40.6 x 32.4 x 3.6 mm Shredder/Granulator Knife For GALA Recycling Machines, 1.3207 EW9Co10 - MetavCUT

Take advantage of the combination of high-alloy 1.3207 EW9Co10 steel, a precision 40.6 x 32.4 x 3.6 mm profile and a fit engineered for GALA machines to secure consistent pellet quality and reduced downtime; order the replacement knife through Metav Werkzeuge or consult our specialists for suitability and stock advice.

MetavCUT Recycling Knife (Granulator) 40.6 x 32.4 x 3.6 mm — 1.3207 EW9Co10 for GALA machines

A MetavCUT Recycling Knife (Granulator) engineered for GALA shredders and pelletisers, delivering precise cuts and low-dust processing for a wide range of plastic feedstocks

• High-alloy 1.3207 EW9Co10 steel
• Precision 40.6 x 32.4 x 3.6 mm profile
• Compatible with GALA shredders and granulators
• Optimised for low dust and uniform granules

Consistent cutting quality for repeatable output

The blade's high-alloy composition (1.3207 EW9Co10) and finely honed edge provide precision cuts that translate directly into homogenous granules and stable downstream processing. In recycling and granulating applications, edge geometry and surface finish determine particle uniformity and dust formation; a correctly specified knife therefore supports better process control and a reduced load on sieves and filters. This results in predictable machine behaviour and fewer interruptions during continuous production.

Extended service life to support continuous runs

Manufactured from a wear-resistant alloy, the knife offers increased durability under abrasive and thermally demanding conditions typical for size reduction of films, pipes and regrind. Longer intervals between tool changes mean less mechanical downtime and a steadier throughput. The design focuses on a balance between hardness and toughness to limit chipping while maintaining cutting performance, so maintenance cycles are extended without compromising cut quality or increasing fine dust generation.

Exact fit and straightforward replacement to save time

With a defined profile of 40.6 x 32.4 x 3.6 mm, the blade is produced to tight tolerances for a precise fit in GALA equipment, eliminating alignment issues that reduce blade life and compromise output. For operators less familiar with granulator tooling, a granulator blade is the component that severs plastic into uniform granules; correct installation prevents uneven wear and vibration. The combination of accurate dimensions and consistent edge geometry simplifies exchange procedures and supports rapid restoration of production parameters.

Secure production continuity with MetavCUT quality — contact Metav Werkzeuge in Emmerich for availability, technical clarification and fast dispatch at info@metav-werkzeuge.com or call +49 2822 7131930

Technical Data

• Article number: GALA--40.6x32.4x3.6-13207-EW9Co10
• Label: Zerkleinerungsmesser / Granuliermesser 40.6 x 32.4 x 3.6 für GALA Maschinen aus 1,3207 EW9Co10
• Manufacturer: MetavCUT

Facts

• Dimension: 40.6 x 32.4 x 3.6 mm

Special features

• Material: 1.3207 EW9Co10
• Suitable for: GALA recycling, shredding and pelletising equipment
• Application: size reduction of plastics to uniform granules, low dust generation

FAQ

What types of plastics can this knife process?
The MetavCUT recycling knife is intended for a broad range of thermoplastics commonly encountered in recycling plants, including films, profiles, pipes and plate materials, enabling consistent size reduction for subsequent reprocessing.

Is this blade compatible with my GALA granulator or shredder?
Yes — the blade is specified for use in GALA recycling and pelletising machinery and is manufactured to fit the dimensions required for standard GALA knife holders.

How does the 1.3207 EW9Co10 material affect performance?
The high-alloy composition provides a combination of hardness and toughness that increases wear resistance while maintaining edge integrity, supporting longer service life and stable cutting performance under abrasive conditions.

Can the blade be re-sharpened or reconditioned?
Reconditioning depends on the extent of wear and the alloy condition; light regrinding may be possible, but full restoration should be assessed by a specialist to preserve the correct edge geometry and dimensional tolerances.

How often should replacement be considered?
Replacement intervals vary with feedstock, contamination levels and operating parameters; monitor cut quality and increase in fines or vibration as indicators that the blade requires attention or exchange.

MetavCUT — Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Wir bieten mit der Marke MetavCUT eine wirtschaftliche Alternative zu Hersteller‑Originalteilen: Unsere prozessoptimierten Verschleißteile sind passgenau, langlebig und speziell für den produktiven Einsatz entwickelt.