GX24-4F600N02FS-F1 WDN10 Wendeplatten - Walter Tools

Take advantage of the combination of PKD wear resistance and an optimised 4F600N02FS-F1 chipbreaker for reliable, long-running turning of abrasive non‑ferrous materials. Benefit from the Walter Tools production standard and reduce tool changes through extended service intervals. Order the GX24-4F600N02FS-F1 WDN10 directly via Metav Werkzeuge or ask our consultants if needed.

GX24-4F600N02FS-F1 WDN10 indexable turning insert by Walter Tools — PKD grade, 4F600N02FS-F1 chipbreaker

The GX24-4F600N02FS-F1 WDN10 is an indexable turning insert designed as a high‑wear solution for precision machining of abrasive, non‑iron materials where polycrystalline diamond performance is required

• PKD grade WDN10 for high wear resistance
• Optimised chipbreaker 4F600N02FS-F1
• Designed for abrasive non‑ferrous materials
• Walter Tools quality and consistency

Longer tool life for abrasive non‑ferrous machining

The insert uses polycrystalline diamond (PKD) in the WDN10 grade, a material choice that provides exceptional wear resistance when machining abrasive, non‑iron substrates. Polycrystalline diamond is significantly harder than conventional cemented carbides, which translates into slower flank and rake wear under abrasive cutting conditions. For workshops processing high volumes of aluminium alloys with abrasive inclusions or non‑ferrous composites, this results in fewer insert changes and a smoother production flow. The material behaviour of PKD also supports consistent dimensional stability over extended runs, reducing downstream rework and improving overall process efficiency.

Stable chip control and consistent surface finish

The integrated 4F600N02FS-F1 chipbreaker geometry is engineered to control chips reliably during turning, promoting predictable evacuation and more consistent cutting forces. Controlled chip formation lowers the risk of built-up edge and helps to maintain a steady cutting profile, which benefits surface quality and repeatability. Combined with the PKD cutting edge, the geometry aims to deliver reproducible results in finishing and semi‑finishing operations. For manufacturers prioritising stable cycle times and reduced scrap rates, this insert contributes directly to a measurable improvement in process stability and part quality.

Practical application guidance and productivity gains

As an indexable turning insert optimised for abrasive, non‑ferrous materials, the GX24-4F600N02FS-F1 WDN10 is best applied where traditional carbide wear limits cycle length. The grade is particularly suited to abrasive aluminium alloys, non‑ferrous composites and other difficult, non‑iron workpieces; however, suitability should be checked against the specific product matrix and component requirements. Implementing the insert can reduce downtime for tool changes and lessen the frequency of regrinds or replacements, delivering clear productivity benefits. Trial cuts under representative machining conditions are recommended to determine optimal feeds and speeds for the intended application.

For demanding non‑ferrous turning tasks choose the PKD‑grade GX24-4F600N02FS-F1 WDN10 from Walter Tools — contact Metav Werkzeuge for technical advice or to place an order at info@metav-werkzeuge.com or call +49 2822 7131930

Technical Data

• Article number: GX24-4F600N02FS-F1-WDN10-WALTER
• SKU: GX24-4F600N02FS-F1-WDN10-WALTER
• Product type: indexable turning insert
• Designation: GX24-4F600N02FS-F1 WDN10

Facts

• Grade: WDN10
• Series: Walter Schneidstoffsorte - Serie offen
• Chipbreaker: 4F600N02FS-F1

Special features

• Cutting material: PKD (polycrystalline diamond)
• Material base: catalogue-dependent
• Intended use: abrasive, non‑ferrous materials
• Manufacturer: Walter Tools

FAQ

What materials is this insert intended for? The GX24-4F600N02FS-F1 WDN10 insert is specified for abrasive, non‑iron materials and non‑ferrous alloys where PKD offers superior wear resistance.

What does the WDN10 grade mean in practice? WDN10 denotes a Walter Tools PKD grade with emphasis on wear resistance for abrasive applications; it supports longer tool life and more consistent results in demanding non‑ferrous turning.

How does the 4F600N02FS-F1 chipbreaker improve machining? The 4F600N02FS-F1 geometry promotes reliable chip formation and evacuation, reducing the likelihood of built‑up edge and improving surface finish and process repeatability.

Can this insert be used for finishing operations? Yes, with the correct machining parameters the PKD cutting edge and chipbreaker combination is suitable for finishing and semi‑finishing of abrasive non‑ferrous workpieces.

How should selection be confirmed for a specific component material? Selection should be confirmed against the product matrix and by performing representative trial cuts to establish the optimal feeds and speeds for the workpiece material.

Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen

Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is an original, factory‑new product from the manufacturer Walter Tools.