110mm Parallel Shim Set Wavy 8 Pairs 0.3mm Material Thickness, Precision Ground - AMF

Take advantage of precision-ground, hardened spring steel shims with 0.3 mm thickness and a clear 2 mm height stepping to maintain workpiece parallelism and reduce setup time; order directly via Metav Werkzeuge or contact our advisers for configuration assistance.

AMF Parallel shim set Nr. 6344SP - 9-23 (wavy profile, 110 mm)

The AMF Parallel shim set Nr. 6344SP - 9-23 is a specialised collection of precision shims designed for accurate clamping and alignment in metalworking and general workshop fixturing.

• Wavy profile prevents chips on support surface
• Precision-ground shims, thickness 0.3 mm
• Hardened and tempered spring steel
• Height increments 2 mm, pair tolerance IT5

Maintain true parallelism with fast, repeatable setups

Precision shims deliver measurable gains in setup reliability. The precision-ground surfaces and pair tolerance IT5 ensure nominal height deviations are held to ±0.004 mm, which reduces rework and inspection time. Using stepped shims streamlines the process of shimming between jaws or supports, so maintaining true parallelism of the clamped workpiece becomes a routine task rather than a daily challenge. This directly improves throughput and machining consistency.

Durable material and profile for clean contact surfaces

Built from hardened and tempered spring steel, the shims tolerate repeated clamping without deformation, extending service life and lowering replacement frequency. The wavy profile minimises contact of loose chips with the underside of the workpiece, so debris is less likely to compromise the contact surface. This leads to more consistent clamping forces and a lower risk of surface marking on delicate parts, preserving component quality during handling and machining.

Precise increments that simplify multi‑part clamping

With a 0.3 mm material thickness and 2 mm height steps, the set offers fine, graduated adjustment for stacking or combining shims to reach the required clearance. The small thickness and clear stepping make it straightforward to clamp several flat or thin components together without loss of alignment. These features reduce setup iterations and support efficient jigs and fixtures where repeatable, small adjustments are essential.

Engineered tolerances for measurement confidence

Tolerance design follows recognised standards to support predictable results: nominal height tolerance of ±0.004 mm and remaining dimensions in accordance with DIN ISO 2768m. Such specifications provide a verifiable basis for procurement decisions and quality audits, allowing the set to be integrated into measurement-controlled workflows and documented procedures with minimal additional calibration.

Contact Metav Werkzeuge for tailored advice on integrating the AMF shims into existing fixtures and order support directly from Emmerich

Technical Data

• Article number: 4000603655NW
• Type: Nr. 6344SP - 9-23
• Product: Parallel shim set
• Brand: AMF
• Content: 8 pairs
• Length: 110 mm

Facts

• Material thickness: 0.3 mm
• Height step: 2 mm
• Pair tolerance: tp in height IT 5
• Nominal height tolerance: ±0.004 mm
• Length: 110 mm
• Set content: 8 pairs

Special features

• Wavy profile to reduce chip retention
• Precision-ground surfaces
• Hardened and tempered spring steel
• Remaining dimensions per DIN ISO 2768m
• Advantage: no chips remain on support surface
• Preserves parallelism of clamped workpiece
• Enables clamping of several thin or flat workpieces

FAQ

What material are the shims made of?
The shims are manufactured from hardened and tempered spring steel, which gives the AMF shim set good wear resistance and spring characteristics suited to repeated clamping.

How fine are the height increments?
Height increments are 2 mm per step; combined with the 0.3 mm thickness of each shim, this allows precise stacking and fine adjustment when setting up fixtures.

What tolerances can be expected for height?
Nominal height tolerance is ±0.004 mm and pair tolerance is specified as IT5, ensuring consistent, repeatable height control for precision applications.

Can these shims prevent chips from affecting the clamping surface?
Yes, the wavy profile reduces chip retention on the support surface, helping to maintain clean contact and consistent clamping pressure.

Is this set suitable for clamping multiple thin workpieces?
The design and fine thickness make the set suitable for clamping several flat or thin components without compromising parallelism.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com