Klemmhalter 93° SVJCR 2525 M11-IK for VCMT 1103 Indexable Inserts Innenkühlung Rechtsschneidend - Teknik Makina

Take advantage of a robust combination of precise fit, internal coolant and compatibility with VCMT 1103 indexable inserts to improve cycle stability and reduce rework. The holder’s 25 x 25 mm shank and 93° cutting angle provide consistent chip control and repeatable seating. Order the SVJCR 2525 clamping holder directly via Metav Werkzeuge or ask our consultants if needed.

SVJCR 2525 clamping holder — right‑hand toolholder with internal coolant by Teknik Makina

The SVJCR 2525 clamping holder is a right‑hand turning toolholder designed for VCMT indexable inserts, featuring internal coolant delivery and a sturdy 25 x 25 mm shank suitable for production turning operations

• Internal coolant delivery
• Compatible with VCMT 1103 inserts
• 25 x 25 mm robust shank
• Right‑hand, 93° cutting angle

Improved coolant flow for stable cutting performance

The integrated internal coolant channel directs cutting fluid precisely to the cutting edge, reducing heat at the tool–workpiece interface and promoting longer tool life. For shops that run continuous turning cycles, targeted coolant reduces thermal deformation and lowers the risk of built‑up edge. The design is particularly effective when paired with VCMT 1103 inserts, where coolant access directly behind the insert improves chip evacuation and flank wear behaviour. This technical arrangement results in fewer interruptions for regrinding or insert changes and helps maintain consistent surface finish in serial production.

Secure clamping and precise seating for repeatable results

A well engineered clamping seat and Torx M2.5×6.5 fastening ensure reliable insert retention under interrupted cuts. The SVJCR 2525 holder’s 25 x 25 mm shank and 32 mm cutting‑head width provide a rigid interface with modest overhang, reducing vibration and improving dimensional stability. The assembly, tightened with a T8 key, is designed so that the insert is held with repeatable orientation; this means setup time is minimised and component tolerances are easier to hold across batches. For operators new to indexable tooling, the concept is simple: a precise seat plus secure clamp equals consistent cut geometry.

Application focus: right‑hand turning with predictable chip control

Engineered for right‑hand turning, the holder features a 93° approach angle that balances radial and axial forces for a controlled cut. The 40 mm cutting height and overall length of 150 mm are optimised for general turning tasks where rigidity and accessibility are required. At a weight of 0.63 kg, the toolholder is robust yet manageable for rapid tool changes. When machining a range of ferrous and non‑ferrous materials, the combination of geometry and internal coolant supports predictable chip form and reduces cycle variability, which is a rational way to lower scrap rates and increase throughput.

Contact Metav Werkzeuge to confirm compatibility with existing toolposts and to arrange delivery of the Teknik Makina SVJCR 2525 clamping holder from Emmerich

Technical data

• Article number: AP522TM
• Manufacturer: Teknik Makina
• ISO designation: SVJCR 2525
• For inserts: VCMT 1103

Facts

• Shank width: 25 mm
• Shank height: 25 mm
• Cutting‑head width: 32 mm
• Cutting height: 40 mm
• Overall length: 150 mm
• Overall height: 25 mm
• Cutting angle: 93°
• Weight: 0.63 kg
• ECLASS: 21181004
• Cutting direction: right

Special features

• Internal coolant delivery
• Torx screw: M2.5x6.5
• Torx key size: T8
• Compatible with VCMT indexable inserts
• Holder shank designation: M11‑IK

FAQ

What inserts are compatible with this clamping holder?
The holder is designed for VCMT 1103 indexable inserts and provides the correct seating and clamping geometry for reliable performance with those grades.

Is coolant delivered through the holder?
Yes — the toolholder features internal coolant delivery to the insert area for improved thermal control and chip evacuation.

Which cutting direction is this toolholder made for?
This is a right‑hand turning holder with a 93° approach angle, intended for standard right‑hand turning applications.

What is the ISO designation and weight of the toolholder?
The ISO designation is SVJCR 2525 and the toolholder weighs 0.63 kg (SKU AP522TM by Teknik Makina).

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com