240g Precision Caliper Scale, 0.001g Readability, Stainless Steel Pan, DMS Sensor, IoT-Ready, Ring Windshield - KERN

Take advantage of a draft shield that improves weighing consistency and offers effortless access: the combination of three sliding doors and precise compatibility with KERN precision balances ensures stable results and smooth workflow. Order the Large Glass Draft Shield directly via Metav Werkzeuge or ask our consultants for compatibility advice and fast dispatch. Large Glass Draft Shield 572-A05 — KERN accessory with three sliding doors for easy sample access Large Glass Draft Shield 572-A05 is a glass enclosure designed to shield weighing pan assemblies from air currents while allowing convenient handling through its sliding doors. Three sliding doors for easy access Compatible with KERN 572, PKP and PKT Ø106 mm Reduces influence of drafts for stable weighing Lightweight at 0.5 kg for easy handling Consistent results through effective draught protection A well‑designed draft shield is essential for achieving reproducible readings on high‑precision balances. The enclosure reduces air disturbances that can cause fluctuation during measurement, supporting stable weighing and more reliable data logging. Its dimensions (150 x 140 x 130 mm) ensure adequate enclosure volume for common samples while keeping the disturbance zone small, which is particularly beneficial when working with analytical or precision balances. Compatibility with the specified KERN models means the shield integrates into existing measuring routines without altering calibration procedures, helping to maintain traceability and measurement confidence. Faster handling with three sliding doors Access to the weighing pan is simplified by the three sliding doors, which permit quick placement and removal of samples from multiple sides without lifting the entire enclosure. This design reduces handling time and the risk of introducing additional air movement during sample transfer, improving throughput in busy laboratory or workshop environments. The compact footprint and lightweight construction (0.5 kg) allow easy positioning and temporary removal when necessary, supporting flexible workflows where the enclosure is shared between stations or needs frequent repositioning. Practical compatibility and straightforward maintenance The shield is tailored for balance platforms with a pan diameter of Ø106 mm, fitting KERN 572 series and compatible PKP and PKT models that use that pan size. Installation is deliberately uncomplicated: the enclosure mounts around the weighing area to preserve the original balance geometry and does not require modification of the instrument. Cleaning is straightforward thanks to the glass surfaces, which maintain visual contact with the pan and sample throughout the weighing process; regular, gentle cleaning preserves visibility and prevents contamination. Overall, the enclosure offers a pragmatic balance of accessibility, protection and integration for professional measurement tasks. Contact Metav Werkzeuge for compatibility checks and fast dispatch from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 572-A05 SKU: 572-A05 GTIN: 4045761076587 Manufacturer: KERN Country of origin: DE Customs tariff number: 90160090 ECLASS: 22330605 Core specifications Dimensions: 150 x 140 x 130 mm Weight: 0.5 kg Special features Three sliding doors for convenient access Fits precision balances with weighing pan Ø106 mm Designed as a large glass draft shield for stable measurements FAQ Is this enclosure compatible with KERN analytical balances? The Large Glass Draft Shield 572-A05 is compatible with KERN 572 series and with KERN PKP and PKT models that use a weighing pan of Ø106 mm. Can the glass shield be used with larger pans? The enclosure is designed for pans with Ø106 mm and may not fit larger pan sizes; for other pan diameters an alternative enclosure is required. How does the draft shield affect measurement stability? By limiting air currents around the weighing pan, the draft shield reduces fluctuations and supports stable weighing, improving repeatability for small or lightweight samples. Is the enclosure easy to clean and maintain? Yes. The glass surfaces allow clear visibility and can be cleaned with suitable non‑abrasive agents to avoid scratches and contamination. Does the product include mounting hardware? The Large Glass Draft Shield 572-A05 is supplied as the enclosure unit; check the balance model compatibility (Ø106 mm) before integration with the instrument KERN — Germany; Contact: not specified

Take advantage of rapid visual decision-making with the combination of a 3‑colour LED and RS‑232 power connection, ensuring consistent tolerance checks and seamless integration with existing KERN scales; order the device directly via Metav Werkzeuge or consult our specialists for compatibility advice. KERN CFS-A03 signal lamp — 3‑colour LED, RS‑232 powered (KERN) The KERN CFS-A03 is a compact signal lamp designed for optical support of weighings within tolerance ranges, intended for use alongside KERN scale series in industrial and laboratory environments 3‑colour LED: red, green and yellow Powered via RS‑232 interface Compatible with multiple KERN scale series Interface cable sold separately Faster decisions through clear visual signalling The integrated 3‑colour LED provides immediate visual feedback for out-of-tolerance, within-tolerance and over-limit conditions, enabling faster sorting and fewer stoppages on production lines. As an indicator light for weighing stations, the device reduces reliance on continuous manual checks by offering clear status information at a glance. This reliability supports throughput efficiency and helps maintain consistent quality control without adding complexity to existing routines. Seamless integration with existing scale systems Designed for straightforward connection, the unit receives power and control signals via RS‑232, allowing direct interaction with a wide range of KERN scales. This method keeps wiring compact and centralises signal handling at the scale interface. Compatibility with multiple KERN series ensures flexible deployment across workbenches and packing lines, while the note that the interface cable is sold separately clarifies procurement requirements before installation. Compact, robust design for continuous operation With a compact footprint and modest mass, the lamp fits into tight production environments and mounting arrangements without obstructing workflows. The low-maintenance LED technology offers long service life and consistent luminosity, reducing downtime and replacement frequency. The unit’s role as a dedicated optical support tool helps streamline operator tasks and improves traceability of batch sorting decisions on automated or semi-automated weighing stations. For customised advice on integrating the KERN CFS-A03 into existing systems or to confirm series compatibility, contact Metav Werkzeuge — experts in precision tools and storable supply from Emmerich; our consultants can advise on the required interface cable and delivery options via info@metav-werkzeuge.com or by phone. Technical data Article number: CFS-A03 Manufacturer: KERN GTIN: 4045761133471 Country of origin: CN Facts Dimensions: 100x180x300 mm Weight: 1.04 kg Tariff number: 84239010 eClass: 27110631 ETIM: EC000399 Special features 3‑colour LED: red, green and yellow Powered via RS‑232 by the scale Compatible with KERN series BFB, BFN, BID, CKE, CPB‑N, GAB‑N, GAB‑P, IFB, IFS, IOC, KFB‑TM, KFN‑TM, KIB‑TM, NBB, NFB, NFN, SFB, UFA, UFB, UFC, UFN Interface cable not included FAQ What does the three‑colour LED indicate? The three‑colour system shows under, within and over tolerance states to simplify sorting and visual quality checks for the KERN CFS-A03 signal lamp. How is the lamp powered and controlled? Power and control signals are provided via the scale’s RS‑232 interface; the CFS-A03 relies on the connected scale for operation. Is a connecting cable included with the unit? No, the interface cable for the scale is not included; the necessary cable must be ordered separately according to the scale model. Which scales are compatible with this signal lamp? The lamp is compatible with a broad range of KERN scale series (listed in the technical data) and is intended to integrate directly into existing weighing setups. Can the lamp improve production throughput? By providing clear, immediate visual feedback on tolerance status, the indicator light reduces manual checks and supports faster, more consistent decision-making on the line. Manufacturer: KERN; Address: —; Contact: —

The combination of OIML Class F1 accuracy, a 1 g nominal mass and a polished stainless steel surface ensures traceable, repeatable results in verification tasks. Choose this single calibration weight for consistent scale checks and straightforward handling — order the KERN 326-01 directly via Metav Werkzeuge or consult our advisors if required. KERN 326-01 Calibration weight — 1 g, OIML Class F1, polished stainless steel A precision single calibration weight KERN 326-01 for laboratory and workshop scale verification, supplied in an ergonomic Eco‑Form for safe handling and reliable routine checks. OIML Class F1 accuracy Nominal mass 1 g Polished stainless steel surface Eco‑Form for ergonomic handling Precision that fits laboratory routines The KERN 326-01 delivers OIML Class F1 conformity with a tolerance of 0.1 mg, providing a high level of metrological reliability for verification and routine checks of analytical and precision balances. The small 1 g mass and compact dimensions make it suitable for frequent use where tight tolerances matter; the class designation indicates suitability for laboratory and calibration tasks that require consistent repeatability. Technical terms: OIML Class F1 denotes an internationally recognised tolerance band for test weights used in calibration and verification. Designed for safe handling and clear traceability Shaped in an Eco‑Form, the mass is easier to lift and position without compromising contact points on the balance pan, reducing handling error during routine procedures. The polished stainless steel finish improves resistance to corrosion and simplifies cleaning, supporting long service life in workshop and lab environments. Traceability is supported by adherence to OIML classification, enabling integration into regular quality workflows and documentation practices. Built for durability and straightforward integration Constructed from polished stainless steel, this single weight resists surface degradation and preserves its nominal value under normal handling conditions, lowering the need for frequent replacement. The compact design and clear classification make integration into existing verification schedules uncomplicated, supporting efficiency and compliance in environments where reliable mass standards are essential. For reliable OIML Class F1 verification with a compact single weight, contact Metav Werkzeuge in Emmerich for tailored supply and delivery details — eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 Technical data Article number: 326 SKU: 326-01 Manufacturer: KERN GTIN: 4045761223745 Eclass: 32120103 Customs tariff number: 84239090 Origin country: Germany Core technical data Nominal mass: 1 g Tolerance (OIML F1): 0.1 mg Materials & features Material: polished stainless steel Form: Eco‑Form OIML class: F1 Cylinder dimensions: 6×6 mm FAQ What level of accuracy does this calibration weight provide? The KERN 326-01 calibration weight (single weight, SKU 326-01) conforms to OIML Class F1 with a tolerance of 0.1 mg, making it suitable for precise verification tasks. Is the KERN 326-01 suitable for laboratory balances? Yes, the KERN 326-01 is designed for verification of analytical and precision balances where OIML Class F1 accuracy is required. What material is used and how does it affect maintenance? The weight is made of polished stainless steel; this finish reduces corrosion risk and simplifies cleaning for durable service life. How does the Eco‑Form shape benefit routine checks? The Eco‑Form provides an ergonomic grip that reduces handling errors and contact with balance surfaces, improving consistency during repeated measurements. Does the data include origin and classification details for documentation? The KERN 326-01 includes an OIML class designation (F1) and origin information (Germany) suitable for inclusion in verification documentation and traceability records. KERN — Origin: Germany. Manufacturer address and contact not specified.

Take advantage of fast, reliable printing together with plain‑paper archiving and an automatic cutter for streamlined weighing documentation; order the unit directly via Metav Werkzeuge or consult our specialists for integration advice. YKG-01 dot‑matrix printer by KERN — 4.7 lines/s, automatic cutter The YKG-01 is a compact dot‑matrix printer for retail, hospitality and kitchen environments, designed to print weighing results on plain paper for reliable, long‑term archiving. Fast dot‑matrix print at 4.7 lines/s Prints weighing values on plain paper Built‑in automatic paper cutter Interchangeable interface, cable not included Dependable output for retail and catering operations The unit delivers consistent impact printing that is optimised for the frequent, short receipts typical in shops and kitchens. With a rated speed of 4.7 lines/s and a maximum of 42 characters per line, the mechanism ensures legible, evenly spaced output that suits both immediate transaction needs and longer‑term record keeping. Using plain paper instead of thermal rolls reduces running costs and enables simple archival procedures, while the printer’s robust construction resists the knocks and humidity common in catering environments. Simple integration and low‑effort maintenance Engineered for straightforward connection in point‑of‑sale setups, the model provides an interchangeable interface to match existing systems; note that the interface cable is not included. The supplied EU power adapter supports 230 V AC, 50 Hz supplies, and the plug‑in power design keeps replacement simple. Routine consumable changes are fast: the design allows easy paper and ribbon replacement without specialised tools, reducing downtime and keeping staff focused on service rather than maintenance. Archive‑ready receipts and controlled operating range Because the printer produces records on plain paper, documents withstand longer storage and are compatible with conventional filing systems. The integrated automatic paper cutter gives a clean finish to each slip, improving handling and reducing errors when collecting multiple receipts. For reliable use, the device is specified for operation between 5 °C and 35 °C, and its compact footprint suits busy counters and compact kitchen stations, contributing to an orderly, compliant documentation workflow. Contact Metav Werkzeuge for an expert recommendation on integrating the KERN YKG‑01 into the workflow and to arrange supply directly from our Emmerich warehouse – eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: YKG SKU: YKG-01 Manufacturer: KERN Origin: JP GTIN: 4045761253056 Facts Dimensions: 160 x 248 x 139 mm Weight: 2.71 kg Print speed: 4.7 lines/s Max characters per line: 42 Power input: 230 V AC, 50 Hz Paper widths: 58, 70, 76 mm Operating temperature: 5 °C–35 °C Special features Printing method: impact (dot‑matrix) Power supply: EURO plug‑in adapter Built‑in automatic paper cutter Interchangeable interface (cable not included) Designed for plain‑paper receipt archiving FAQ How does the YKG‑01 handle receipt archiving? The KERN YKG‑01 prints on plain paper, producing durable receipts suitable for standard filing and longer retention periods. Is an interface cable included with the printer? No, the printer is supplied with an interchangeable interface but the interface cable is not included and must be provided separately. What power supply is required for the unit? The unit uses a 230 V AC, 50 Hz supply and is shipped with a EURO plug‑in adapter. Can the printer be used in a kitchen environment? Yes, the design and impact printing method make it suitable for retail and catering settings; operating conditions should remain within 5 °C–35 °C. What makes this model suitable for point‑of‑sale systems? Its compact size, fast 4.7 lines/s output, automatic paper cutter and interchangeable interface facilitate simple integration into POS workflows. Metav Werkzeuge — Emmerich (warehouse and quality hub); Contact: info@metav-werkzeuge.com; Tel: +49 2822 7131930; WhatsApp: +49 170 2837271

Die Antivibrationsplatten KERN YPS-04, -05, -06 sind dafür konstruiert, Erschütterungen und Schwingungen zu dämpfen, die sonst das Wägeergebnis von hochpräzisen Präzisions- und Analysenwaagen verfälschen würden. Ideal auch zum vibrationsfreien Aufstellen von Mikroskopen geeignet Die Antivibrationsplatte besteht aus poliertem Granit, die auf absorbierenden Gummielementen gelagert sind An der Antivibrationsplatte kann ergonomisch optimiert im Stehen oder bequem im Sitzen gearbeitet werden Kompakte Abmessungen, vorteilhaft bei eingeschränkten Platzverhältnissen Alle Oberflächen sind hygienisch und leicht zu reinigen Passend für alle KERN Analysenwaagen, Präzisionswaagen und Mikroskope mit den entsprechenden Abmessungen Nettogewicht ca.: YPS-04: 30 kg YPS-05: 35 kg YPS-06: auf Anfrage Versandbereit in 2 Tagen. Versand komplett auf Palette. Maße, Bruttogewicht, Versandkosten bitte anfragen