16mm SDJC 1616 SDJC For DCMT 0702 Indexable Inserts, Internal Cooling, Left-Hand Cutting, 93° - Teknik Makina

Take advantage of a left-hand clamping system with internal coolant and secure retention for DCMT 0702 inserts — offering stable machining, straightforward insert changes and reliable shop-floor performance; order the SDJCL 1616 clamping holder directly via Metav Werkzeuge or ask the consultants for integration guidance.

SDJCL 1616 SDJC clamping holder for DCMT inserts — left-hand, internal coolant (Teknik Makina)

The SDJCL 1616 SDJC clamping holder is a left-hand turning toolholder designed for DCMT 0702 indexable inserts, combining compact dimensions with an internal coolant feed for improved chip control and tool life

• Left-hand cutting orientation
• Internal coolant feed
• Compatible with DCMT 0702 inserts
• ISO designation SDJCL 1616

Stable cutting performance for repeatable turning

The holder delivers a stable clamping solution with a tool shank height and width of 16 mm, ensuring consistent seating and minimal vibration during left-hand operations. Compatibility with DCMT 0702 inserts provides a widely available insert format for varied turning tasks, while the 93° cutting angle supports predictable chip flow and reliable surface finish. This combination reduces setup variability and supports efficient production cycles by maintaining consistent cutting geometry.

Coolant-fed design to extend insert life and improve finishes

An integrated internal coolant channel supplies lubricant and coolant directly to the cutting edge, lowering cutting temperatures and aiding chip evacuation. The coolant-fed arrangement helps to extend tool life, reduce built-up edge formation and stabilise surface quality on batch work. For workshops seeking measurable improvements in cycle stability and repeatability, the internal coolant capability delivers a technical advantage over externally cooled setups, particularly on longer runs or tougher materials.

Fast, shop-compatible mounting and secure retention

Engineered for practical use on the shop floor, the holder uses a Torx M2.5x5.5 clamping screw with a T8 key for straightforward insert changes and secure retention. The assembly has an overall length of 100 mm, a cutting-head width of 20 mm and a compact mass of 0.21 kg, balancing rigidity with accessibility in confined toolpost arrangements. Compatibility with the H07-IC boring-bar designation allows simple integration into existing tool inventories while the ISO mark SDJCL 1616 simplifies ordering and replacement management.

Contact Metav Werkzeuge for tailored advice on integrating Teknik Makina SDJCL 1616 clamping holders with internal coolant into existing toolsets and to arrange supply or technical recommendations

Technical data

• Article number: AP566TM
• Designation: SDJC for DCMT Indexable Inserts (SDJCL 1616)
• Manufacturer: Teknik Makina

Core specifications

• Width: 16 mm
• Height: 16 mm
• Cutting-head width: 20 mm
• Overall length: 100 mm
• Total height: 16 mm
• Cutting height: 27 mm
• Weight: 0.21 kg
• Cutting angle: 93°
• Cutting direction: left
• Clamping screw: M2.5x5.5
• Torx key: T8

Features & compatibility

• Internal coolant feed
• Fits DCMT 0702 inserts
• Boring-bar designation: H07-IC
• ISO designation: SDJCL 1616
• Left-hand turning holder
• Suitable for indexable insert turning

FAQ

Is this holder compatible with DCMT 0702 inserts?
Yes. The SDJCL 1616 is specified for DCMT 0702 indexable inserts and secures them in a left-hand configuration while supplying internal coolant.

Can the same holder be used for right-hand turning?
No. This clamping holder is designed for left-hand cutting; right-hand operations require the corresponding right-hand holder variant.

What are the key dimensions and weight?
Main dimensions: 16 mm width and height, 100 mm overall length, 20 mm cutting-head width; weight approximately 0.21 kg.

Does the toolholder provide internal coolant?
Yes. The design includes an internal coolant channel to direct coolant to the cutting zone, improving tool life and surface finish.

Which screw and key are required for insert changes?
Insert fastening uses a Torx M2.5x5.5 screw and a T8 Torx key for secure, repeatable clamping.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com