TPGT 130304 TH10 Wendeplatten - Tungaloy

Take advantage of the combination of a sharp TH10 uncoated carbide grade, precise 0.4 mm corner radius and secure ISO compatibility for efficient, low-force turning of non-ferrous materials; order the TPGT130304 TH10 insert directly via Metav Werkzeuge or consult the specialists for application advice.

TPGT 130304 TH10 Triangular ISO turning insert for precision turning — Tungaloy

TPGT 130304 TH10 is an ISO‑standard triangular turning insert designed for general turning tasks, offering a sharp uncoated cutting edge and a 60° cutting geometry suitable for non‑ferrous and delicate finishing operations.

Triangular ISO insert, 60° cutting geometry
Sharp uncoated carbide grade TH10
0.4 mm corner radius for fine turning
Cylindrical hole with single‑sided countersink

Higher throughput with low cutting forces

The combination of the TH10 uncoated carbide grade and a sharp edge reduces cutting resistance, which translates into lower cutting forces and smoother chip formation during turning. For applications where material adherence or built‑up edge risk must be minimised—such as machining soft aluminium alloys or brass—the uncoated grade supports cleaner finishes and reduced secondary operations. The triangular 60° geometry enables stable cutting for both external and internal turning cycles, improving cycle times without sacrificing surface quality.

Consistent surface quality and fine detail control

A precise 0.4 mm corner radius offers a reliable compromise between edge strength and fine profile definition. This radius, together with the single‑sided chipbreaker, delivers controlled chip formation and helps maintain consistent surface roughness on workpieces. Where dimensional accuracy and aesthetic appearance matter—such as in bearing housings or decorative turned parts—the insert’s geometry helps achieve repeatable results and reduces the need for manual rework.

Secure seat and simple integration into ISO tool systems

The insert is supplied with a cylindrical hole and a single‑side countersink (40°–60°) to match common clamping systems. As an ISO‑standard insert, compatibility with holders depends on form, relief angle, tolerance class, fastening method, size and thickness; the 11° relief angle and 3.18 mm thickness are typical for stable seating in a wide range of external holders and boring bars. This standardisation simplifies tool inventory and changeover, supporting uninterrupted production and easier tool life planning.

Practical selection and machining guidance

For turning of non‑ferrous materials and situations demanding low cutting forces, select the TH10 grade and the one‑sided chipbreaker; when machining harder or coated materials, choose a different grade or coating suited to the substrate. The insert’s triangular form offers three usable cutting edges per insert, improving cost efficiency per cutting edge while maintaining precision. For optimised process results, pair the insert with the correctly sized holder and appropriate clamping set as part of a standard ISO tool system.

Contact Metav Werkzeuge for tailored application advice and secure supply of the Tungaloy TPGT130304 TH10 insert for low‑force, high‑quality turning tasks

Technical Data

• Article number: 6808944-Tungaloy
• Manufacturer SKU: TUN6808944
• Manufacturer article number: 6808944

Facts

• ISO designation: 130304
• Cutting angle: 60°
• Corner radius: 0.4 mm
• Relief/clearance angle: 11°
• Thickness: 3.18 mm
• Inscribed circle/size: 13

Special features

• Uncoated carbide grade TH10
• Triangular plate form
• One‑sided chipbreaker
• Cylindrical hole with single‑sided countersink (40°–60°)
• Suitable for external and internal turning
• Optimised for non‑ferrous materials and low cutting forces

FAQ

What materials is this insert best suited for?
The TH10 grade insert is optimised for non‑ferrous materials and applications where an uncoated edge aids in achieving low cutting forces and clean surfaces; the TPGT130304 TH10 insert from Tungaloy excels on aluminium and brass.

How does the 0.4 mm corner radius affect machining results?
A 0.4 mm corner radius balances edge strength with finish capability; it allows the insert to produce fine surface finishes while retaining enough robustness to withstand normal turning loads with the TH10 carbide.

Is the insert compatible with standard ISO holders?
Yes — as an ISO‑standard turning insert the TPGT130304 fits holders that match its form, relief angle, tolerance class, fastening method, size and thickness; ensure the holder accepts a triangular insert with a 3.18 mm thickness and the specified hole style.

How many edges are available per insert and what is the typical use case?
The triangular form provides three indexable cutting edges; this insert is typically used for general external and internal turning where low cutting forces and surface quality are priorities.

Does the insert include coating?
This product is an uncoated carbide insert (TH10), designed to perform without coating where a sharp, low‑force cutting edge improves surface finish.

Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.