16mm SVVCN 1616 H16, For VCMT 1604 Indexable Inserts, 72.5° Schnittwinkel, Innenkühlung Neutral - Teknik Makina

Take advantage of the combination of secure clamping, standard insert compatibility and compact dimensions to improve turning stability and cycle consistency; order directly via Metav Werkzeuge or contact our consultants for application advice.

SVVCN 1616 clamping holder for VCMT 1604 indexable inserts — neutral cutting, 100 mm length (Teknik Makina)

The SVVCN 1616 clamping holder is a compact turning tool holder designed for general turning operations with VCMT 1604 indexable inserts, providing a neutral cutting arrangement for versatile machining tasks.

• SVVCN 1616 profile for secure clamping
• Compatible with VCMT 1604 indexable inserts
• Neutral cutting direction for versatile use
• Compact 100 mm length, lightweight 0.187 kg

Increased process stability through precise clamping

The SVVCN 1616 holder is engineered to deliver repeatable clamping and a defined seating for indexable inserts, which reduces vibration and improves surface finish. The holder’s geometry, combined with a 72.5° cutting angle, supports consistent chip formation and lower tool deflection; this results in fewer in-process adjustments and longer intervals between regrinds. For production environments where stability and reproducibility matter, the secure clamping mechanism translates directly into predictable cycle times and reduced scrap rates.

Broad compatibility with a common insert grade for quicker changeovers

Designed specifically for VCMT 1604 indexable inserts, the holder simplifies tooling logistics and reduces the range of inserts required on the shop floor. The neutral cutting direction allows the same setup to be used across a range of turning tasks, improving flexibility. Insert replacement is straightforward and designed to be performed quickly; the standardised interface means that spare inserts can be stocked economically, lowering total tooling downtime and improving overall throughput.

Compact design that enhances rigidity in tight set-ups

With a 100 mm overall length and a compact cross-section of 16 x 16 mm, the holder minimises overhang and increases rigidity in constrained workspaces. The narrow 8 mm cutting head width and modest mass of 0.187 kg reduce centrifugal loads and make the holder suitable for short-reach operations where chatter and deflection are a concern. Reduced overhang combined with a compact profile makes it easier to maintain tight tolerances close to shoulders and internal features.

Practical specification for consistent workshop results

The tool is supplied in the ISO designation SVVCN 1616 and is identified with the shank designation H16, which supports straightforward integration into existing toolholder inventories. A specified cutting-edge height of 35 mm and the neutral feed orientation are useful for planning fixture clearances and tool-path strategies. The holder’s measured characteristics permit quick calculation of tool stick-out and clamping parameters, enabling machining programmes to be prepared with clarity and fewer on-machine trials.

For reliable turning results with a compact and compatible solution, ask Metav Werkzeuge about the SVVCN 1616 clamping holder (SKU D144TM) to confirm suitability for specific components — call +49 2822 7131930 or email info@metav-werkzeuge.com

Technical data

• Article number: D144TM
• Manufacturer: Teknik Makina
• ISO designation: SVVCN 1616

Facts

• Overall length: 100 mm
• Holder height: 16 mm
• Holder width: 16 mm
• Cutting head width: 8 mm
• Cutting edge height: 35 mm
• Cutting angle: 72.5°
• Weight: 0.187 kg
• Cutting direction: neutral

Special features

• Suitable for VCMT 1604 inserts
• Shank designation H16
• Indexable insert holder

FAQ

Which inserts fit this holder?
The SVVCN 1616 clamping holder is compatible with VCMT 1604 indexable inserts; this match is specified for reliable seating and predictable chip formation when used as intended (SKU D144TM, Teknik Makina).

What cutting direction is recommended?
The holder is configured for a neutral cutting direction, offering versatility for a variety of turning operations and allowing the same set-up to be applied to different part geometries.

Is the holder suitable for tight fixture spaces?
Yes. With a 100 mm overall length and a compact 16 x 16 mm profile, the holder is intended for confined setups where reduced overhang and increased rigidity are needed.

How does the 72.5° cutting angle affect machining?
A 72.5° cutting angle supports stable chip removal and a balanced cutting force vector, which helps reduce tool deflection and contributes to improved surface finish and longer insert life.

What is the weight and how does it influence performance?
Weighing 0.187 kg, the holder’s low mass reduces dynamic loading and helps maintain stability at higher spindle speeds when used within recommended limits.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com