220g Precision Analytical Balance 0.0001g Readability, CAL Adjustment, 90mm Pan - KERN

Take advantage of OIML E2 accuracy and the compact, polished stainless-steel design for reliable verification of precision balances; the 200 g nominal mass with 0.3 mg tolerance ensures consistent calibration results. Order this calibration weight via Metav Werkzeuge or contact our consultants for tailored advice on accessories and storage. KERN 316-08 Calibration weight (200 g, OIML E2) The KERN 316-08 is a compact calibration weight designed for precise verification of laboratory and industrial scales, featuring a polished stainless-steel finish and OIML E2 class accuracy OIML class E2 calibration grade Nominal value 200 g, compact form Polished stainless steel construction Tolerance 0.3 mg for high precision Accuracy that supports traceable results The core benefit of this calibration mass is its certified OIML E2 accuracy, which provides a tolerance of 0.3 mg for the nominal 200 g value. This level of precision makes the weight suitable for routine verification and adjustment of high-resolution balances where tight measurement uncertainty is required. The certification backing removes guesswork from conformity checks and supports documented measurement procedures in quality-controlled environments, offering a rational, efficiency-driven advantage for metrology workflows. Compact design for controlled handling and storage A compact profile and polished stainless steel surface reduce the influence of contaminants and ease cleaning, while the cylinder dimensions of 28×43 mm ensure stable placement on balance pans with limited space. The robust finish resists corrosion and minimises maintenance, translating into fewer interruptions in calibration routines. For long-term stability, storage in a protective case is recommended to prevent abrasion and contamination, preserving the mass’s reference value between verifications. Practical suitability across labs and workshops Manufactured to exacting standards in Germany, this single calibration weight supports accurate mass comparisons and routine traceability checks in laboratories, production control and service environments. The compact form factor simplifies transport within a calibration set and the stable geometry reduces sensitivity to handling errors. By integrating such a reference mass into regular procedures, measurement reliability improves and audit readiness is strengthened, delivering both operational and compliance benefits. Contact Metav Werkzeuge in Emmerich for expert advice on the KERN 316-08 calibration weight, accessory recommendations such as protective cases, and reliable supply for workshop or laboratory needs Technical data Article number: 316 SKU: 316-08 GTIN: 4045761094901 Manufacturer: KERN Key measurements Nominal value: 200 g Mass (kg): 0.2 kg Cylinder dimensions: 28×43 mm OIML tolerance: 0.3 mg Tariff code: 84239090 Materials and features Material: polished stainless steel Form: compact form OIML class: E2 Origin: Germany Recommended accessory: protective case (etui) FAQ What is the intended use of this calibration weight? The KERN 316-08 calibration weight is intended for verification and adjustment of precision balances and scales where OIML E2 class accuracy is required. How precise is the 200 g weight? The nominal 200 g mass has an OIML E2 tolerance of 0.3 mg, ensuring high repeatability for laboratory and industrial verification tasks. Is the weight suitable for regular transport between sites? The compact form and polished stainless-steel construction make the weight suitable for transport, provided it is carried in a protective case to avoid contamination or mechanical damage. How should the weight be stored to preserve accuracy? Storage in a dedicated protective case (etui) is recommended to prevent abrasion and contamination and to maintain long-term stability of the calibration mass. Does this weight come with certification or traceability information? The OIML E2 classification indicates the weight meets internationally recognised calibration standards; specific certificates or documentation can be requested when purchasing the KERN 316-08. Metav Werkzeuge, Emmerich am Rhein, Germany — eMail: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271

Benefit from electrostatic neutralisation and a compact, adjustable design for consistent, gram‑accurate results in precision weighing; the device’s low ozone output adds safety while keeping air quality within typical laboratory tolerances. Order the ioniser directly via Metav Werkzeuge or ask our consultants for application advice. KERN YBI-01A Ioniser — neutralises electrostatic charge, low ozone emission The KERN YBI-01A ioniser is a compact device for neutralising electrostatic charge on non-conductive weighing items beside precision balances and laboratory scales, enabling more reliable milligram‑level results. Neutralises static charge for precise weighing Low ozone emission 0.05 ppm/h Compact 115 x 110 x 80 mm footprint Adjustable feet or handheld targeting Achieve repeatable, gram‑accurate weighing through targeted electrostatic neutralisation Electrostatic charge on non-conductive materials such as plastic, porcelain or glass can create an electromagnetic field between the sample and the balance, leading to measurement errors that may reach the gram scale. The ioniser removes residual charge by producing a balanced stream of positive and negative ions, allowing the balance to register the true mass without drift or attraction. This results in fewer retests, reduced sample handling and higher process throughput — a clear efficiency gain for laboratories and quality control stations that demand reproducible micro‑ and milligram results. The effect is particularly noticeable when handling light or small parts where even slight electrostatic influence can distort the outcome. Flexible positioning for bench integration and targeted use Designed for easy placement, the unit fits beside most laboratory balances thanks to its compact dimensions and low weight. It can be set on adjustable feet for stable bench mounting or used handheld to address critical points on awkwardly shaped components. The small footprint allows integration without altering the weighing workflow, and the option for targeted ionisation supports fast intervention during sample preparation. These features make it suitable for production benches, research labs and trade environments where space is limited but measurement integrity is essential. Safe, straightforward operation compatible with international mains supplies Operation is straightforward: the device runs from a plug‑in power supply that accepts 100–240 V input and is supplied with adapters for AUS, CH, EURO, UK and US sockets, ensuring compatibility in multi‑site operations. With an ozone emission of 0.05 ppm/h, the unit maintains low by‑product levels, supporting safe use in laboratory environments when normal ventilation procedures are followed. Lightweight and portable, the unit requires minimal setup and little maintenance, delivering a practical static‑control solution that complements established weighing equipment and standard operating procedures. Contact Metav Werkzeuge for tailored advice on integrating the KERN YBI-01A ioniser into existing weighing processes or to request application guidance from our specialists in Emmerich Technical data Article number: YBI-01A Manufacturer: KERN GTIN: 4045761194984 Country of origin: Italy Core specifications Dimensions: 115 x 110 x 80 mm Weight: 0.44 kg Input voltage: 100 V - 240 V Ozone emission: 0.05 ppm/h Tariff code: 90160090 Features & compatibility For non-conductive weighing items: plastic, porcelain, glass Placement: adjustable feet or handheld targeting Power supply: adapters included for AUS; CH; EURO; UK; US Power supply type: plug-in power supply eClass: 17111116 FAQ How does the ioniser prevent weighing errors caused by static charge? The device neutralises electrostatic charge by emitting a balanced flow of positive and negative ions; this reduces the electromagnetic interaction between sample and balance and stabilises readings when using the KERN YBI-01A ioniser. Can this device be used with all types of laboratory balances? Yes; the static eliminator is intended for use beside precision balances and scales, particularly where non-conductive materials are weighed and electrostatic effects are a known issue. Is the ozone emission of the unit safe for laboratory use? The ioniser has a measured ozone emission of 0.05 ppm/h, a low level suitable for normal laboratory operation when standard ventilation practices are observed. What power connections are supplied with the unit? A plug‑in power supply accepting 100–240 V is provided, together with adapters for AUS, CH, EURO, UK and US sockets to facilitate use across multiple sites. Will the unit reduce the need for re‑weighing and sample handling? By neutralising charge on light and non-conductive samples, the device reduces measurement drift and attraction errors, which in turn lowers the frequency of retests and extra handling. Manufacturer: KERN — Address: not specified — Contact: not specified

Take advantage of electrostatic neutralisation, flexible placement and seamless rear-panel integration to secure reliable milligram results and reduce reweighs. Order the unit directly via Metav Werkzeuge or contact our consultants for advice on fitting and compatibility. ABP-A01 — KERN windscreen back panel with integrated ioniser for precision balances The ABP-A01 is a windscreen back panel with an integrated ioniser that neutralises electrostatic charges during fine weighing, designed for laboratory and industrial balance applications. Neutralises electrostatic charge for precise weighing Integrated ioniser for compact rear-panel fitting Positionable with stand or handheld operation Reduces weighing errors in milligram range Achieve milligram accuracy by removing electrostatic influence Electrostatic charging on non-conductive samples creates a small electromagnetic field between the sample and the balance, which can distort results by grams or milligrams. The ABP-A01 uses a controlled ioniser function to neutralise that charge, stabilising the measurement environment and enabling precision weighing even with lightweight specimens. This direct reduction of measurement variability supports reproducible results and fewer repeat measurements, improving throughput and reducing material waste. Flexible placement that adapts to existing workflows The design allows the ioniser to be placed beside the balance using a stand or directed by hand for targeted neutralisation, giving operators flexibility during routine tasks. When ordered together with compatible models in the ABP series, professional rear-panel integration is offered to fit the unit cleanly into the balance enclosure, preserving the bench layout and minimising interference. The combination of portability and fixed integration supports a smooth workflow between bench tasks and analytical routines. Straightforward compatibility and simple function explanation Installation and operation are deliberately simple: the module neutralises charged particles near the weighing chamber so technicians need not alter weighing technique. Where rear-panel fitting is requested, the ABP-A01 is prepared for professional integration with ABP-series balances, ensuring correct alignment and electrical routing. The result is an unobtrusive addition to the setup that delivers consistent repeatability without complex adjustments. Designed for common non-conductive samples and routine use Materials such as plastic, porcelain and glass are particularly prone to electrostatic charging; the ABP-A01 is specified to address these cases and to support routine quality control and laboratory analysis. Built to be a compact and practical accessory, it complements balances used in analytical laboratories, quality departments and technical workshops where reliable low-mass measurement is essential. The accessory’s features focus on measurable benefits: fewer reweighs, clearer data and a more efficient weighing process. Contact Metav Werkzeuge in Emmerich for tailored advice on integrating the KERN ABP-A01 into existing balances — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss fitting options and supply Technical data Article number: ABP-A01 Manufacturer: KERN GTIN: 4045761213975 SKU: ABP-A01 Weight: 0.85 kg Country of origin: PH Tariff code: 90160090 Category: Waagen > Zubehör eClass: 22330605 Core specifications Weight: 0.85 kg GTIN: 4045761213975 Tariff code: 90160090 eClass: 22330605 Special features Integrated ioniser for electrostatic neutralisation Suitable for non-conductive weighing goods (plastic, porcelain, glass) Placement: stand or handheld operation Option: rear-panel fitting with ABP series balances (service integration) Rapid dispatch from webshop FAQ How does the ioniser improve weighing accuracy? The ABP-A01 neutralises electrostatic charges that create fields between non-conductive samples and the balance, reducing measurement deviation and improving stability in the milligram range. Can the ioniser be fitted to existing ABP-series balances? Yes; when ordered in combination with an ABP-series model, the ABP-A01 can be professionally integrated into the rear panel to ensure a neat fit and correct alignment. Which sample types benefit most from the ioniser? Non-conductive materials such as plastic, porcelain and glass are most affected by static charge; the ABP-A01 is specified to reduce those effects and improve repeatability. Is the unit suitable for routine quality-control weighing? The ABP-A01 provides consistent neutralisation and supports repeatable weighing procedures, making it appropriate for routine QC and analytical tasks. Manufacturer: KERN — Address: Philippines — Contact: via Metav Werkzeuge, info@metav-werkzeuge.com, +49 2822 7131930

Take advantage of reliable RS-232 data transfer and a 1.5 m cable length to integrate measurement equipment smoothly into existing workflows. Order the cable directly via Metav Werkzeuge from the Emmerich warehouse or request tailored advice from our consultants. MLB-A05 Interface Cable — RS-232 connection, 1.5 m (KERN) The MLB-A05 Interface Cable is a dedicated RS-232 connection lead for weighing instruments and laboratory balances, engineered to provide steady data transmission between measurement devices and external systems. RS-232 serial interface 1.5 m cable length Compatible with KERN balances Robust connector design Ensure accurate data logging with stable RS-232 transfer The RS-232 interface offers a proven, industry-standard method for serial data exchange, making this cable well suited to industrial metrology and laboratory environments where measurement integrity matters. By providing reliable data transfer, the cable reduces the risk of communication errors during recording and logging tasks, which in turn supports traceability and process consistency. The design supports routine integration into existing measurement setups without requiring changes to software or instrument firmware. Easy integration and clear compatibility for weighing systems With a 1.5 m lead, connection flexibility between bench instruments and nearby data terminals is increased while keeping cable routing tidy in workshop or lab setups. The cable is specified for use with RS-232-equipped devices commonly found on balances and related instruments, ensuring broad compatibility across models. Installation is straightforward: the interface lead serves as a direct conduit for serial signals, simplifying set-up procedures and reducing the need for adapters or converters in typical measurement environments. Built for dependable workshop and laboratory use The cable’s construction balances a robust connector with low weight, enabling frequent handling and routine use at weighing stations without imposing undue strain on instrument ports. The modest mass supports neat cable management and minimises mechanical load on connectors during daily operation. Sourced under the KERN product line, the accessory is intended to complement precision equipment with components that preserve uptime and support consistent measurement workflows. For reliable serial connectivity choose the KERN MLB-A05 interface cable—contact Metav Werkzeuge in Emmerich for specialist guidance or to order directly from our stock. Technical data Article number: MLB-A05 Manufacturer: KERN SKU: MLB-A05 GTIN: 4045761245204 Core data Cable length: 1.5 m Weight: 0.08 kg ECLASS: 19050112 Tariff code: 84239010 Special features Interface: RS-232 Category: Accessories for scales Origin: China FAQ What interface does this cable use? The MLB-A05 interface cable uses the RS-232 serial interface for data transfer between balances and external devices. Is the cable compatible with KERN scales? Yes, the lead is specified for compatibility with KERN weighing instruments and other devices that provide an RS-232 port. How long is the cable and how heavy is it? The cable measures 1.5 m in length and has a weight of 0.08 kg, suitable for bench-top and near-equipment routing. Can this cable be used for data logging to a PC or printer? The MLB-A05 is designed for RS-232 connections and can be used to link RS-232-capable instruments to serial printers or data acquisition systems that accept serial input. Metav Werkzeuge, Emmerich am Rhein, info@metav-werkzeuge.com, +49 2822 7131930

Take advantage of precise measurement results through robust vibration damping and a heavy, polished granite surface that stabilises sensitive instruments; compact dimensions and hygienic surfaces support ergonomic use in space-constrained labs. Order the antivibration plate directly via Metav Werkzeuge or contact our consultants for tailored advice and fast dispatch. KERN YPS-05 Antivibration Plate — Polished granite, 565×450×60 mm The KERN YPS-05 is an antivibration plate designed to isolate analytical balances and microscopes from vibrations, providing a stable working surface for high-precision measurements Polished granite on resilient rubber supports Suitable for analytical balances and microscopes Compact footprint 565×450×60 mm Hygiene-friendly, easy-to-clean surfaces Reduce measurement errors with a stable work surface High-precision weighing and optical inspection require a stable base to prevent fluctuating results. The KERN YPS-05 combines mass and material to provide effective vibration damping: the dense polished granite top increases inertia, while the support system attenuates external shocks. This construction reduces measurement scatter and the need for repeat tests, which improves throughput and ensures repeatable results for both routine and traceable analytical tasks. The described behaviour of the platform is particularly relevant when using analytical balances, where even small vibrations can affect the displayed value. Compact footprint that supports ergonomic workflows A small laboratory bench or a crowded workshop does not need to compromise on measurement quality. With overall dimensions of 565×450×60 mm, the plate fits tight workspaces while allowing ergonomic operation either standing or seated. The top surface is finished for cleanliness: hygienic surfaces are easy to wipe down and maintain, supporting contamination control in sensitive environments. The low-profile design enables comfortable access to instruments and ancillary equipment and is tailored to accommodate KERN precision instruments and microscopes with corresponding base sizes. Robust build and ready logistics for uninterrupted operation Durability is central to a long service life and consistent performance. The YPS-05 rests on absorbing rubber elements that decouple the granite slab from bench vibrations and protect the platform from transmitted shocks. This arrangement creates a dependable working surface that preserves instrument calibration and extends operational uptime. For operational planning, the unit is shipping ready in 2 days and delivered palletised, reducing lead times and simplifying installation. The combination of a heavy top and resilient supports yields a stable base that lowers the frequency of adjustments and supports efficient lab routines. For reliable vibration control choose the KERN YPS-05 and contact Metav Werkzeuge in Emmerich for expert advice and prompt palletised dispatch Technical Data Article number: YPS-05 SKU: YPS-05 Manufacturer: KERN GTIN: 4045761253568 Dimensions: 565×450×60 mm Material: Polished granite Origin: DE Commodity code: 84239010 ECLASS: 21170605 Facts Dimensions: 565×450×60 mm Net weight: approx. 42 kg Shipping: ready in 2 days Commodity code: 84239010 ECLASS: 21170605 Special features Material: polished granite Mounted on absorbing rubber elements Hygienic, easy-to-clean surfaces Ergonomic use standing or sitting Suitable for KERN analytical and precision balances and microscopes with corresponding dimensions Shipping: palletised FAQ Is the antivibration plate compatible with analytical balances? The KERN YPS-05 antivibration plate is designed for use with KERN analytical balances and precision scales that fit the platform dimensions; it reduces external vibrations and stabilises weighing results. What are the exact dimensions and weight of the plate? The platform measures 565×450×60 mm and has a net weight of approximately 42 kg, giving sufficient mass for effective vibration isolation. Can the plate be used for microscopes and optical inspection? Yes, the antivibration plate is suitable for microscopes and other optical instruments, providing a vibration-reduced surface for clearer imaging and more consistent observations. How should the polished granite surface be cleaned and maintained? Polished granite on the antivibration plate is easy to maintain; clean with a mild detergent and soft cloth, avoid harsh abrasives, and check the rubber supports periodically for secure seating. Manufacturer: KERN; Dealer: Metav Werkzeuge, Emmerich am Rhein; Email: info@metav-werkzeuge.com; Phone: +49 2822 7131930; WhatsApp: +49 170 2837271

Take advantage of the precise OIML class E2 accuracy, polished stainless-steel finish and compact button form to ensure reproducible calibrations with minimal handling effort; order the weight directly via Metav Werkzeuge or consult our advisors for application-specific advice. KERN 317-08 — Calibration weight (200 g, OIML Class E2) The KERN 317-08 is a single OIML class E2 calibration weight in a button shape, designed for accurate mass checks in laboratories and workshop calibrations. OIML class E2 accuracy Nominal value 200 g Polished stainless steel finish Button shape for easy handling Guaranteed reproducibility for routine checks The calibrated mass delivers high-precision results thanks to its certified OIML class E2 specification and a rated tolerance of 0.3 mg, which supports repeatable measurements in quality control and calibration routines. This classification ensures the weight is suitable for fine laboratory balances and reference checks where small deviations matter. The compact dimensions and defined geometry reduce handling-related uncertainty, contributing to stable readings and fewer re-measurements. Robust finish and ergonomic handling Manufactured from polished stainless steel, the item resists corrosion and surface wear, maintaining its mass integrity over repeated use. The button shape simplifies placement on small pans and minimises tipping risk, which supports safe handling on sensitive balances. A protective case is recommended for storage to prevent surface contamination and preserve the mass value during transport; a selection of suitable cases is available in the accessories section for workshop and laboratory environments. Compliance advice and calibration pathway Note that EU type approval for weights ceased to be issued from 30.11.2025; for ongoing traceability and widespread application, a DAkkS calibration is recommended as an equivalent and recognised service for most requirements. Choosing DAkkS-calibrated weights maintains documented traceability and supports internal quality systems and audits. For users requiring documented conformity or routine recalibration intervals, integrating this weight into a documented calibration schedule will ensure compliance and measurement confidence. Contact Metav Werkzeuge in Emmerich for expert advice on DAkkS calibration, accessory options and to secure this high-precision KERN calibration weight for your workshop or laboratory Technical data Article number: 317 SKU: 317-08 GTIN: 4045761003668 Manufacturer: KERN Country of origin: DE Tariff number: 84239090 Facts Nominal value: 200 g Mass (kg): 0.2 Tolerance: 0.3 mg Cylinder dimensions: 28×47 mm Special features Polished stainless steel Button shape OIML class E2 Single weight configuration Protective case recommended DAkkS calibration recommended; EU type approval not available from 30.11.2025 FAQ What level of accuracy does this calibration weight provide? The KERN 317-08 calibration weight meets OIML class E2 and offers a tolerance of 0.3 mg, making it suitable for fine balances and reference checks that require high reproducibility. Can this weight be used for routine workshop calibrations? Yes; as a single 200 g polished stainless-steel weight, it is appropriate for routine calibration tasks in workshops and laboratories where class E2 accuracy is required. Is a protective case necessary for storage and transport? A protective case is recommended to prevent surface contamination and to maintain the mass value; Metav Werkzeuge offers suitable accessories in the product's accessories section. Is official type approval still available for this weight? EU type approval for calibration weights is no longer issued from 30.11.2025; for traceability and formal calibration needs, a DAkkS calibration is advised for the KERN 317-08. What calibration services are recommended for continued traceability? For documented traceability and audit readiness, DAkkS calibration is the recommended route; Metav Werkzeuge can advise on scheduling and service options for the KERN 317-08. Manufacturer: KERN; Address: Germany; Contact: not provided

Take advantage of a compact, standards-compliant accessory set that combines precise measurement support, easy handling and full compatibility with KERN analytical balances; order via Metav Werkzeuge or consult our specialists for tailored advice. Universal density set YDB-03 — density determination set for liquids and solids, DIN EN ISO 1183-1 compliant (KERN) The Universal density set YDB-03 is a complete accessory kit for precise density determination of liquids and solids on analytical balances, designed for laboratory and workshop quality control. Complete kit for liquid and solid density testing Compliant with DIN EN ISO 1183-1 testing wire Includes stainless steel 20 g sinker Suitable for all current KERN analytical balances Reliable results through standard‑compliant design The kit is built to deliver consistent, traceable density readings by meeting established testing practice. Compliance with DIN EN ISO 1183-1 and the specified 0.5 mm wire diameter for the immersion basket reduces measurement uncertainty when determining densities of non‑foamed plastics and similar materials. The standard conformity ensures that results are comparable across laboratories and that the procedure aligns with common quality assurance frameworks, making the set suitable for routine checks and documentation in production environments. Everything required for efficient and comfortable testing Designed as an all‑in‑one solution, the set contains a beaker (Ø×H 84×113 mm), thermometer, sample holder, adapter, counterweights, a stainless steel sinker (20 g) and a universal immersion basket for both floating and sinking specimens. These components reduce setup time and minimise handling errors, which in turn shortens the measurement cycle and improves throughput. The basket’s fine wire and the included sinker enable reliable immersion procedures for a wide range of materials, while the clear layout of accessories supports a reproducible workflow even for teams with varying experience. Seamless integration into analytical balance workflows Compatibility with KERN analytical balances ensures straightforward mounting and stable measurement conditions, preserving balance calibration and minimising re‑work. For applications requiring documented traceability, an optional DAkkS calibration certificate for the sinker is available, listing relevant density and volume data. The kit’s compact footprint and balanced weight distribution make it convenient for bench use and simple storage, supporting lean laboratory routines and steady sample throughput without compromising on measurement quality. Contact Metav Werkzeuge in Emmerich for expert advice and to secure the KERN accessory set for immediate integration into laboratory workflows Technical data Article number: YDB-03 Manufacturer: KERN GTIN: 4045761152908 Country of origin: Germany Facts Dimensions (beaker Ø×H): 84 × 113 mm Weight (set): 0.65 kg Sinker mass: 20 g Tension wire diameter: 0.5 mm Tariff number: 90160090 ECLASS: 32120490 Special features Includes: thermometer, sample holder, adapter, counterweights, stainless steel sinker (20 g) Universal immersion basket for floating and sinking solids Compliant with DIN EN ISO 1183-1 Suitable for all current KERN analytical balances Optional: sinker density determination, DAkkS calibration certificate (DKD) FAQ What is the set used for? The universal density set YDB-03 by KERN is intended for precise density determination of liquids and solids using analytical balances, suitable for laboratory and workshop quality checks. Is the immersion basket standard‑compliant? Yes. The immersion basket wire has a 0.5 mm diameter and complies with DIN EN ISO 1183-1, meeting the procedure requirements for density determination of non‑foamed plastics. What items are included in the delivery? Delivery comprises a beaker (Ø×H 84×113 mm), thermometer, sample holder, adapter, counterweights, a stainless steel 20 g sinker and a universal immersion basket for floating and sinking specimens. Can the set be used with existing KERN balances? The kit is designed to be compatible with all current KERN analytical balances and supports straightforward mounting and measurement routines. Is calibration available for traceability? An optional DAkkS calibration certificate is available for the sinker, providing documented values for density and volume where traceability is required. Manufacturer: KERN — Germany. Dealer contact: info@metav-werkzeuge.com | +49 2822 7131930