 L — solid carbide, TiAlN-coated, Ø 10 mm

TECWERK slot drill DIN 6527 L engineered as a long, low-vibration cutter for versatile milling tasks in steels, cast materials and non‑ferrous metals

• Solid carbide, TiAlN coating
• Three-flute, centre-cutting geometry
• Cylindrical shank Ø 10 mm, tolerance h6
• Long, low-vibration design for roughing and finishing

Consistent cutting performance for demanding production

The TECWERK slot drill DIN 6527 L combines a solid carbide body with a TiAlN-coated cutting edge to deliver reliable wear resistance and thermal stability during extended cycles. Its three-flute configuration and centre cutting capability permit controlled plunge milling and stable slotting; the result is predictable tool life and fewer unplanned tool changes. This technical combination translates into measurable productivity gains in both single‑piece and batch production where reproducible process results are required.

Dimensioned for accurate mounting and repeatable runs

A precisely ground cylindrical shank Ø 10 mm with h6 tolerance ensures secure clamping in common toolholders and collets, reducing runout and improving surface finish. The tool’s relief length of 9.5 mm and neck relief grind create clearance where needed to avoid collisions and facilitate access in recessed features. An engineered 0.2 mm chamfer on the cutting edge protects the geometry during entry, which supports vibration‑reduced machining and consistent component tolerances.

Broad material suitability reduces tool inventories

The cutter’s geometry and coating make it very well suited to a broad spectrum of materials: steel, stainless steel, cast iron, non‑ferrous metals and a variety of special alloys. The tool is optimised for both high‑feed roughing and fine finishing, so fewer dedicated cutters are required across mixed production runs. The unequal pitch reduces harmonics during milling, assisting chip evacuation and enabling efficient work in abrasive materials and aluminium alloys with silicon content.

Practical advantages on the machine shop floor

Right‑hand cutting and a long flute version support operations where deeper slotting or extended reach is necessary, while the centre‑cutting tip allows safe axial engagement. The combination of TiAlN surface treatment and a fine‑grain carbide substrate offers a balance of hardness and toughness suitable for interrupted cuts and heavy engagement. For workshops seeking a reliable all‑round cutter that simplifies process planning, this tool provides stability, repeatability and reduced downtime.

For specification advice or to secure supply from our Emmerich stock, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930

Technical data

• Article number: 2000866289NW
• SKU/UID: 2000866289NW

Facts

• Cutting edges: Z.3
• Shank diameter: Ø 10 mm
• Relief length: 9.5 mm
• Chamfer: 0.2 mm
• Shank tolerance: h6

Special features

• Solid carbide
• TiAlN-coated
• DIN 6527 L, Type N
• Centre cutting
• Three-flute geometry
• Unequal pitch for vibration reduction
• Right-hand cutting
• Neck relief grind
• Suitable for steel, stainless steel, cast iron, non‑ferrous metals and special alloys

FAQ

Which materials is this slot drill suitable for?
The TECWERK slot drill DIN 6527 L is suitable for steel, stainless steel, cast iron, non‑ferrous metals and a range of special alloys, reflecting its universal geometry and TiAlN coating.

Can the tool be used for plunge milling?
Yes, the centre-cutting geometry permits safe axial engagement, making plunge milling and slot entry possible with appropriate feeds and speeds.

What is the shank specification for clamping accuracy?
The tool features a cylindrical shank Ø 10 mm with h6 tolerance to ensure precise clamping and minimised runout.

How does the TiAlN coating benefit machining?
The TiAlN coating increases heat resistance and surface hardness, improving wear behaviour during high-temperature cuts and extending tool life in mixed‑material production.

Is this cutter suited for both roughing and finishing operations?
Yes, the long three-flute design with a low‑vibration geometry is optimised for both roughing and finishing, offering a balance of material removal rate and surface quality.

Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund