DNMG110402-FP5 WEP10C WEP10C Wendeplatten - Walter Tools

Take advantage of the WEP10C cermet grade and the FP5 chipbreaker for consistent edge life and reliable chip control; combined with the rhombic 55° geometry and a 0.2 mm corner radius this insert supports precise finishing and productive turning. Order the insert directly via Metav Werkzeuge or consult the team for application-specific advice at info@metav-werkzeuge.com or +49 2822 7131930

DNMG110402-FP5 WEP10C — Turning insert (Drehwendeschneidplatte) by Walter Tools, Walter Cermet, FP5 chipbreaker

The DNMG110402-FP5 WEP10C is a rhombic 55° turning insert intended for general and finishing turning where consistent edge life and controlled chip formation are priorities

• Walter Cermet grade WEP10C
• FP5 chipbreaker for stable chip control
• Rhombic 55° geometry for versatile turning
• 0.2 mm corner radius for fine finishing

Consistent performance from a cermet grade that extends edge life

The choice of WEP10C cermet provides a stable cutting edge and improved wear resistance compared with conventional grades, which translates into longer tool life and fewer indexings. Cermet combines ceramic hardness with metallic toughness; this balance supports higher cutting speeds and a fine surface finish without excessive flank wear. For operations where repeatable part quality and reduced tool handling deliver cost savings, the WEP10C grade is a rational selection supported by Walter's material concept.

Predictable chip control and geometry for productive turning

The FP5 chipbreaker is designed to promote consistent chip formation under a range of feeds and depths of cut, helping to avoid long, stringy chips and minimising interruptions in the machining cycle. The rhombic 55° shape gives good access to shoulders and profiles while the negative 0° rake angle improves strength at the cutting edge for interrupted cuts. The combination of geometry and chipbreaker supports productive, steady machining and helps to achieve the dimensional and surface requirements expected in precision turning.

Practical application guidance and compatibility notes

This insert is finished with a 0.2 mm corner radius, favouring fine finishing passes and controlled corner strength. The tolerance class M and execution G indicate production-grade consistency suitable for series manufacturing. Material suitability should be verified against the manufacturer's product matrix; the insert is supplied in the Walter Cermet series and the catalogue lists the recommended workpiece materials. For seamless integration into existing toolholders, match the DNMG form factor and clamping system; the insert designation DNMG110402-FP5 identifies the plate geometry and size for straightforward replacement and tooling planning.

Discuss application requirements with Metav Werkzeuge to select the optimal Walter Tools DNMG110402-FP5 WEP10C configuration and ensure a productive setup — contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930

Technical data

• Article number: DNMG110402-FP5-WEP10C-WALTER
• Designation: DNMG110402-FP5 WEP10C
• Series: Walter Cermet
• Grade: WEP10C
• Manufacturer: Walter Tools

Facts

• Insert shape: Rhombus 55°
• Size: 11
• Thickness: 04
• Corner radius: 0.2 mm
• Rake angle: 0° (negative)
• Tolerance class: M

Special features

• Chipbreaker: FP5
• Material: Katalogabhängig
• Execution: G
• Insert type: DNMG110402-FP5
• Series description: Cermet cutting material; check product matrix for material suitability

FAQ

What machining tasks suit this insert best?
The DNMG110402-FP5 WEP10C insert from Walter Tools is suited to general turning and finishing where a cermet grade and an FP5 chipbreaker deliver consistent surface quality and long edge life.

Can the WEP10C grade handle higher cutting speeds?
Yes, the WEP10C cermet grade is formulated to support elevated cutting speeds while maintaining wear resistance, making it appropriate for operations that prioritise surface finish and productivity.

How is chip control achieved with this insert?
Chip control is achieved through the FP5 chipbreaker combined with the rhombic 55° geometry; this pairing promotes short, controllable chips across typical feed ranges.

Which toolholders are compatible with DNMG110402-FP5?
Compatibility follows the standard DNMG insert form factor; use toolholders specified for DNMG geometry and confirm clamping requirements before assembly.

Is the corner radius suitable for roughing?
The 0.2 mm corner radius is optimised for finishing and fine profiling; for heavy roughing, a larger radius or a different insert geometry is recommended.

Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen

Protected trademarks and trade names are the property of their respective owners. Brand names and designations are used solely for explanatory purposes and indicate no association between Metav Werkzeuge and the named manufacturers. The offered item is an original, brand-new product from the stated manufacturer.