355mm Circular Saw Blade 80 Teeth Microteq For Sandwich Panels 30mm Bore 2.6mm Kerf - Robert Bosch Power Tools GmbH

Take advantage of the blade’s capacity for clean, burr-free cuts in steel-faced sandwich panels and the long-wearing Microteq teeth that reduce stoppages and rework; order directly via Metav Werkzeuge or contact our consultants for specification advice and availability.

Bosch AD 355 mm circular saw blade (80 teeth, Microteq, 30 mm bore)

The Bosch AD 355 mm circular saw blade is a specialist blade for plunge and handheld circular saws, engineered to deliver precise, clean cuts in sandwich panels with single or double-sided steel facings

• Expert for sandwich panel cutting
• 355 mm diameter for deep cuts
• 80 Microteq teeth for long life

Clean, consistent cuts for composite panels

Engineered for the demands of construction and panel fabrication, this blade produces clean cuts in sandwich panels with steel facings, whether coated on one side or both. The geometry and tooth design are optimised for minimal delamination and reduced burr formation, which leads to fewer finishing steps and less material waste. Intended for use in plunge and handheld circular saws, the blade’s configuration supports steady depth control and repeatable edges, helping maintain production tolerances when machining layered composite panels with steel skins.

Longevity that improves shop throughput

Equipped with Microteq teeth, the saw blade is designed to resist wear under continuous use, extending service intervals and reducing tool-change frequency. The high tooth count and specialised tip material maintain cutting performance over longer runs, which translates into improved efficiency and lower operational interruptions. Fewer blade replacements and less downtime for regrinding or swapping tools contribute to a more predictable workflow and consistent output quality in repetitive cutting tasks.

Precision sizing for straightforward integration

Key dimensions are provided to ensure a straightforward mechanical fit: a 355 mm diameter, 30 mm bore, and a 2.6 mm kerf enable compatibility with common arbour standards and allow consideration of material removal for joint design. These specifications support accurate planning for kerf allowance and cutting clearance when integrating into existing processes or jigs. The moderate kerf balances material conservation with rigidity, delivering a stable cut even at plunge starts.

Practical benefits and safe operation

Beyond cut quality and durability, the blade supports safer, more reliable operation when used with the correct guards, riving knife or anti-kickback devices on compatible saws. Reduced need for secondary finishing decreases handling and associated safety exposure. The combination of design, tooth technology and dimensional standards is intended to provide a reliable tool for workshops and site teams who require repeatable results when processing composite panels with steel skins.

For precise sandwich-panel cutting requirements, contact Metav Werkzeuge for stock status and tailored technical guidance on the Bosch AD 355 mm circular saw blade (SKU 8000342240NW) – call or email our Emmerich team for expert recommendations

Technical data

• Article number: 8000342240NW
• Label: Kreissägeblatt AD 355mm Z.80 MTCG Bohr.30mm Schnitt-B.2,6mm BOSCH
• Manufacturer: Robert Bosch Power Tools GmbH

Facts

• Diameter: 355 mm
• Teeth: 80
• Bore: 30 mm
• Kerf (cut width): 2.6 mm

Special features

• Expert for sandwich panels for plunge and handheld circular saws
• Clean cuts in sandwich panels with steel sheets (single or double-sided coated)
• Teeth made from Microteq for high durability

FAQ

What materials is this blade intended for?
This circular saw blade is intended primarily for sandwich panels with steel facings; the Bosch AD 355 mm circular saw blade (SKU 8000342240NW) is optimised for cutting coated steel skins without excessive burrs.

Can the blade be used in a plunge saw and in handheld circular saws?
Yes, the blade is designed for use in both plunge and handheld circular saws, providing appropriate tooth geometry and balance for these machine types.

What are the bore and diameter requirements?
The blade requires a 30 mm bore and has a 355 mm diameter; ensure that the machine arbour matches the 30 mm centre or that a suitable reducer is used.

How many teeth does the blade have and what does Microteq mean?
The blade has 80 teeth; the Microteq tooth material and tip design increase wear resistance and maintain cutting performance over extended periods, reducing the frequency of replacements.

What is the kerf and how does it affect cutting?
The kerf is 2.6 mm, which provides a balance between material removal and blade stiffness—helpful for maintaining straight cuts while keeping waste to a minimum.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com