150mm Vertical Clamp M12x80 Press Spindle 4,500 N Clamping Force, 5,000 N Holding Force - Kukamet

Take advantage of a compact, galvanised vertical clamp that combines a robust M12x80 pressure spindle with a high holding force for reliable fixture security. With a maximum holding capacity of 5,000 N and a clamping force of 4,500 N, the design supports stable vertical-foot installation; order directly via Metav Werkzeuge or consult their specialists for application matching.

Kukamet Vertical Clamp 212 — galvanised vertical clamp with M12x80 spindle

The Kukamet Vertical Clamp 212 is a compact vertical clamping device engineered for secure workpiece retention in workshop fixtures and light industrial jigs.

• Galvanised finish for corrosion resistance
• M12x80 pressure spindle for robust clamping
• Vertical-foot mounting for stable installation
• Max holding force 5,000 N, clamping force 4,500 N

Consistent clamping performance for production demands

Built around a precision M12x80 pressure spindle, this vertical clamping device delivers repeatable clamping force and consistent engagement under cycle use. The specified maximum holding force of 5,000 N and clamping force of 4,500 N give a verifiable performance envelope for fixture design and load calculations. Engineers and workshop planners can therefore integrate this clamp into predictable assemblies where known force values are required to secure workpieces during machining, inspection or assembly operations.

Compact installation that saves fixture space

With a vertical-foot mounting, the clamp preserves table and fixture real estate while offering a secure anchor point for vertical clamping tasks. The vertical-foot mounting reduces lateral footprint and simplifies alignment in jigs and modular fixtures. At approximately 1.54 kg, the unit contributes little mass to the setup, easing handling and positioning during assembly without compromising stability. The compact footprint supports denser fixture layouts and faster changeovers in small-batch production.

Galvanised finish and low-maintenance operation

A galvanised finish provides effective surface protection against corrosion in workshop environments, reducing the need for frequent upkeep and extending service life. The straightforward mechanical design minimises parts subject to wear, which translates into low maintenance and predictable downtimes. For maintenance teams, routine checks of the spindle thread and clamping surfaces are typically sufficient; spare-part complexity is minimal, which keeps workshop logistics simple and cost-effective.

Suitable uses and safe handling recommendations

This vertical clamp is particularly suitable for light to medium-duty clamping tasks in general workshop use, fixture-making and assembly stations. When specifying the clamp in a fixture, allow for the stated maximum forces (5,000 N holding, 4,500 N clamping) and ensure that mating components and fastenings meet those loads. Correct tightening of the M12x80 pressure spindle and secure fastening of the vertical foot are essential for safe operation. Where dynamic or impact loads are expected, verify application parameters against the clamp’s rated values before commissioning.

For tailored advice on integrating the Kukamet Vertical Clamp 212 (SKU 212-5) into specific fixtures or for technical matching, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss requirements and availability.

Technical Data

• SKU: 212-5
• GTIN: 8680731501766
• ETIM: EC011973
• ECLASS: 21041717
• Material: galvanised
• Weight: 1.54 kg

Facts

• Max holding force: 5,000 N
• Max clamping force: 4,500 N
• Pressure spindle: M12x80
• Weight: 1.54 kg

Special features

• Vertical clamp design
• Vertical-foot mounting
• Galvanised finish
• No special additional features

FAQ

What is the maximum holding capacity of this clamp?
The Kukamet Vertical Clamp 212 provides a maximum holding force of 5,000 N and a clamping force up to 4,500 N, values suitable for many workshop fixture applications.

Is the clamp suitable for corrosive workshop environments?
The unit features a galvanised finish, which offers good corrosion resistance and reduces maintenance frequency in typical workshop conditions.

How is the clamp mounted to a fixture?
Mounting is achieved via a vertical-foot mounting, designed for stable fastening to fixture plates or machine tables and straightforward alignment in vertical clamping setups.

Which spindle specification does the clamp use?
The clamp uses an M12x80 pressure spindle, providing robust thread engagement and straightforward replacement if needed.

Can the clamp be used in light industrial jigs and assembly stations?
Yes, the clamp is intended for workshop and light industrial fixtures where its compact footprint and rated forces meet the application requirements; verify loads against the stated maximum holding and clamping forces.

Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com