ANHX 100405 Indexable Insert for Aluminium - MetavCUT

Product Information: Order Number: T659TM Item: Face Mill usable with ANHX 1004 Indexable Inserts of Palbit Brand: Teknik Makina Numbers and Data: Diameter: 80mm Cutting Edges: 8 Weight: 1.132kg Total length: 50mm Diameter Connection: 27mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Take advantage of the combination of 90° cutting geometry, a 63 mm body diameter and a 22 mm shank to secure stable, repeatable corner turning. Benefit from compatibility with ANHX 1004 indexable inserts and reliable mounting using the M3x7 Torx fastening. Order the tool directly via Metav Werkzeuge or consult the advisors for application-specific guidance. Eckmesserkopf — Corner cutting head with 90° geometry for ANHX 1004 indexable inserts (Teknik Makina) The Eckmesserkopf is a compact corner cutting head engineered for precise 90° turning operations using ANHX 1004 indexable inserts; ideal where rigidity and repeatability matter in production and jobbing shops. 90° cutting angle for precise corner turning Compatible with ANHX 1004 indexable inserts 63 mm body diameter for rigid stability 22 mm shank diameter for secure mounting Consistent geometry for predictable machining results The corner cutting head delivers a 90° cutting angle combined with a Ø63 mm body to reduce vibration and deflection during side and face turning. The hardened connection to the machine spindle and the 22 mm shank ensure a secure fit, translating spindle power into cutting performance with minimal loss. This design yields repeatability across batches and reduces scrap rates by stabilising chip formation and tool engagement. Fast insert changes and secure clamping cut downtime Compatibility with ANHX 1004 indexable inserts and the Palbit insert form means insert swaps are straightforward and standards-based. The head uses an M3x7 Torx fastening and a T8 Torx key for positive clamp torque, which keeps the insert seated reliably. Reduced tool-change time and dependable clamping improve uptime and support consistent cycle times on turning centres. Built for everyday workshop use with dependable handling With a modest mass of 0.638 kg and a compact overall length of 40 mm, the head is easy to manoeuvre during tool set-up yet robust enough for repeated operation. The configuration features seven cutting edges, promoting efficient indexing strategies where multi-edge inserts are used. The combination of compact dimensions and a rigid interface supports both short overhangs and close-tolerance face turning. Practical benefits for purchasing and inventory decisions Choosing this corner cutting head simplifies tooling logistics: it fits a common insert format and fastener type, helping standardise the tooling pool. The technical profile — Ø63 mm, 22 mm shank, 90° geometry — supports wide applicability across medium-duty turning tasks, allowing procurement teams to reduce the number of specialised holders required on the shop floor. Select Teknik Makina’s corner cutting head for its proven geometry and compatibility, and contact Metav Werkzeuge to arrange supply or technical consultation directly from Emmerich. Technical data Article number: T658TM Manufacturer: Teknik Makina Facts Diameter: 63 mm Overall length: 40 mm Shank diameter: 22 mm Weight: 0.638 kg Cutting angle: 90° Cutting edges: 7 ECLASS: 21181015 Features Compatible inserts: ANHX 1004 Compatible insert manufacturer: Palbit Torx key size: T8 Torx screw: M3x7 Brand: Teknik Makina FAQ Which indexable inserts fit this cutting head? The Eckmesserkopf is designed for ANHX 1004 indexable inserts; Palbit-format inserts are compatible and recommended for correct seating and performance. What is the required shank or toolholder interface? This corner cutting head features a 22 mm shank diameter for secure mounting in compatible tool turrets or holders. Which fastening hardware is supplied or required? Clamping is achieved using an M3x7 Torx screw tightened with a T8 Torx key; the specification is included in the product details for workshop preparation. Is the head suitable for tight, repeatable corner turning? Yes — the 90° geometry, Ø63 mm body and compact 40 mm length provide rigidity and repeatability for precise corner and face turning operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-rigidity turning solution with a 50 mm head diameter and a 22 mm shank for stable set-ups; the 90° cutting angle ensures precise square-shoulder cuts while compatibility with ANHX 1004 indexable inserts keeps tooling costs predictable. Order directly via Metav Werkzeuge or ask our consultants for application advice. Eckmesserkopf T657TM – corner turning head, 50 mm diameter, 90° cutting angle (Teknik Makina) The Eckmesserkopf is a corner turning head for ANHX 1004 indexable inserts, engineered for precision shoulder and facing operations in turning applications 50 mm head diameter for rigid set-up 90° cutting angle for square shoulder cuts Compatible with ANHX 1004 Palbit inserts Fast clamping with M3x7 Torx screw Accurate shoulder cuts and reliable rigidity The turning head delivers a compact solution for repeatable square-shoulder machining thanks to its 50 mm head diameter and 90° cutting angle, which combine to reduce deflection during interrupted cuts. The unit’s 22 mm shank contributes to a stable clamping interface in standard toolholders, improving surface finish and dimensional consistency. Designed for indexable insert technology, the head accepts ANHX 1004 inserts, translating indexable insert benefits—fast edge changes and consistent cutting geometry—into lower process downtime and predictable tool costs. Secure clamping and straightforward insert changes A robust clamping design with the supplied M3x7 Torx screw and matching T8 key enables quick insert replacement while maintaining repeatable seat location and torque. The tool’s modest overall length of 40 mm and mass (approx. 0.347 kg) help balance the assembly, decreasing vibration at higher spindle speeds and extending insert life. Practical maintenance is supported by a simple fastener system; correct use of the Torx key ensures consistent clamping force and reduces the risk of misalignment during production. Practical benefits in production workflows Suitable for general turning and finishing tasks where square shoulders and precise depths are required, this corner turning head provides a reliable mechanical interface for Palbit-compatible indexable inserts. The presence of five cutting edges on compatible inserts (per insert specification) provides multiple resharpen-equivalent edges before replacement, delivering cost efficiency. Specified dimensions and repeatable clamping aid programming accuracy and shorten set-up times, making the head a pragmatic choice for batch production and mixed-job workshops seeking consistent results. For expert advice on integrating this Teknik Makina corner turning head into an existing toolchain or to place an order, contact Metav Werkzeuge for tailored recommendations and reliable supply from Emmerich; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: T657TM Manufacturer: Teknik Makina Facts Head diameter: 50 mm Overall length: 40 mm Shank diameter: 22 mm Weight: 0.347 kg Cutting angle: 90° Torx key: T8 Torx screw: M3x7 Number of cutting edges: 5 Special features For ANHX 1004 indexable inserts Compatible with Palbit inserts Corner turning / square-shoulder application Compact, rigid design FAQ What insert type does this turning head accept? The turning head accepts ANHX 1004 indexable inserts; compatibility with Palbit variants is indicated for flexible tooling choices when using the T657TM corner head from Teknik Makina. What are the critical dimensions for setting up the tool? Relevant dimensions include a 50 mm head diameter, 22 mm shank diameter and 40 mm overall length for correct insertion and clamping in compatible toolholders. Which fastener and key are required for insert clamping? Clamping is achieved with an M3x7 Torx screw, tightened with a T8 Torx key to ensure secure, repeatable seat location on the T657TM head. Is the head suitable for heavy roughing or finishing? The compact, rigid design and 90° cutting angle are optimised for precise shoulder and finishing operations; suitability for heavy roughing depends on machine power, insert grade and cutting parameters. How does the head contribute to shorter set-up times? Standardised dimensions and a simple Torx clamping system allow fast insert changes and consistent positioning, reducing downtime during tool changes and enabling quicker return to production. Manufacturer: Teknik Cutting Tools; Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust 90° corner solution that accepts Palbit ANHX 1004 indexable inserts and mounts on a 16 mm interface for secure, repeatable results; order or request advice via Metav Werkzeuge for straightforward integration into the production line. Corner tool head — 90° for ANHX 1004 indexable inserts (Teknik Makina T656TM) The corner tool head is a compact 90° turning head designed for external machining and precise corner cuts using ANHX 1004 indexable inserts. Precision 90° cutting angle for corner work Compatible with Palbit ANHX 1004 inserts 16 mm shank for secure toolholder mounting Compact 40 mm head with four cutting edges Maximise turning accuracy with a 90° cutting angle The compact holder provides a 90° cutting angle that keeps cutting forces predictable and concentrates the geometry where corner accuracy matters most. Fitted for ANHX 1004 indexable inserts, this head converts each insert index into renewed cutting life, reducing tool-change frequency and improving uptime. The presence of four cutting edges extends service intervals, while the use of indexable technology keeps machining consistent across batches. The design supports repeatable results in serial turning and intermittent finishing tasks. Secure mounting and quick, reliable clamping A 16 mm shank ensures firm seating in standard toolholders and minimises runout when compared with smaller interfaces; the nominal shank diameter contributes to consistent tool alignment. Clamping is achieved with an M3x7 torx screw and the matching T8 key, providing secure locking without the need for special fixtures. The straightforward fastening arrangement allows fast setup changes and predictable torque behaviour, which helps keep cycle times stable in mixed-production environments. Compact form for confined workspaces and steady performance With a 40 mm head diameter and an overall length of 40 mm, the holder keeps the cutting point close to the spindle centre, improving rigidity and reducing overhang-induced vibration. At approximately 0.25 kg, the assembly is light enough for agile tool changes yet robust enough for everyday workshop use. The compact package is ideal where access is restricted or where multiple tool stations operate in close proximity, enabling efficient nesting of tools without compromise to cutting reliability. Low-maintenance operation and predictable throughput The indexable concept reduces complex maintenance to a few quick actions: index, tighten and resume production. Replaceable inserts mean that wear does not require discarding the entire holder, so shop-floor maintenance is simplified and spare-part inventories remain compact. The holder’s geometry and straightforward fixing method support predictable performance and easier process documentation, helping to plan tool life and control cost-per-part across series production. For fast technical advice and availability of the Teknik Makina T656TM corner tool head, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss integration and delivery from Emmerich Technical data Article number: T656TM Manufacturer: Teknik Makina Suitable for inserts: ANHX 1004 (Palbit) SKU: T656TM Core data Diameter: 40 mm Overall length: 40 mm Shank diameter: 16 mm Cutting angle: 90° Cutting edges: 4 Weight: 0.25 kg Torx screw: M3x7 Torx key: T8 Features For ANHX 1004 indexable inserts Compatible with Palbit inserts 90° corner head geometry Compact design for confined spaces Secure clamp with M3x7 torx screw FAQ Which indexable inserts fit this holder? The T656TM corner tool head accepts Palbit ANHX 1004 indexable inserts and is specified for that insert form. What shank diameter is required for mounting? The holder uses a 16 mm shank interface and is designed for compatible toolholders with that diameter. How many cutting edges are available per insert position? The assembly is built around a head with four cutting edges, enabling multiple indexings before insert replacement. Which screw and key are required for clamping the insert? Clamping is performed with an M3x7 torx screw tightened using a T8 torx key. Is the head suitable for tight access or compact workpieces? Yes — the 40 mm head diameter and 40 mm overall length make the holder suitable for confined machining areas and closely packed tooling setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a stable tool geometry and wide compatibility: the combination of a 32 mm shaft and compatibility with ANHX 1004–1206 indexable inserts ensures repeatable milling performance and straightforward maintenance. Order the S785TM directly via Metav Werkzeuge or contact the consultants for precise technical guidance. S785TM Milling Cutter (indexable) – 32 mm diameter, 4-flute by Teknik Makina The S785TM is a robust indexable milling cutter designed for ANHX 1004–1206 indexable inserts, intended for general milling tasks in workshop and light production environments. 32 mm shaft diameter for stable clamping Compatible with ANHX 1004–1206 inserts 40 mm cutting length for deeper cuts Torx T8 screw M3x7 for secure insert fixation Stable geometry for consistent, accurate milling The cutter's 32 mm shaft diameter and 4 flutes deliver a rigid connection between spindle and cutting head, which reduces vibration and improves dimensional repeatability. A 90° cutting angle provides predictable engagement with the workpiece and is well suited to face and shoulder milling operations. For users who require reproducible tolerances, the rigid shaft and balanced flute count help maintain tool life and part quality, while the modest overall mass (approx. 0.136 kg) keeps spindle load within typical workshop limits. Deep-cut capability with proven indexable insert compatibility Designed with a 40 mm cutting length, this tool enables deeper cuts while maintaining chip control and surface finish. Accepting ANHX 1004–1206 indexable inserts means the cutter can be reconditioned quickly by replacing worn inserts rather than the entire body. Indexable systems reduce tooling costs over time: once an insert reaches wear limits it can be rotated or replaced, restoring cutting performance without regrinding. Compatibility with Palbit-specified inserts ensures a wide selection of grades for steel, stainless steel or cast materials where appropriate. Secure clamping for rapid insert changes and reliable performance Insert retention is engineered for workshop efficiency: the cutter uses a Torx T8 drive and M3x7 fixing screws to clamp inserts reliably. Tight, repeatable clamping minimises micro-movement under cutting forces and supports consistent surface finish across multiple setups. The Torx interface reduces the risk of cam-out during torqueing, keeping insert seating precise and facilitating faster tool changes on the shop floor — a practical advantage where downtime costs are significant. Suited to workshop workflows and dependable supply With an overall length of 150 mm and a balanced design, the tool integrates easily into common tool holders and machining centres used in small series production and maintenance shops. The indexable configuration supports quick adaptation to different grades and geometries of inserts, helping workshops maintain throughput without complex retooling. Combined with Metav Werkzeuge’s sourcing and logistics, the cutter is positioned as a practical choice for teams aiming to streamline tooling inventories while retaining machining precision. For secure supply of Teknik Cutting Tools’ S785TM indexable milling cutter and tailored advice on insert grades and clamping, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: S785TM Manufacturer: Teknik Makina Weight: 0.136 kg Facts Shaft diameter: 32 mm Cutting length: 40 mm Overall length: 150 mm Cutting angle: 90° Number of flutes: 4 Special features Compatible with ANHX 1004–1206 indexable inserts Insert supplier fit: Palbit Torx key size: T8 Torx screw: M3x7 FAQ Which inserts fit this cutter? The S785TM accepts ANHX 1004–1206 indexable inserts; the tool is designed for those insert geometries and sizes and is compatible with Palbit-specified grades. Is the cutter suitable for deep shoulder milling? Yes, the 40 mm cutting length and rigid 32 mm shaft make the cutter suitable for deeper shoulder milling where controlled chip evacuation and stability are required. How are the inserts secured and changed? Inserts are secured with an M3x7 screw operated via a Torx T8 key, enabling reliable clamping and quick replacement on the shop floor. Can this tool be used for stainless steel and aluminium? Material suitability depends on the chosen insert grade; the cutter body accepts standard ANHX inserts, so selecting appropriate Palbit grades provides options for stainless steel, aluminium and other materials. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, indexable solution that combines secure clamping and simple insert replacement: the 25 mm shank provides rigidity for stable machining, while compatibility with ANHX 1004–1206 inserts keeps tooling costs down. Order through Metav Werkzeuge or contact our consultants for application advice. Shank cutter for ANHX 1004-1206 indexable inserts (Teknik Makina) — 25 mm shank, 90° cutting angle Shank cutter designed to accept ANHX 1004 indexable inserts for reliable shoulder and face milling in production and workshop environments. 25 mm shank for secure clamping Compatible with ANHX 1004–1206 inserts 90° cutting angle for square shoulder milling Rigidity and consistent cutting results A stable toolholder interface is vital for repeatable machining. The 25 mm shank and substantial 180 mm overall length are engineered to deliver axial stability and reach without compromising rigidity. With a carefully balanced geometry and three cutting edges, this design reduces chatter and maintains tool life, which directly contributes to improved cycle-time consistency and fewer reworks in serial production environments. The result is measurable process reliability and lower scrap rates. Reduced downtime through indexable inserts Indexable tooling offers an immediate productivity advantage by separating cutting edge cost from the tool body. Compatibility with ANHX 1004–1206 indexable inserts allows quick replacement of worn edges without regrinding; replacement is secured with an M3x7 Torx screw tightened using a T8 Torx key, so insert changes are fast and require only basic workshop tools. This approach lowers total tooling expenditure and shortens maintenance intervals, translating into higher uptime on milling centres and smaller job shops alike. Precision for shoulder and face milling A true square shoulder is achieved through the 90° cutting angle, which provides clean, perpendicular faces and consistent corner geometry. That geometry is beneficial when tight form tolerances or mating surfaces are required. The cutter’s three-edge configuration balances material removal and surface finish, so operators can expect both efficient cutting and an improved surface without additional finishing passes in many applications. Workshop-ready dimensions and secure fastening Practical dimensions support flexible use across a range of setups: a 25 mm nominal diameter, 35 mm cutting length, and a compact weight of 0.099 kg keep the assembly agile and easy to index in existing tool systems. Designed for use with inserts from recognised manufacturers such as Palbit, the assembly uses standardised fixing hardware for dependable clamping. For production planners and workshop managers this means straightforward integration into established tool inventories and simplified spare-part management. Contact Metav Werkzeuge for tailored advice on the Teknik Makina shank cutter S784TM, compatible inserts and delivery options to ensure the right configuration for the intended application Technical data Article number: S784TM Manufacturer: Teknik Makina Core dimensions Shank diameter: 25 mm Cutting length: 35 mm Cutting angle: 90° Overall length: 180 mm Number of cutting edges: 3 Diameter: 25 mm Weight: 0.099 kg Special features Compatible with ANHX 1004–1206 indexable inserts Suitable insert manufacturer: Palbit Torx screw: M3x7 Torx key: T8 SKU: S784TM FAQ Which indexable inserts fit this cutter? The Teknik Makina shank cutter S784TM is designed for ANHX 1004–1206 indexable inserts; Palbit sizes within this range are compatible. How are inserts secured in place? Inserts are fixed with an M3x7 Torx screw, using a T8 Torx key for secure and repeatable clamping on the S784TM. What shank diameter and overall length does the tool require? The cutter features a 25 mm shank and an overall length of 180 mm, suitable for standard toolholders that accept a 25 mm dia. shank. How many cutting edges are fitted and what does that mean for finishing? The tool has three cutting edges, which balance material removal rate and surface finish, often reducing the need for secondary finishing operations. Is the cutter suitable for square shoulder milling? Yes — the 90° cutting angle is intended for clean square shoulders and precise face milling applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of ANHX 1004–1206 insert compatibility, a 20 mm shank and a 30 mm cutting length for consistent, productive milling results; order the tool directly via Metav Werkzeuge or consult our specialists for application guidance. Shank cutter S783TM – 20 mm shank, for ANHX 1004–1206 indexable inserts | Teknik Makina A Shank cutter S783TM engineered for indexable-insert milling, offering secure insert clamping and a compact cutting length for precision pocketing and shoulder milling in CNC operations 20 mm shank for rigid toolholding Compatible with ANHX 1004–1206 inserts Three cutting edges for balanced cutting 160 mm overall length for extended reach Consistent performance through insert compatibility The S783TM is designed around the proven ANHX 1004–1206 indexable insert system, ensuring fast insert changes and predictable cutting geometry. Compatibility with Palbit-type inserts simplifies supply chains and reduces tooling variants on the shop floor. With a 90° cutting angle, the tool supports square-shoulder milling and precise face finishes; this combination yields stable forces and repeatable results in series production. The focus on insert interchangeability translates into lower downtime and a predictable cost-per-part for production planners. Rigidity and reach balanced for everyday milling A 20 mm shank provides the rigidity required for consistent chip evacuation and reduced vibration, while the 160 mm overall length gives sufficient reach for medium-depth pockets. The 30 mm cutting length balances tool engagement and stiffness, helping to maintain dimensional accuracy without sacrificing accessibility. The compact mass (approx. 0.058 kg) makes handling and tool changes straightforward, and the geometry supports stable toolholding in common milling arbors and collets, improving surface quality and tool life. Secure clamping and fast service intervals Insert retention is achieved using the supplied fastener configuration: T8 Torx drive and M3x7 screw for reliable seating under cyclic loads. This familiar fastening standard allows for quick, toolroom-friendly maintenance and reduces the learning curve for operators. The cutter’s three cutting edges distribute load evenly, which moderates wear on each edge and extends the interval between insert indexings. As a result, cycle times remain steady and maintenance planning becomes simple and predictable. Integration into workshop workflows Intended for installation in standard CNC toolholders, the cutter integrates smoothly into existing machining processes without the need for special fixtures. The compact design supports efficient nesting of tools in tool magazines and reduces collision risk in tight setups. For procurement and workshop managers, the combination of insert compatibility, standard fastener types and a robust shank offers a pragmatic route to lower tooling complexity and improved throughput in everyday milling operations. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina shank cutter S783TM into production setups — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: S783TM Manufacturer: Teknik Makina Facts Shank diameter: 20 mm Cutting length: 30 mm Overall length: 160 mm Number of cutting edges: 3 Weight: 0.058 kg Cutting angle: 90° Special features For ANHX 1004–1206 indexable inserts Compatible with Palbit insert systems Torx key: T8 Torx screw: M3x7 FAQ Which inserts fit this shank cutter? The cutter is compatible with ANHX 1004–1206 indexable inserts, enabling quick insert swaps and supply-chain alignment with Palbit-style inserts. How is the insert secured on the cutter? Insert retention uses a T8 Torx drive and an M3x7 screw, providing secure seating under milling loads and straightforward maintenance. What advantages do three cutting edges provide? The three cutting edges distribute cutting forces evenly, reducing individual edge wear and helping to maintain consistent surface finish over longer intervals. Can the cutter be used in standard CNC toolholders? Yes; the shank design and dimensions are intended for connection to normal milling arbors and toolholders, facilitating integration into existing tool magazines. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combining a rigid 16 mm shank with compatibility for ANHX 1004–1206 indexable inserts ensures efficient, cost-conscious milling and straightforward insert changes; benefit from a compact 160 mm overall length and secure Torx clamping for reliable workshop performance. Order the S782TM directly via Metav Werkzeuge or consult their specialists for technical guidance and fast supply. Schaftfräser S782TM — Shank milling cutter with 16 mm shank for ANHX 1004–1206 (Teknik Makina) The Schaftfräser S782TM is a precision shank milling cutter designed for use with ANHX 1004–1206 indexable inserts, combining compact dimensions and sturdy clamping for general workshop and production tasks 16 mm shank diameter for standard toolholders Compatible with ANHX 1004–1206 indexable inserts Two cutting edges for effective material removal 160 mm overall length for practical reach Precise indexable milling that reduces tooling costs This indexable-insert cutter is designed to make tooling more economical: by using standard ANHX 1004–1206 indexable inserts the system separates cutting geometry from the body, lowering running costs and enabling quick replacement. The 16 mm shank and standardised insert pocket ensure straightforward integration into existing toolholders, while the two cutting edges provide efficient chip removal and steady material engagement. For shops managing variety in small and medium runs, the modular approach offers reproducible cuts and simplified inventory. Robust design for dependable handling and secure clamping Engineered for consistent performance, the cutter presents a 90° cutting angle and a 160 mm overall length, giving a balance between rigidity and reach. The lightweight body (approx. 0.036 kg) reduces spindle load, and the Torx T8 key with an M3x7 screw secures the insert reliably, lowering the risk of loosening under intermittent heavy cuts. Compatibility with insert manufacturer Palbit ensures access to a wide range of grades and geometries; this aids optimisation for different materials without retooling the shank. Practical workshop benefits and supply reliability Suitable for conventional milling tasks where indexable insert solutions are preferred, this cutter supports efficient workshop workflows and rapid uptime after tool changes. The compact configuration and standardised clamping mean less time on setup and more time cutting, which is particularly valuable in maintenance and small-batch production. Metav’s supply and quality filter for the European market reinforces availability and consistent specification, supporting dependable replenishment and reduced procurement complexity. For reliable milling performance choose the Teknik Makina S782TM shank milling cutter and secure procurement through Metav Werkzeuge — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice and swift delivery. Technical Data Article number: S782TM Manufacturer: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Facts Weight: 0.036 kg Shank diameter: 16 mm Cutting length: 25 mm Cutting angle: 90° Diameter: 16 mm Overall length: 160 mm Cutting edges: 2 Special features Suitable for ANHX 1004–1206 indexable inserts Compatible insert manufacturer: Palbit Torx key: T8 Torx screw: M3x7 SKU: S782TM FAQ Which indexable inserts fit this cutter? The S782TM is designed for ANHX 1004–1206 indexable inserts, allowing use of standard Palbit insert geometries for varied machining tasks. What is the shank diameter and overall length? Shank diameter is 16 mm and the overall length is 160 mm, specified for integration with common toolholders and moderate reach requirements. How many cutting edges does the tool have and what is the cutting angle? The cutter has 2 cutting edges and a 90° cutting angle, suited to straightforward milling operations and reliable chip evacuation. What clamping hardware is used to secure the insert? The insert is secured with a Torx T8 drive and an M3x7 screw, providing stable fixation for machining forces. Is the S782TM suitable for small-batch production and workshop maintenance? Yes — the modular insert system and compact shank make the S782TM well suited to small-batch production, maintenance work and situations where quick insert changes improve uptime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise insert compatibility, a compact 32 mm cutting diameter and a robust 25 mm shank for consistent, low‑vibration milling results; order the tool directly via Metav Werkzeuge or consult the technical advisors for application guidance. S763TM shank cutter – 32 mm diameter, for ANHX 1004–1206 indexable inserts (Teknik Makina) S763TM is a purpose-built shank-mounted milling cutter intended for indexable‑insert milling, offering secure insert clamping and straightforward maintenance for workshop and production use 32 mm cutting diameter 25 mm shank diameter 40 mm cutting length Compatible with ANHX 1004 inserts Built for stable, repeatable cutting in production The S763TM is engineered to deliver consistent machining through its 3 cutting edges and a 90° cutting angle, which together provide an even load distribution and predictable engagement. These geometric choices reduce chatter and support repeatable tolerances across batches, making the cutter suitable for serial production as well as precise one‑off work. The assembly is optimised for indexable‑insert workflows, allowing the milling head to maintain cutting stability during extended runs. Fast insert changes and reduced downtime Designed with practical shop routines in mind, the tool uses a M3x7 Torx screw and accepts a T8 key for secure insert fixation. The 25 mm shank and a 125 mm overall length create a compact, rigid setup for milling heads, while the 40 mm cutting length balances reach and stiffness. Quick insert replacement reduces machine downtime, and the clear mechanical interface with ANHX 1004 indexable inserts simplifies tool maintenance and inventory management for production planners and maintenance staff. Suited to workshops and industrial environments This cutter was developed for users seeking reliable insert milling with established indexable systems; it is compatible with inserts from Palbit and addresses the needs of both trade workshops and industrial shops that demand reproducible results. The tool’s moderate weight of 0.783 kg and straightforward geometry facilitate handling during tool changes and set‑up, while the robust shank supports stable cutting forces in routine machining tasks. For buyers looking for a dependable insert milling solution, the S763TM represents a pragmatic balance of performance and serviceability. Order the Teknik Makina S763TM shank cutter through Metav Werkzeuge for guaranteed supply from Emmerich and expert application advice—contact info@metav-werkzeuge.com or call +49 2822 7131930 for detailed support Technical data Article number: S763TM Manufacturer: Teknik Makina Suitable for inserts: ANHX 1004–1206 (Palbit) Facts Diameter: 32 mm Shank diameter: 25 mm Cutting length: 40 mm Number of cutting edges: 3 Overall length: 125 mm Weight: 0.783 kg Cutting angle: 90° Torx screw: M3x7 Torx key: T8 Special features Designed for ANHX 1004 indexable inserts Compatible with Palbit inserts 3‑flute design Secure Torx clamping Compact, rigid shank FAQ What types of inserts fit this cutter? The S763TM accepts ANHX 1004–1206 indexable inserts and is listed as compatible with Palbit insert variants. How is the insert secured in the milling head? Insert clamping is accomplished with a M3x7 Torx screw; the recommended tightening tool is a T8 key for correct seating and repeatable clamping force. What are the key dimensions for setup and tool holders? Key dimensions include a 32 mm cutting diameter, 25 mm shank diameter and 125 mm overall length, which assist in selecting appropriate tool holders and setting stick‑out. Is the cutter suitable for serial production runs? Yes, the combination of 3 cutting edges and a 90° cutting angle provides stable cutting behaviour that suits repetitive production tasks and helps preserve surface quality across batches. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, indexable design that combines secure clamping and rapid insert changes for uninterrupted milling performance; the combination of a 25 mm cutting diameter, 20 mm shank and reliable Torx clamping reduces setup time and supports steady cuts—order directly via Metav Werkzeuge or consult the sales team for application advice. Shank cutter S762TM — indexable shank cutter, 25 mm diameter, TekNik Makina The Shank cutter S762TM is a robust indexable cutter designed for face and shoulder milling with ANHX 1004–1206 indexable inserts, offering a compact profile for general machining and industrial workshop use. 25 mm cutting diameter Compatible with ANHX 1004 inserts Three cutting edges for stable cuts 20 mm shank with Torx M3x7 fastening Consistent chip control for reliable milling results A tool engineered for stability and predictable performance, the S762TM combines a 25 mm cutting diameter with three cutting edges and a 90° cutting angle to deliver clean shoulder cuts and reduced vibration. The indexable-insert concept separates the cutting geometry from the shank, so the cost of wear is limited to inserts alone. For operations where repeatability matters, this configuration encourages consistent chip formation and surface finish while keeping per-cut costs lower than solid-carbide alternatives. Fast insert changes and secure clamping to reduce downtime Changeovers are simplified by the Torx clamping hardware: a M3x7 screw secured with a T8 Torx key ensures a positive, repeatable seat for each insert. The cutter accepts ANHX 1004–1206 indexable inserts (compatible with Palbit types), enabling rapid replacement and flexible selection of grades for different workpiece demands. A 20 mm shank gives rigid support in standard toolholders, while the 35 mm cutting length and 155 mm overall length provide the reach and clearance required for many milling set-ups. Built for everyday production with focused serviceability Weighing 0.432 kg, this indexable shank cutter balances mass for stable rotation without excess bulk, aiding toolholder balance and tool-change ergonomics. The modular nature of the design means wear is confined to inserts, which supports predictable tool-stock management and straightforward maintenance planning. For workshops aiming to streamline tooling stocks, the S762TM offers a practical mix of serviceability and performance that aligns with routine production schedules. For detailed application guidance or to arrange supply direct from Metav Werkzeuge in Emmerich—relying on our European stock and consultation service—please contact Metav Werkzeuge for tailored recommendations and order facilitation Technical data Article number: S762TM Manufacturer: Teknik Makina Designation: Shank cutter for ANHX 1004-1206 indexable inserts SKU: S762TM Facts Cutting diameter: 25 mm Shank diameter: 20 mm Cutting length: 35 mm Overall length: 155 mm Weight: 0.432 kg Number of cutting edges: 3 Cutting angle: 90° Special features Compatible inserts: ANHX 1004–1206 Insert compatibility: Palbit Clamping screw: M3x7 Torx key size: T8 Indexable insert system for reduced running costs FAQ Which inserts fit this shank cutter? The shank cutter S762TM is designed for ANHX 1004–1206 indexable inserts; Palbit-compatible grades are suitable for a range of machining tasks. How is the insert secured? Each insert is fastened with an M3x7 Torx screw tightened with a T8 key, providing a secure and repeatable clamping interface for the S762TM. What are the key dimensions for holder selection? Key dimensions include a 20 mm shank diameter, 25 mm cutting diameter, 35 mm cutting length and 155 mm overall length; these values guide toolholder and machine setup. How many cutting edges does the cutter have? This indexable shank cutter features three cutting edges, offering a balance between material removal rate and stability. Is the cutter suitable for repetitive production work? Yes—its indexable-insert design and compact mass (0.432 kg) make the S762TM suitable for routine production where quick insert changes and predictable tool costs are important. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, indexable-insert cutter that combines firm clamping with a long effective cutting reach; the design delivers consistent chip control and reliable repeatability across series production. Order directly via Metav Werkzeuge or consult the Metav specialists for process-matched recommendations. Shank Cutter S776TM – Indexable-insert cutter, 20 mm shank, 30 mm cutting length (Teknik Cutting Tools) The Shank Cutter S776TM is a robust cutter body designed for milling with ANHX-series indexable inserts; it suits light to medium-duty roughing and finishing tasks in workshop and production settings. 20 mm shank diameter for secure clamping 30 mm effective cutting length Compatible with ANHX 1004-1206 inserts Torx fixing screw M3x7 with T8 key Stable clamping for repeatable results The central benefit of a 20 mm shank diameter is improved toolholder stability. A stiffer connection between spindle and tool significantly reduces vibration, which leads to more consistent surface finishes and longer insert life. The cutter's design keeps the insert seat rigid so that each pass maintains geometry; when paired with high-quality holders, the result is repeatable production rather than occasional rework. Efficient machining with an indexable system Equipped for ANHX 1004-1206 indexable inserts, the cutter enables rapid insert changes and predictable cutting behaviour. The two-flute configuration with a 90° cutting angle provides a balance between chip evacuation and axial engagement, so material removal remains efficient without excessive radial loading. For operations where setup time and tool-change speed matter, this approach reduces non-productive time and supports consistent cycle times. Practical compatibility and straightforward service Compatibility with inserts from Palbit and the supplied Torx fixing arrangement (screw M3x7, key T8) simplifies procurement and maintenance. The fixing system is familiar to workshop technicians and allows secure clamping of the insert with minimal torque. Regular inspection and correct screw torque restore clamp integrity quickly, offering low-maintenance uptime and predictable performance per shift. Designed for workshop-to-light-production environments With an overall length of 100 mm and a compact mass of 0.247 kg, the tool body is sized for flexible use in smaller spindles and manual setups as well as automated cells. The 30 mm cutting length grants a comfortable axial reach for stepped pockets and shoulder milling while keeping deflection low. For shops consolidating tool inventories, the indexable approach reduces total tooling costs by extending insert life and simplifying regrinding needs. Why this cutter benefits process planners By combining a stiff shank, an indexable-insert concept and straightforward fixing hardware, the configuration favours predictable machining results and easier tool management. Process engineers will value the ability to standardise on a cutter body that accepts widely available ANHX inserts, which streamlines stockkeeping and shortens procurement lead times. For tailored advice and procurement support from Metav Werkzeuge—rely on our specialists in Emmerich to match the S776TM to the machining task and to supply inserts or holders that suit the application. Technical data Article number: S776TM Manufacturer: Teknik Makina Brand: Teknik Cutting Tools Compatible inserts: ANHX 1004-1206 Indexable Inserts Suitable insert maker: Palbit Facts Shank diameter: 20 mm Cutting length: 30 mm Overall length: 100 mm Number of cutting edges: 2 Weight: 0.247 kg Cutting angle: 90° Special features Torx fixing screw M3x7 Torx key size T8 For ANHX 1004 inserts Indexable-insert cutter body Compact, production-capable design FAQ What insert types fit this cutter? The cutter accepts ANHX 1004-1206 indexable inserts; compatibility is stated for ANHX 1004 series and extended sizes in the ANHX family. Is the shank diameter suited to standard collets and holders? Yes, the 20 mm shank diameter matches common 20 mm toolholders and collets, providing secure clamping for improved stability. How is the insert secured in the cutter body? Inserts are retained with a Torx fixing screw M3x7; the required key is T8, enabling quick and secure insert changes. Can this cutter be used for finishing operations? With its two-flute geometry and 90° cutting angle, the cutter is suitable for light finishing as well as roughing, depending on cutting data and insert grade. Which manufacturers supply compatible inserts? Palbit is listed as a compatible insert manufacturer; the cutter is designed to work with ANHX-format inserts from established suppliers. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from a 16 mm shank and a 90° cutting geometry combined with fast indexable-insert changes; the two-edge design provides efficient material removal and low vibration for consistent shoulder milling. Order the shank milling cutter directly via Metav Werkzeuge or ask our consultants if required. Shank milling cutter S775TM – 90° cutter, Ø16 mm, for ANHX 1004-1206 indexable inserts (Teknik Makina) Shank milling cutter S775TM for precision shoulder milling with ANHX-series indexable inserts, designed for rigid toolholding and reliable insert clamping in industrial machining applications. 90° cutting angle for precise shoulder milling 16 mm shank diameter for rigid toolholding Compatible with ANHX 1004-1206 indexable inserts Secure clamping with M3x7 Torx screw, T8 key Stable rigidity for repeatable shoulder milling The combination of a 16 mm shank and a compact overall length delivers a stable cutting platform that reduces deflection and improves dimensional consistency. With a true 90° cutting geometry the tool produces square shoulders and clean part faces, translating the cutter’s mechanical stability into predictable cycle times and reduced rework. For operations where positional accuracy and surface integrity matter, the robust shank helps maintain cutting parameters and extend effective tool life. Fast insert changes and proven compatibility Designed for ANHX-series tooling, the holder accepts ANHX 1004-1206 indexable inserts and pairs with inserts from Palbit, enabling rapid plate replacement and minimal downtime. The clamping system uses an M3x7 Torx screw and a T8 key for secure fixation, ensuring repeatable seating without complicated procedures. Quick access to the insert seat reduces non-productive time and supports lean production workflows, making the cutter suitable for batch and series machining where fast tool swaps are essential. Efficient cutting with low vibration and serviceability Equipped with two cutting edges, the cutter balances material removal rate and surface finish, delivering efficient machining for shoulder and face operations. The specified cutting length of 25 mm provides ample engagement for many common pocketing and profiling tasks without sacrificing stiffness. Lightweight at 0.14 kg, the tool is easy to handle during set-up yet engineered to minimise chatter under appropriate machining parameters, supporting consistent surface quality and longer insert life. Contact Metav Werkzeuge for a tailored quote and to confirm compatibility with specific inserts or toolholders; available from stock in Emmerich – eMail: info@metav-werkzeuge.com or Tel: +49 2822 7131930 Technical data SKU: S775TM Product name: Shank milling cutter Designation: for ANHX 1004-1206 Indexable Inserts Manufacturer (raw data): Teknik Makina Facts Shank diameter: 16 mm Cutting length: 25 mm Overall length: 90 mm Weight: 0.14 kg Cutting angle: 90° Number of cutting edges: 2 Special features Compatible insert series: ANHX 1004-1206 Compatible insert manufacturer: Palbit Clamping screw: M3x7 Torx Torx key size: T8 Application: shoulder milling / indexable insert system FAQ Which inserts fit this cutter best? The S775TM shank milling cutter is specified for ANHX 1004-1206 indexable inserts; inserts from Palbit are explicitly compatible with this holder. How is the insert secured on the cutter? Insert fixation is achieved with an M3x7 Torx screw tightened using a T8 key, providing secure and repeatable clamping for the ANHX plates. What diameter and length does the shank provide? The tool features a 16 mm shank diameter with a cutting length of 25 mm and an overall length of 90 mm, offering a balance of rigidity and reach. How many edges does the cutter use and what is the benefit? The holder utilises two cutting edges, which allows efficient material removal while maintaining good surface finish and manageable cutting forces. Is the S775TM suitable for heavy interrupted cuts? The robust 16 mm shank and secure clamping reduce deflection risk; for heavy interrupted cuts, appropriate insert geometry and cutting parameters are recommended to match the application. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com