125mm Toolholder for VER16 Indexable Inserts, 20mm Width/Height, 22mm Cutting Head - Teknik Makina

Take advantage of a robust, precision-ready clamp holder that combines firm clamping, standardised compatibility and straightforward setup for consistent turning performance. The design supports VER16 indexable inserts and a compact 125 mm overall length for reduced overhang and improved rigidity. Order directly via Metav Werkzeuge or consult our specialists for configuration advice.

Klemmhalter VER16 L125mm — Clamp holder for VER16 indexable inserts, 125 mm overall length, Teknik Makina

A Klemmhalter VER16 L125mm engineered as a compact clamp holder for turning operations with VER16 indexable inserts, suited to workshop lathes and small turning centres.

• Secure Torx T15 clamping
• Compatible with VER16 indexable inserts
• 125 mm overall length for reduced overhang
• ISO 2020 designation for standardised fit

Increased machining stability through a compact, standardised design

The clamp holder delivers repeatable rigidity thanks to a compact 125 mm overall length, which reduces cantilever effects and helps maintain cutting stability during interrupted cuts. Intended for metalworking environments where consistent seating of indexable inserts matters, the holder is compatible with VER16 inserts and follows the ISO 2020 designation so replacement parts and inserts from standard ranges fit without adaptation. This standard compatibility reduces setup complexity and supports predictable machining results in both batch production and single-part turning.

Faster clamping and reliable insert retention for reduced downtime

Setup is straightforward: the clamping system uses a M3.5x8.5 mounting screw and a Torx T15 drive, enabling secure torque transmission with minimal cam-out and quick tool changes. The 22 mm cutting head width and 30 mm cutting height increase the contact area between holder and insert, improving lateral support and reducing micro-movements that cause chatter. At approximately 0.385 kg, the toolholder balances mass for rigidity without excessive inertial load on the turret, supporting stable feed rates and consistent surface finish.

Workshop-ready compatibility and straightforward maintenance

Designed for everyday use in industrial and craft workshops, the clamp holder keeps maintenance simple: insert replacement requires only the Torx key, and the standardised geometry means spare parts are widely available. The compact form factor allows installation in constrained turret pockets while preserving secure seating for cutting inserts. The product is listed under SKU D520TM, making ordering and stock checks straightforward for procurement teams. For operations seeking dependable, repeatable clamping performance, this toolholder provides a pragmatic balance of rigidity, serviceability and fit-to-industry standards.

Contact Metav Werkzeuge to confirm compatibility and reserve stock of the Teknik Makina D520TM clamp holder at the Emmerich warehouse: info@metav-werkzeuge.com · +49 2822 7131930

Technical data

• SKU: D520TM
• Label: Klemmhalter VER16 L125mm
• Manufacturer: Teknik Makina
• Product type: Klemmhalter
• ECLASS: 21181004
• ISO designation: 2020

Key measurements

• Overall length: 125 mm
• Clamping width: 20 mm
• Height: 20 mm
• Cutting head width: 22 mm
• Cutting height: 30 mm
• Weight: 0.385 kg

Features and compatibility

• Compatible with VER16 indexable inserts
• Torx drive: T15
• Clamping screw: M3.5x8.5
• SKU reference: D520TM
• Product category: Clamp holder

FAQ

What inserts fit this clamp holder?
The clamp holder is compatible with VER16 indexable inserts; the holder follows the ISO 2020 standard for straightforward insert selection.

Which tool is required to tighten the clamping screw?
A Torx T15 key is specified for the clamping screw (M3.5x8.5) to ensure secure, repeatable seating of the insert in the D520TM.

Is this toolholder suitable for turret mounting on small lathes?
The compact 125 mm overall length and 20 mm clamping width make it suitable for many turret pockets on small to medium turning centres, providing reduced overhang and improved rigidity.

How does the cutting head geometry influence performance?
The 22 mm cutting head width and 30 mm cutting height increase support for the insert, which helps reduce vibration and improves surface finish during typical turning operations.

Can the holder be identified easily for reordering?
Yes — the toolholder is listed as SKU D520TM and labelled Klemmhalter VER16 L125mm for straightforward procurement.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com