Klemmhalter 93° SDJCR 1616 H07-IC For DCMT 0702 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina

Benefit from the combination of stable clamping and internal coolant plus a compact 100 mm overall length for flexible workshop use; these features contribute to secure insertion retention and improved chip control during right-hand turning. Order the SDJCR 1616 clamp holder directly via Metav Werkzeuge or contact our consultants for application advice.

SDJCR 1616 SDJC Clamp holder for DCMT indexable inserts — right-hand, internal coolant

Clamp holder for right-hand turning, compatible with DCMT 0702 indexable inserts and designed for secure clamping in industrial turning applications

• SDJCR 1616 ISO designation, right-hand
• Internal coolant for improved chip evacuation
• Compatible with DCMT 0702 indexable inserts
• 100 mm overall length, 16 x 16 mm shank

Precision clamping that stabilises every cut

The SDJCR 1616 toolholder is engineered to provide secure clamping and consistent repeatability in turning cycles. With a 16 x 16 mm shank and a 20 mm cutting-head width, the holder reduces vibration and runout, which translates into improved surface finish and tighter dimensional tolerances. The modest mass (0.21 kg) keeps inertial loads low while the specified cutting height of 27 mm ensures correct insert seating for predictable engagement. These attributes make the holder suitable for both repetitive production runs and precision workshop work, where stability and repeatable results matter.

Internal coolant improves chip evacuation and insert life

Equipped with internal coolant, the holder channels cutting fluid directly to the cutting zone to aid chip evacuation and temperature control. This targeted coolant delivery helps to reduce thermal load on the insert and workpiece, often allowing higher cutting speeds and longer insert life without compromising surface integrity. For operations that demand consistent finish and extended tool life, the internal coolant option provides an immediate, measurable benefit by lowering the risk of built-up edge and reducing the need for frequent insert changes.

Simple assembly and broad compatibility for efficient setup

Compatibility with DCMT 0702 indexable inserts makes this clamp holder a practical choice for many turning applications. The assembly uses a M2.5×5.5 Torx screw and a T8 Torx key, enabling secure, quick insert changes and straightforward maintenance routines. With a 100 mm overall length and a 93° cutting angle, the holder is optimised for right-hand cutting directions and integrates easily into existing setups that accept the H07-IC boring-bar designation. The compact form factor supports accessibility in tight work areas and contributes to predictable tool geometry for a wide range of turning tasks.

Discuss the SDJCR 1616 clamp holder with Metav Werkzeuge for tailored recommendations and reliable supply from Emmerich — contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930

Technical Data

• Article number: AP561TM
• Manufacturer: Teknik Makina
• Model / designation: SDJCR 1616
• Product type: SDJC for DCMT indexable inserts
• Weight: 0.21 kg

Facts

• Shank width: 16 mm
• Shank height: 16 mm
• Cutting-head width: 20 mm
• Cutting height: 27 mm
• Overall length: 100 mm
• Cutting angle: 93°
• Cutting direction: right

Special features

• Internal coolant: yes
• Compatible inserts: DCMT 0702
• Fastening: M2.5×5.5 Torx screw
• Key required: T8 Torx
• Boring-bar designation: H07-IC

FAQ

Which inserts fit this holder best?
The clamp holder is designed for DCMT 0702 indexable inserts, offering correct geometry and stable seating for the intended insert form.

Does the holder provide coolant directly to the cutting zone?
Yes — the SDJCR 1616 clamp holder features internal coolant to support chip evacuation and thermal control at the insert cutting edge.

Is this a right-hand or left-hand toolholder?
This model is configured for right-hand cutting and has a 93° cutting angle suitable for standard right-hand turning operations.

What fastening hardware is required to secure the insert?
The insert is secured with a M2.5×5.5 Torx screw; a T8 Torx key is used for tightening and removal, simplifying insert changes.

For which applications is this holder most suitable?
The clamp holder (Teknik Makina, SKU AP561TM) is ideal for general turning in production and workshop environments where robust clamping, internal coolant, and compact overall length are beneficial.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com