SNGN 120424 FX105 Wendeplatten - Tungaloy

Take advantage of a tried-and-tested carbide grade for dependable tool life, combined with ISO‑standard geometry and straightforward compatibility with established holder systems — order directly via Metav Werkzeuge or consult our specialists for application-specific advice.

SNGN120424 FX105 SNGN — Turning insert, 2.4 mm corner radius, Tungaloy

A SNGN120424 FX105 Tungaloy indexable insert engineered for precise external and internal turning in ISO systems.

• ISO-standard indexable insert for turning
• Tungaloy FX105 carbide grade for durability
• 2.4 mm corner radius for secure edge strength
• Square 12 mm plate with 0° relief angle

Longer tool life through balanced grade properties

The FX105 designation identifies a Tungaloy carbide grade developed to balance wear resistance and edge stability, which results in more predictable performance across a range of turning tasks. That balance reduces unplanned tool changes and supports a steadier surface finish over longer runs, delivering measurable efficiency gains in batch and continuous production. The result is a lower overall tooling cost per component through fewer interventions and consistent cycle times.

Simple integration with ISO holder systems

This insert conforms to the ISO series of turning plates; compatibility is ensured by matching form, relief angle, tolerance class, fastening and thickness to the toolholder. Typical system setup comprises the insert, the matching holder, a shim or clamping set and replacement screws, allowing rapid exchange and repeatable seating. Clear geometry and the standardised interface make it straightforward to fit the plate into existing tool chains, minimising set-up time.

Designed for turning applications where edge security matters

Intended for both external and internal turning, the plate’s square form and pronounced corner radius provide robust cutting edges suited to interrupted cuts and general turning operations. The specified 2.4 mm corner radius increases edge strength and reduces risk of chipping at the corner, while the 0° relief angle supports a neutral cutting action that can be advantageous on a wide variety of component shapes when the correct chipbreaker and cutting data are selected.

Practical handling and selection advice for machinists

The plate’s dimensions — 12 mm insert size and 4.76 mm thickness — combined with the standardised ISO geometry permit easy indexing and accurate repeatability after each seat change. For best results, pair the insert with a holder matching the plate thickness and tolerance class and choose a chipbreaker or substitute geometry suited to the workpiece material and stability of the set-up. For application advice or to verify suitability for a particular operation, technical consultation is available to support selection and cutting-parameter decisions.

For reliable, productive turning with the Tungaloy FX105 grade, contact Metav Werkzeuge for tailored advice and rapid supply: Metav Werkzeuge can assist with holder matching, cutting data and order placement.

Technical Data

• Article number: 6806575
• Manufacturer SKU: TUN6806575
• Model series: ISO‑Drehwendeschneidplatten
• Designation: SNGN120424 FX105
• Material: Hartmetall (carbide)

Facts

• Corner radius: 2.4 mm
• Plate size: 12 mm
• Plate thickness: 4.76 mm
• Relief angle: 0°
• Included angle: 90°

Special features

• ISO‑standard indexable insert for turning
• FX105 Tungaloy carbide grade
• Square plate form
• No hole
• No chipbreaker supplied
• Compatibility determined by form, relief angle, tolerance, fastening and thickness
• System components: holder, shim/clamp set, spare screws

FAQ

What operations is the SNGN120424 FX105 suited to? The SNGN120424 FX105 Tungaloy insert is designed for external and internal turning operations within ISO toolholder systems.

How does the FX105 grade affect tool life? The FX105 grade from Tungaloy provides a balance of wear resistance and edge stability, which supports extended tool life and consistent component quality under stable cutting conditions.

Which dimensions are critical when matching a holder? Key dimensions include the plate thickness (4.76 mm), plate size (12 mm) and the relief angle (0°); these must match the holder’s seat and tolerance class for secure clamping.

Is a chipbreaker included with the plate? This indexable plate is supplied without a chipbreaker; the appropriate chip control solution should be selected according to material and machining strategy.

Can this insert be indexed after wear? Yes, the square geometry allows multiple index positions; the 2.4 mm corner radius provides robust edge strength across successive indexes.

Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.