SPGN 090308 TH10 Wendeplatten - Tungaloy

Take advantage of the combination of a sharp TH10 grade, the multidirectional AddMultiTurn system and a compact square geometry for efficient turning operations; order the insert directly via Metav Werkzeuge or contact the consultants for application advice.

SPGN 090308 TH10 square turning insert for turning — Tungaloy

The SPGN090308 TH10 is a square indexable insert designed for multidirectional turning in the AddMultiTurn system, optimised for longitudinal turning, facing and profiling of non-ferrous materials and similar applications.

• Multidirectional AddMultiTurn compatibility
• Uncoated carbide TH10 for low cutting forces
• Square 09 size with 90° geometry
• 0.8 mm corner radius for fine finishing

Reliable performance in multidirectional turning

The AddMultiTurn platform enables multiple cutting directions with a single toolholder, delivering process stability in mixed turning tasks. The insert’s square geometry and 90° entry angle provide consistent contact conditions during longitudinal and facing operations, which reduces setup complexity. Designed for industrial production, the system construction comprises a holder, changeable inserts and a robust clamping arrangement to ensure repeatable positioning and minimal runout.

Geometry engineered for surface quality and edge strength

A 0.8 mm corner radius and a 11° relief angle balance edge strength and surface finish, permitting controlled engagement during profiling and finishing passes. The plate thickness of 3.18 mm contributes to stability under moderate to heavy cuts, while the square form offers four usable cutting edges per indexable plate. The absence of a central hole simplifies seating in clamping designs that rely on face contact and lateral fixation.

Material grade and machining suitability

The uncoated carbide grade TH10 is a sharp universal grade formulated for non-ferrous materials and situations where an uncoated cutting edge reduces cutting forces and improves surface quality. Its composition supports clean chip formation and low built-up edge risk when machining softer alloys and brass-like materials, helping to maintain consistent component aesthetics and dimensional control over series runs.

Integration and productivity advantages for shops

As a component of the AddMultiTurn concept, the insert supports fast index changes and reduced tool inventory, which contributes to lower cycle times and higher uptime. The combination of a stable cutting edge, straightforward clamping and a universal grade means fewer tool changes across varied tasks, enhancing overall machining economy while keeping process control simple and traceable.

For ordering and detailed application support for the SPGN090308 TH10 insert, contact Metav Werkzeuge for technical consultancy at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the best holder and cutting parameters for the intended turning tasks

Technical data

• Article number: 6807052
• Manufacturer SKU: TUN6807052
• Metav SKU: 6807052-Tungaloy
• Model series: AddMultiTurn

Facts

• Corner radius: 0.8 mm
• Relief angle: 11°
• Insert thickness: 3.18 mm
• Insert size: 09
• Angle: 90°

Special features

• Grade: TH10
• Material: uncoated carbide
• Insert form: square
• Hole: without hole
• Typical application: turning (longitudinal, facing, profiling)
• System components: holder, changeable inserts, clamping system
• Designation: SPGN090308

FAQ

What materials is this insert best suited for?
The SPGN090308 TH10 insert is intended primarily for non-ferrous materials and similar alloys; the uncoated TH10 grade supports low cutting forces and clean surfaces when machining these materials.

Can the insert be used for profiling as well as roughing?
Yes, the geometry and 0.8 mm corner radius permit both profiling and finishing passes; the insert’s thickness and square form provide sufficient edge stability for moderate roughing as well.

How many edges are available per insert?
With a square plate form, the insert provides four usable cutting edges; the AddMultiTurn concept and robust clamping ensure repeatable indexing.

Is a special holder required for AddMultiTurn operation?
The insert is designed for the AddMultiTurn system; holders compatible with this system are required to exploit multidirectional turning and secure the insert correctly.

Does the insert have a chipbreaker?
This designation is supplied without a dedicated chipbreaker; chip control depends on grade, cutting conditions and the chosen toolholder geometry.

Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.