210 g Precision Analytical Balance 0.00001 g Readability, Graphic LCD, Internal Calibration, 160×170×225 mm Draft Shield - KERN

Take advantage of OIML E2 accuracy and the compact, polished stainless-steel design for reliable verification of precision balances; the 200 g nominal mass with 0.3 mg tolerance ensures consistent calibration results. Order this calibration weight via Metav Werkzeuge or contact our consultants for tailored advice on accessories and storage. KERN 316-08 Calibration weight (200 g, OIML E2) The KERN 316-08 is a compact calibration weight designed for precise verification of laboratory and industrial scales, featuring a polished stainless-steel finish and OIML E2 class accuracy OIML class E2 calibration grade Nominal value 200 g, compact form Polished stainless steel construction Tolerance 0.3 mg for high precision Accuracy that supports traceable results The core benefit of this calibration mass is its certified OIML E2 accuracy, which provides a tolerance of 0.3 mg for the nominal 200 g value. This level of precision makes the weight suitable for routine verification and adjustment of high-resolution balances where tight measurement uncertainty is required. The certification backing removes guesswork from conformity checks and supports documented measurement procedures in quality-controlled environments, offering a rational, efficiency-driven advantage for metrology workflows. Compact design for controlled handling and storage A compact profile and polished stainless steel surface reduce the influence of contaminants and ease cleaning, while the cylinder dimensions of 28×43 mm ensure stable placement on balance pans with limited space. The robust finish resists corrosion and minimises maintenance, translating into fewer interruptions in calibration routines. For long-term stability, storage in a protective case is recommended to prevent abrasion and contamination, preserving the mass’s reference value between verifications. Practical suitability across labs and workshops Manufactured to exacting standards in Germany, this single calibration weight supports accurate mass comparisons and routine traceability checks in laboratories, production control and service environments. The compact form factor simplifies transport within a calibration set and the stable geometry reduces sensitivity to handling errors. By integrating such a reference mass into regular procedures, measurement reliability improves and audit readiness is strengthened, delivering both operational and compliance benefits. Contact Metav Werkzeuge in Emmerich for expert advice on the KERN 316-08 calibration weight, accessory recommendations such as protective cases, and reliable supply for workshop or laboratory needs Technical data Article number: 316 SKU: 316-08 GTIN: 4045761094901 Manufacturer: KERN Key measurements Nominal value: 200 g Mass (kg): 0.2 kg Cylinder dimensions: 28×43 mm OIML tolerance: 0.3 mg Tariff code: 84239090 Materials and features Material: polished stainless steel Form: compact form OIML class: E2 Origin: Germany Recommended accessory: protective case (etui) FAQ What is the intended use of this calibration weight? The KERN 316-08 calibration weight is intended for verification and adjustment of precision balances and scales where OIML E2 class accuracy is required. How precise is the 200 g weight? The nominal 200 g mass has an OIML E2 tolerance of 0.3 mg, ensuring high repeatability for laboratory and industrial verification tasks. Is the weight suitable for regular transport between sites? The compact form and polished stainless-steel construction make the weight suitable for transport, provided it is carried in a protective case to avoid contamination or mechanical damage. How should the weight be stored to preserve accuracy? Storage in a dedicated protective case (etui) is recommended to prevent abrasion and contamination and to maintain long-term stability of the calibration mass. Does this weight come with certification or traceability information? The OIML E2 classification indicates the weight meets internationally recognised calibration standards; specific certificates or documentation can be requested when purchasing the KERN 316-08. Metav Werkzeuge, Emmerich am Rhein, Germany — eMail: info@metav-werkzeuge.com — Phone: +49 2822 7131930 — WhatsApp: +49 170 2837271

Take advantage of reliable dust protection and light shielding to preserve measurement accuracy, with broad compatibility for KERN analytical and precision balances featuring a glass wind shield. Supplied as a practical pack of five, this cover supports smooth workflow and low-maintenance operation. Order directly via Metav Werkzeuge or consult our technical advisors for application guidance. Dust cover ABS-A08 – protective cover for analytical and precision balances by KERN The dust cover ABS-A08 is a protective cover designed for KERN analytical and precision balances with a glass wind shield, preventing contamination and ambient light interference during sensitive weighing tasks. Protects against dust and light Compatible with KERN analytical balances Designed for balances with glass wind shield Supplied as pack of 5 Preserve measurement integrity with simple protection A lightweight protective cover reduces the risk of sample contamination and measurement drift, supporting consistent measurement integrity in laboratories and production areas. Dust particles and stray light can alter readings on highly sensitive instruments; by placing a cover over the balance’s glass draft shield, settling particles are kept away from the weighing pan and reflective light is minimised. This results in fewer repeat measurements and less time spent on corrective cleaning, which translates into improved process efficiency and more reliable data for quality control. Fast fit for analytical and precision balances The cover is engineered to fit balances that incorporate a glass wind shield, enabling quick placement and removal during routine operations. Compatibility with a wide range of KERN models simplifies stocking decisions for procurement teams: one standard accessory supports multiple instruments. The supply in a pack of five is practical for facilities running several weighing stations or for replacing worn covers without delay. The design prioritises unobtrusive protection so that normal workflow—placing samples, adjusting weights and reading results—remains straightforward. Practical benefits for workshop and lab routines Using a protective cover supports the longevity of sensitive weighing equipment by reducing particulate ingress and light-induced reading anomalies. For teams focused on throughput and traceable results, the cover contributes to operational stability and reduces the frequency of maintenance interventions. The accessory is a cost-effective way to protect investment in precision equipment while helping to maintain the reproducibility required in analytical work and small-batch production. For tailored advice or to order the KERN dust cover ABS-A08 in practical multi-packs, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for precise guidance and reliable supply. Technical Data Article number: ABS SKU: ABS-A08 Manufacturer: KERN GTIN: 4045761163348 Country of origin: China Tariff number: 39269097 ECLASS: 24322502 Numbers Weight: 0.01 kg Pack quantity: 5 Special features Protects against dust and light Fits KERN analytical and precision balances with glass wind shield Supplied as pack of 5 FAQ Is this cover suitable for all KERN analytical balances? The dust cover ABS-A08 is compatible with KERN analytical and precision balances that feature a glass wind shield. How often should the cover be replaced? Replacement frequency depends on usage and contamination levels; the ABS-A08 is supplied as a pack of five to allow regular replacement when required. Can the cover be used with non-KERN balances? The design targets balances with a glass draft shield; fit with other brands depends on the specific dimensions and draft-shield configuration, so compatibility should be checked against the balance’s glass wind shield. Does the cover protect against light as well as dust? Yes, the cover shields samples from ambient light while also preventing dust settlement, both of which help to maintain stable readings. Is material information available for the cover? Material details are not specified in the provided product data Manufacturer: KERN — Address and contact details not provided in the product data

Protect valuable weighing electronics by combining a simple keyboard and housing protective cover with the convenience of a pack format and lightweight handling; order directly via Metav Werkzeuge or consult the specialists for fit and availability. KERN ALJ-A01S05 Protective Cover — durable keyboard and housing protection, pack format The ALJ-A01S05 protective cover is designed to shield scale keyboards and housings in industrial and workshop settings, offering a practical barrier against contamination while preserving device functionality. Protective cover for keyboard and housing Supplied as a pack of 5 pieces Lightweight design at 0.02 kg Suitable for scales and measurement units Reduce maintenance and downtime with straightforward protection The protective cover provides a cost-effective barrier that helps keep keyboards and housings free from dust and light contamination, reducing the need for frequent cleaning and maintenance. By preventing ingress of particles and debris, sensitive components are less likely to require service interruptions, which supports a more efficient production flow. The slim design ensures that the control surfaces remain accessible while receiving reliable coverage, supporting continued measurement accuracy in everyday use. Practical pack format for workshops and multi-unit environments Delivered as a pack of 5, this solution simplifies inventory management for workshops and inspection stations, enabling rapid replacement and consistent protection across several workstations. The compact weight of 0.02 kg per item keeps storage and handling straightforward, while the standard dimensions are suitable for common scale housings. Clear labelling and bulk supply reduce procurement cycles and help maintain uninterrupted operation of weighing equipment. Built for compatibility and simple deployment Manufactured by KERN, the cover is tailored for use over keyboards and housings associated with scales and related measuring devices. The accessory is particularly useful for environments where particulate contamination or incidental spillovers are a concern and where easy-to-change protective elements are preferred. Its design supports quick fitting and disposal or replacement, aligning with routine maintenance practices and operational hygiene requirements. Contact Metav Werkzeuge to secure KERN protective covers (ALJ-A01S05) — our consultants will advise on suitability and ensure prompt dispatch from Emmerich. Technical data Article number: ALJ-A01S05 Manufacturer: KERN SKU: ALJ-A01S05 GTIN: 4045761184589 Origin: China Facts Weight: 0.02 kg Tariff code: 39269097 Special features Pack contents: 5 protective covers Application: protection for keyboards and housings of scales Category: scale accessories FAQ Is the ALJ-A01S05 cover compatible with common scale keyboards? The ALJ-A01S05 protective cover by KERN is designed for use over keyboards and housings typical of scale equipment and offers broad compatibility with standard control surfaces. How is the product supplied and what is included? The product is supplied as a pack of 5 protective covers (ALJ-A01S05), allowing for multiple replacements or coverage across several devices. Can the cover be used in production and laboratory environments? Yes, the KERN protective cover is suitable for industrial and workshop settings where protection of measuring electronics and hygiene are priorities. Does the cover add significant weight or bulk to the device? The cover has a lightweight design at approximately 0.02 kg and is intended to provide protection without impairing access to controls or significantly altering the device profile. Where can information about ordering and availability be obtained? For ordering details and availability of the KERN ALJ-A01S05 protective cover, contact Metav Werkzeuge; consult the product listing or reach out for advice on stock and dispatch. Manufacturer: KERN; Origin: China; Contact: info@metav-werkzeuge.com | +49 2822 7131930

Take advantage of fast, reliable printing together with plain‑paper archiving and an automatic cutter for streamlined weighing documentation; order the unit directly via Metav Werkzeuge or consult our specialists for integration advice. YKG-01 dot‑matrix printer by KERN — 4.7 lines/s, automatic cutter The YKG-01 is a compact dot‑matrix printer for retail, hospitality and kitchen environments, designed to print weighing results on plain paper for reliable, long‑term archiving. Fast dot‑matrix print at 4.7 lines/s Prints weighing values on plain paper Built‑in automatic paper cutter Interchangeable interface, cable not included Dependable output for retail and catering operations The unit delivers consistent impact printing that is optimised for the frequent, short receipts typical in shops and kitchens. With a rated speed of 4.7 lines/s and a maximum of 42 characters per line, the mechanism ensures legible, evenly spaced output that suits both immediate transaction needs and longer‑term record keeping. Using plain paper instead of thermal rolls reduces running costs and enables simple archival procedures, while the printer’s robust construction resists the knocks and humidity common in catering environments. Simple integration and low‑effort maintenance Engineered for straightforward connection in point‑of‑sale setups, the model provides an interchangeable interface to match existing systems; note that the interface cable is not included. The supplied EU power adapter supports 230 V AC, 50 Hz supplies, and the plug‑in power design keeps replacement simple. Routine consumable changes are fast: the design allows easy paper and ribbon replacement without specialised tools, reducing downtime and keeping staff focused on service rather than maintenance. Archive‑ready receipts and controlled operating range Because the printer produces records on plain paper, documents withstand longer storage and are compatible with conventional filing systems. The integrated automatic paper cutter gives a clean finish to each slip, improving handling and reducing errors when collecting multiple receipts. For reliable use, the device is specified for operation between 5 °C and 35 °C, and its compact footprint suits busy counters and compact kitchen stations, contributing to an orderly, compliant documentation workflow. Contact Metav Werkzeuge for an expert recommendation on integrating the KERN YKG‑01 into the workflow and to arrange supply directly from our Emmerich warehouse – eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: YKG SKU: YKG-01 Manufacturer: KERN Origin: JP GTIN: 4045761253056 Facts Dimensions: 160 x 248 x 139 mm Weight: 2.71 kg Print speed: 4.7 lines/s Max characters per line: 42 Power input: 230 V AC, 50 Hz Paper widths: 58, 70, 76 mm Operating temperature: 5 °C–35 °C Special features Printing method: impact (dot‑matrix) Power supply: EURO plug‑in adapter Built‑in automatic paper cutter Interchangeable interface (cable not included) Designed for plain‑paper receipt archiving FAQ How does the YKG‑01 handle receipt archiving? The KERN YKG‑01 prints on plain paper, producing durable receipts suitable for standard filing and longer retention periods. Is an interface cable included with the printer? No, the printer is supplied with an interchangeable interface but the interface cable is not included and must be provided separately. What power supply is required for the unit? The unit uses a 230 V AC, 50 Hz supply and is shipped with a EURO plug‑in adapter. Can the printer be used in a kitchen environment? Yes, the design and impact printing method make it suitable for retail and catering settings; operating conditions should remain within 5 °C–35 °C. What makes this model suitable for point‑of‑sale systems? Its compact size, fast 4.7 lines/s output, automatic paper cutter and interchangeable interface facilitate simple integration into POS workflows. Metav Werkzeuge — Emmerich (warehouse and quality hub); Contact: info@metav-werkzeuge.com; Tel: +49 2822 7131930; WhatsApp: +49 170 2837271

Take advantage of a dependable RS-232 connection and a practical 1.5 m cable length to integrate weighing equipment into existing data workflows with minimal effort; combine reliability and straightforward installation for uninterrupted measurement logging. Order the interface cable directly via Metav Werkzeuge or consult our advisors for application guidance. KERN RS-232 interface cable 572-926 — RS-232 connection, 1.5 m cable The KERN RS-232 interface cable 572-926 is a dedicated accessory for scales and weighing systems that enables stable serial data transfer between instruments and computers. RS-232 interface for reliable data transfer Cable length 1.5 m for flexible placement Accessory for scales and weighing systems Seamless data transfer for weighing workflows The RS-232 connection provides a proven, low-latency way to export measurement values from a scale to a PC, printer or data logger. With a 1.5 m cable length the lead offers practical reach across a bench or workstation without excess slack, simplifying cable routing. As an accessory designed for weighing equipment, the cable reduces interruptions in data acquisition and supports continuous logging processes, which is particularly useful where serial output remains the standard for industrial metrology. The compact design and light weight contribute to simple handling and less strain on instrument ports. Robust serial interface explained for practical use The serial standard implemented by this cable is valued for its stability in industrial and workshop environments. Unlike many casual consumer connections, RS-232 maintains clear signal levels over short runs and is tolerant of typical workshop interference when properly installed. The cable serves as a direct link for numeric transfer and simple control messages, enabling automated data capture or label printing without complex network configuration. Where reliable point-to-point communication is required, this interface cable provides a technically straightforward solution that integrates with legacy and contemporary weighing equipment alike. Practical benefits that support uptime and workflow Lightweight construction and a focused specification minimise installation time and downtime during equipment setup or replacement. The cable’s specification suits regular workshop use and makes it easier to standardise interfaces across a fleet of scales. Purchasing via Metav Werkzeuge brings the additional assurance of curated product selection and centralised supply: Metav combines decades of precision expertise with extensive stockholding to support reliable deliveries to the shop floor. For procurement, the compact packing and predictable compatibility help keep logistics simple and maintenance predictable. Contact Metav Werkzeuge to arrange supply of the KERN RS-232 interface cable 572-926 and to discuss integration options for existing weighing systems Technical data Article number: 572-926 Manufacturer: KERN GTIN: 4045761245211 Country of origin: CN Tariff code: 84239010 Numbers / Core technical data Weight: 0.08 kg Cable length: 1.5 m SKU: 572-926 Special features RS-232 serial interface Accessory for scales (weighing systems) Category: Scales, accessories FAQ What type of interface does this cable provide? The cable provides an RS-232 serial interface suitable for point-to-point data transfer from scales to computers or printers. What is the cable length and how flexible is it for workshop use? The cable length is 1.5 m, offering practical reach for bench-top installations and tidy routing in workstations. Is this cable suitable for KERN weighing instruments? Yes, the cable is a KERN accessory (SKU 572-926) designed to connect with weighing equipment that features an RS-232 output. Can the cable be used for continuous data logging? The RS-232 connection supplied by this cable supports reliable numeric data transfer and is suitable for straightforward continuous logging setups. Manufacturer: KERN — Origin: China. Dealer and contact: Metav Werkzeuge, Emmerich am Rhein. Email: info@metav-werkzeuge.com, Phone: +49 2822 7131930

Take advantage of precise measurement results through robust vibration damping and a heavy, polished granite surface that stabilises sensitive instruments; compact dimensions and hygienic surfaces support ergonomic use in space-constrained labs. Order the antivibration plate directly via Metav Werkzeuge or contact our consultants for tailored advice and fast dispatch. KERN YPS-05 Antivibration Plate — Polished granite, 565×450×60 mm The KERN YPS-05 is an antivibration plate designed to isolate analytical balances and microscopes from vibrations, providing a stable working surface for high-precision measurements Polished granite on resilient rubber supports Suitable for analytical balances and microscopes Compact footprint 565×450×60 mm Hygiene-friendly, easy-to-clean surfaces Reduce measurement errors with a stable work surface High-precision weighing and optical inspection require a stable base to prevent fluctuating results. The KERN YPS-05 combines mass and material to provide effective vibration damping: the dense polished granite top increases inertia, while the support system attenuates external shocks. This construction reduces measurement scatter and the need for repeat tests, which improves throughput and ensures repeatable results for both routine and traceable analytical tasks. The described behaviour of the platform is particularly relevant when using analytical balances, where even small vibrations can affect the displayed value. Compact footprint that supports ergonomic workflows A small laboratory bench or a crowded workshop does not need to compromise on measurement quality. With overall dimensions of 565×450×60 mm, the plate fits tight workspaces while allowing ergonomic operation either standing or seated. The top surface is finished for cleanliness: hygienic surfaces are easy to wipe down and maintain, supporting contamination control in sensitive environments. The low-profile design enables comfortable access to instruments and ancillary equipment and is tailored to accommodate KERN precision instruments and microscopes with corresponding base sizes. Robust build and ready logistics for uninterrupted operation Durability is central to a long service life and consistent performance. The YPS-05 rests on absorbing rubber elements that decouple the granite slab from bench vibrations and protect the platform from transmitted shocks. This arrangement creates a dependable working surface that preserves instrument calibration and extends operational uptime. For operational planning, the unit is shipping ready in 2 days and delivered palletised, reducing lead times and simplifying installation. The combination of a heavy top and resilient supports yields a stable base that lowers the frequency of adjustments and supports efficient lab routines. For reliable vibration control choose the KERN YPS-05 and contact Metav Werkzeuge in Emmerich for expert advice and prompt palletised dispatch Technical Data Article number: YPS-05 SKU: YPS-05 Manufacturer: KERN GTIN: 4045761253568 Dimensions: 565×450×60 mm Material: Polished granite Origin: DE Commodity code: 84239010 ECLASS: 21170605 Facts Dimensions: 565×450×60 mm Net weight: approx. 42 kg Shipping: ready in 2 days Commodity code: 84239010 ECLASS: 21170605 Special features Material: polished granite Mounted on absorbing rubber elements Hygienic, easy-to-clean surfaces Ergonomic use standing or sitting Suitable for KERN analytical and precision balances and microscopes with corresponding dimensions Shipping: palletised FAQ Is the antivibration plate compatible with analytical balances? The KERN YPS-05 antivibration plate is designed for use with KERN analytical balances and precision scales that fit the platform dimensions; it reduces external vibrations and stabilises weighing results. What are the exact dimensions and weight of the plate? The platform measures 565×450×60 mm and has a net weight of approximately 42 kg, giving sufficient mass for effective vibration isolation. Can the plate be used for microscopes and optical inspection? Yes, the antivibration plate is suitable for microscopes and other optical instruments, providing a vibration-reduced surface for clearer imaging and more consistent observations. How should the polished granite surface be cleaned and maintained? Polished granite on the antivibration plate is easy to maintain; clean with a mild detergent and soft cloth, avoid harsh abrasives, and check the rubber supports periodically for secure seating. Manufacturer: KERN; Dealer: Metav Werkzeuge, Emmerich am Rhein; Email: info@metav-werkzeuge.com; Phone: +49 2822 7131930; WhatsApp: +49 170 2837271

Take advantage of a compact, standards-compliant accessory set that combines precise measurement support, easy handling and full compatibility with KERN analytical balances; order via Metav Werkzeuge or consult our specialists for tailored advice. Universal density set YDB-03 — density determination set for liquids and solids, DIN EN ISO 1183-1 compliant (KERN) The Universal density set YDB-03 is a complete accessory kit for precise density determination of liquids and solids on analytical balances, designed for laboratory and workshop quality control. Complete kit for liquid and solid density testing Compliant with DIN EN ISO 1183-1 testing wire Includes stainless steel 20 g sinker Suitable for all current KERN analytical balances Reliable results through standard‑compliant design The kit is built to deliver consistent, traceable density readings by meeting established testing practice. Compliance with DIN EN ISO 1183-1 and the specified 0.5 mm wire diameter for the immersion basket reduces measurement uncertainty when determining densities of non‑foamed plastics and similar materials. The standard conformity ensures that results are comparable across laboratories and that the procedure aligns with common quality assurance frameworks, making the set suitable for routine checks and documentation in production environments. Everything required for efficient and comfortable testing Designed as an all‑in‑one solution, the set contains a beaker (Ø×H 84×113 mm), thermometer, sample holder, adapter, counterweights, a stainless steel sinker (20 g) and a universal immersion basket for both floating and sinking specimens. These components reduce setup time and minimise handling errors, which in turn shortens the measurement cycle and improves throughput. The basket’s fine wire and the included sinker enable reliable immersion procedures for a wide range of materials, while the clear layout of accessories supports a reproducible workflow even for teams with varying experience. Seamless integration into analytical balance workflows Compatibility with KERN analytical balances ensures straightforward mounting and stable measurement conditions, preserving balance calibration and minimising re‑work. For applications requiring documented traceability, an optional DAkkS calibration certificate for the sinker is available, listing relevant density and volume data. The kit’s compact footprint and balanced weight distribution make it convenient for bench use and simple storage, supporting lean laboratory routines and steady sample throughput without compromising on measurement quality. Contact Metav Werkzeuge in Emmerich for expert advice and to secure the KERN accessory set for immediate integration into laboratory workflows Technical data Article number: YDB-03 Manufacturer: KERN GTIN: 4045761152908 Country of origin: Germany Facts Dimensions (beaker Ø×H): 84 × 113 mm Weight (set): 0.65 kg Sinker mass: 20 g Tension wire diameter: 0.5 mm Tariff number: 90160090 ECLASS: 32120490 Special features Includes: thermometer, sample holder, adapter, counterweights, stainless steel sinker (20 g) Universal immersion basket for floating and sinking solids Compliant with DIN EN ISO 1183-1 Suitable for all current KERN analytical balances Optional: sinker density determination, DAkkS calibration certificate (DKD) FAQ What is the set used for? The universal density set YDB-03 by KERN is intended for precise density determination of liquids and solids using analytical balances, suitable for laboratory and workshop quality checks. Is the immersion basket standard‑compliant? Yes. The immersion basket wire has a 0.5 mm diameter and complies with DIN EN ISO 1183-1, meeting the procedure requirements for density determination of non‑foamed plastics. What items are included in the delivery? Delivery comprises a beaker (Ø×H 84×113 mm), thermometer, sample holder, adapter, counterweights, a stainless steel 20 g sinker and a universal immersion basket for floating and sinking specimens. Can the set be used with existing KERN balances? The kit is designed to be compatible with all current KERN analytical balances and supports straightforward mounting and measurement routines. Is calibration available for traceability? An optional DAkkS calibration certificate is available for the sinker, providing documented values for density and volume where traceability is required. Manufacturer: KERN — Germany. Dealer contact: info@metav-werkzeuge.com | +49 2822 7131930

Take advantage of precise static control and quick retrofit installation to reduce weighing errors and downtime; the integrated ioniser neutralises electrostatic charge while the panel replaces the existing glass rear panel, maintaining enclosure integrity. Order the KERN ALJ-A03 via Metav Werkzeuge or consult our advisors for application guidance. Draft-shield rear panel (KERN ALJ-A03) with integrated ioniser for scales A Draft-shield rear panel fitted with an integrated ioniser, designed to replace the glass rear panel of a weighing draft shield and to neutralise electrostatic charges that can skew sensitive measurements. *Integrated ioniser neutralises electrostatic charge *Replaces existing glass rear panel of the draft shield *Compact, lightweight design (0.53 kg) Ensure measurement reliability by removing electrostatic interference The addition of an integrated ioniser directly addresses the common source of weighing variation caused by electrostatic charge on samples, packaging or containers. In laboratory and industrial weighing, even minute static fields can attract or repel the pan load and distort results; the retrofittable rear panel provides targeted neutralisation inside the draft shield, improving repeatability and reducing the need for repeated tare cycles. This technical improvement translates into measurable time savings and fewer rejected readings. Fast retrofit that preserves enclosure performance and workflow Designed to be mounted in place of the existing glass rear panel, the replacement panel offers a straightforward upgrade path for balances and enclosed weighing stations without altering the front enclosure or balance mounting. The lightweight 0.53 kg construction keeps handling safe while minimising the risk of imbalance or stress on the draft shield assembly. As a factory-option accessory from KERN, the component integrates with standard enclosures and helps reduce downtime compared with complete enclosure replacement. Practical applications and reduced process variability The panel is particularly effective when weighing powders, films or charged plastics where static can produce inconsistent readings. By neutralising charge inside the weighing enclosure, the solution supports tighter process control in QC checks, formulation tasks and laboratory dosing operations. Specifying this accessory helps standardise measurement conditions across multiple workstations, supporting traceable procedures and better overall quality assurance. Request the KERN ALJ-A03 through Metav Werkzeuge for improved static control in weighing enclosures — contact our consultants at info@metav-werkzeuge.com or call +49 2822 7131930 for detailed compatibility advice. Technical Data Article number: ALJ-A03 Manufacturer: KERN SKU: ALJ-A03 GTIN: 4045761206809 Country of origin: CN Facts Net weight: 0.53 kg Commodity code: 90160090 Special features Integrated ioniser for neutralising electrostatic charge Mounts instead of existing glass rear panel Factory option Product category: Scales accessories FAQ How does the integrated ioniser improve weighing results? The integrated ioniser in the KERN rear panel neutralises electrostatic charge within the draft shield, reducing attraction or repulsion effects that cause unstable or drifting readings. Is the panel compatible with existing draft shields? Compatibility depends on the draft shield geometry; the KERN ALJ-A03 is designed to replace the glass rear panel of standard weighing enclosures, and further compatibility details can be provided by Metav Werkzeuge. Will installation require modification of the balance? The panel is intended as a retrofit replacement for the rear glass panel and normally requires no modification to the balance itself; exact fitment should be checked against the enclosure model. Can the accessory be used in environments with sensitive samples such as powders or films? Yes, the neutralising function of the KERN rear panel helps stabilise measurements for charged powders, films and plastic components, lowering variability in such applications. KERN — Origin: CN, SKU ALJ-A03