Klemmhalter 93° DDJNR 2525 M11 for DN-- 1104 Wendeplatten Innenkühlung Rechtsschneidend - Teknik Makina

Compact right-hand clamping toolholder combines precise insert seating and robust shank engagement for steady turning performance; its 150 mm length and 93° cutting angle support consistent chip flow and surface finish. Order the holder via Metav Werkzeuge or consult their specialists for application guidance.

DDJNR 2525 clamping toolholder — right-hand, 150 mm (Teknik Makina)

DDJNR 2525 is a right-hand clamping toolholder tailored for DN-- 1104 indexable inserts, engineered to deliver repeatable seating and dependable stability in medium-reach turning operations.

• Right-hand orientation for conventional turning
• ISO designation DDJNR 2525
• Compatible with DN-- 1104 inserts
• Robust 150 mm overall length

Consistent seating for repeatable machining quality

The DDJNR 2525 design focuses on secure insert clamping and predictable tool geometry. With a precise seating interface for indexable inserts DN--1104, the holder minimises micro-movement at the cutting edge, which translates into improved surface finish and reduced scrap rates. The specification is particularly relevant where repeatability across batches is required, because a consistent clamping point reduces the need for frequent re-adjustment and aligns with shop-floor quality control processes.

Geometry that enhances rigidity and chip control

A compact overall length of 150 mm combined with a cutting angle of 93° and a head width of 32 mm gives the toolholder a favourable stiffness-to-reach ratio. The right-hand orientation supports conventional turning setups and encourages effective chip evacuation under typical feed and speed ranges. As a result, cycle-time stability and insert life benefit from less vibration and better heat dispersion — two practical gains that improve throughput and lower tooling costs over time.

Secure mounting and straightforward integration

The holder uses an M11 shank/thread designation (M11) for the clamping interface, ensuring robust engagement in compatible tool posts and adaptors. Its modest mass (approx. 0.751 kg) and a holder height of 25 mm make handling and fixturing simple without compromising rigidity. These attributes reduce setup effort and make the toolholder a reliable component in mixed-production workshops where rapid changeovers and stable fixturing are priorities.

Built for professional turning applications and supply reliability

Carrying the ISO designation DDJNR 2525, the toolholder is prepared for industrial turning contexts that require standardised interfaces and predictable performance. Compatibility with the DN-- 1104 insert family simplifies inventory management and speeds up maintenance procedures. Combined with dependable logistics from the supplier network, the holder supports continuous production rhythms and a pragmatic tool supply strategy.

Contact Metav Werkzeuge in Emmerich to discuss application suitability or to reserve Teknik Cutting Tools' DDJNR 2525 clamping toolholder; phone +49 2822 7131930 or email info@metav-werkzeuge.com

Technical data

• Article number: D168TM
• Manufacturer: Teknik Makina
• Model designation: DDJNR 2525
• SKU: D168TM

Facts

• Overall length: 150 mm
• Weight: 0.751 kg
• Cutting height: 30 mm
• Holder height: 25 mm
• Head width: 32 mm
• Width: 25 mm
• Cutting angle: 93°
• Direction: Right-hand
• Compatible insert: DN-- 1104
• Shank/thread: M11

Special features

• ISO designation DDJNR 2525
• For indexable inserts DN--1104
• Right-hand orientation
• Designed for turning applications

FAQ

Is the holder compatible with DN-- 1104 inserts? Yes. The DDJNR 2525 clamping toolholder is specified for DN-- 1104 indexable inserts and provides the correct seating geometry for those plates.

What is the overall length and how does it affect rigidity? Overall length is 150 mm; this length offers a balance between reach and stiffness, helping to maintain rigidity for typical turning tasks.

Which thread or shank designation is used for mounting? Mounting uses an M11 shank/thread designation to ensure secure fixation in compatible tool posts and adaptors.

What cutting direction does the holder support? The holder is configured for right-hand cutting direction, suitable for conventional right-hand turning operations.

Does the product have an ISO or model designation for ordering? Yes. The holder is listed under DDJNR 2525, which can be referenced alongside SKU D168TM for procurement and inventory control.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com