Durable indexable inserts for efficient metalcutting
Indexable inserts are hardened cutting elements designed to deliver consistent material removal in metalworking, providing cost-effective tool life management and repeatable results for turning, milling and drilling operations. Suited for machining steel, stainless and heat-resistant alloys, these inserts offer rapid edge renewal and reduced downtime through simple indexing, while versions optimised for internal coolant significantly improve chip control and thermal management in demanding applications. By choosing the right insert grade and geometry you gain improved tool life, predictable wear behaviour and better surface finish thanks to enhanced chip control, with key benefits including wear-resistant carbide, internal coolant compatibility and reliable chip breaking.
CCGT 09T302 SH7025 Wendeplatten - Tungaloy
Take advantage of the reliable combination of SH7025 coated carbide and precise geometry for consistent cutting performance and predictable tool life; order through Metav Werkzeuge or request tailored advice if assistance is required. CCGT09T302 SH7025 ISO rhombic turning insert for turning — Tungaloy CCGT09T302 SH7025 is a rhombic ISO turning insert designed for external and internal turning, featuring a 7° clearance angle and an 80° included angle for stable engagement and predictable cutting behaviour ISO rhombic insert, 80° included angle Coated carbide grade SH7025 for toughness 0.2 mm corner radius for precise profiling Cylindrical hole with single-side countersink Consistent cutting performance under variable conditions The combination of SH7025 and coated carbide construction delivers a balance of toughness and wear resistance that promotes edge stability during intermittent cuts and mixed engagement situations. The grade is formulated for turning tasks where small toolholders or changing cutting depths are used, reducing the frequency of unexpected edge failures. As a result, process reliability increases and cycle-time variation is minimised, supporting a more predictable production flow. Clear mounting geometry and what it means for setup Compatibility follows ISO norms and is governed by form, 7° clearance, tolerance class, mounting, size and thickness. The rhombic plate form with an 80° included angle and a cylindrical hole with a single-side countersink (40°–60°) simplifies secure clamping and repeatable positioning. With a plate thickness of 3.97 mm and a 0.2 mm corner radius, the geometry supports accurate profiling and robust seat contact; the single-sided chipbreaker concentrates chip control on the active face, which aids evacuation and stability in both external and internal turning applications. Operational advantages and application guidance Designed for turning operations, this insert provides a practical route to consistent surface finish and extended service intervals when matched to the correct chipbreaker and cutting parameters. The single-sided chipbreaker assists with controlled chip formation in a range of chip loads, while the coated carbide body withstands common turning stresses. For best results, select a chipbreaker and the correct cutting data to match workpiece material and machine rigidity — this approach transforms the insert’s technical properties into measurable shop-floor gains, such as reduced setup time and fewer tool changes, yielding better throughput and increased confidence in daily production. For machining advice and availability of the Tungaloy CCGT09T302 SH7025 insert, contact Metav Werkzeuge for personalised recommendations at info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 6967448 SKU: 6967448-Tungaloy Manufacturer SKU: TUN6967448 Manufacturer: Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Designation: CCGT09T302 SH7025 Facts Size designation: 09 Included angle: 80° Clearance angle: 7° Corner radius: 0.2 mm Plate thickness: 3.97 mm Hole: with hole Hole style: cylindrical hole + single-side countersink (40°–60°) Special features ISO-standard rhombic insert Coated carbide grade SH7025 Single-sided chipbreaker Suitable for external and internal turning Compatibility determined by form, clearance, tolerance, mounting, size and thickness Recommended for small-tool applications and varying engagement conditions FAQ Is the insert suitable for internal turning operations? The rhombic geometry and the cylindrical hole with countersink make the insert suitable for both external and internal turning when used with the correct holder and mounting hardware; the CCGT09T302 SH7025 insert is designed for such versatile use. What advantages does the SH7025 grade offer compared with uncoated carbide? SH7025 is a coated carbide grade that provides improved toughness and edge stability over uncoated grades, making the insert more resilient in variable engagement and when small tools are employed. How does the 0.2 mm corner radius affect component finish? A 0.2 mm corner radius delivers precise profiling capability and helps achieve consistent surface finish on small feature radii while balancing strength at the cutting edge. Which holder characteristics must match the insert? Compatibility requires matching the insert form, 7° clearance, tolerance class, mounting arrangement, size and thickness to the holder or boring bar to ensure correct seating and secure clamping. Can the insert’s chip control be adapted for different materials? Yes, chip control depends on selecting the appropriate chipbreaker and cutting data for the workpiece material and machining stability; the single-sided chipbreaker on this insert assists in predictable chip formation across a range of conditions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 SH7025 Wendeplatten - Tungaloy
Achieve consistent chip control and longer tool life through the combination of a tough coated grade (SH7025) and a stable 80° rhombic geometry; the result is efficient turning performance with predictable edge behaviour. Order the insert directly via Metav Werkzeuge or contact the team for tailored application advice. CCGT 09T302 SH7025 — Indexable turning insert for turning, Tungaloy CCGT 09T302 SH7025 is an ISO-form rhombic indexable insert engineered for general turning applications, offering a robust cutting edge for changing engagement conditions and smaller tooling assemblies. ISO rhombic insert, 80° shape SH7025 coated carbide grade 0.2 mm nose radius for fine finishes Compatible with ISO turning holders Consistent cutting performance under variable conditions The combination of the SH7025 coating and a durable coated carbide substrate delivers a reliable cutting edge that resists chipping during intermittent contact or varying depths of cut. This behaviour supports a reduction in unplanned tool changes and contributes to more predictable cycle times. The grade is designed to perform particularly well in smaller tooling arrangements where thermal and mechanical loads fluctuate; selecting an appropriate chipbreaker and matching the grade to the workpiece material will further extend service life. The construction aims to balance toughness and wear resistance to keep machining stable across common turning challenges. Geometry engineered for precision and surface quality The 80° rhombic shape provides a favourable compromise between strength and accessibility, allowing for robust roughing as well as controlled finishing passes. With a 0.2 mm nose radius, the insert is suited to fine finishing tasks where surface integrity and dimensional conformity matter. The insert presents a 7° relief angle and a plate thickness of 3.97 mm, which together support stiffness when mounted in standard ISO holders. The central hole with a cylindrical bore plus a single-side countersink (40°–60°) ensures secure clamping and repeatable seat seating, reducing variability at re-indexing and improving repeatable concentricity. Simple integration into ISO-based tooling systems Compatibility is determined by insert form, relief angle, tolerance class, fixing type, size and thickness; the ISO conformity of this series eases selection of matching external holders, shims and clamps. A standard system setup comprises the ISO indexable insert, a suitable turn holder or boring bar, and the required shim/klemmsatz and replacement screws. This modular approach reduces setup times and simplifies inventory management, which is particularly advantageous for production environments seeking predictable tool-change workflows and reduced downtime. Applications and practical recommendations Designed primarily for turning operations, the insert excels where cutting conditions vary or where the tooling package is compact. The single-sided chipbreaker concept helps to control swarf when paired with the correct grade and machining parameters. For best results, choose a chipbreaker and cutting data aligned with the workpiece material and machining strategy; when in doubt, match the insert to an ISO holder that corresponds to the 09 size and 80° geometry. The designation CCGT09T302 indicates the ISO form and corner geometry; this designation appears on the item data and should be used to confirm compatibility when ordering replacement inserts. Contact Metav Werkzeuge today for application guidance, availability and matching holder recommendations for the Tungaloy CCGT 09T302 SH7025 indexable turning insert; Metav Werkzeuge can advise on optimal chipbreakers and mounting options Technical data Article number: 6967378 Manufacturer SKU: TUN6967378 SKU: 6967378-Tungaloy Brand: Tungaloy Model series: ISO turning indexable inserts Material: carbide Facts Corner radius: 0.2 mm Shape angle: 80° Relief (clearance) angle: 7° Plate thickness: 3.97 mm Size: 09 Special features ISO rhombic form Coated grade SH7025 Single-sided chipbreaker Central hole: cylindrical bore + single-side countersink (40°–60°) Designed for turning; compatible with ISO holders Suitable for small tools and varying engagement conditions FAQ What machining tasks suit this coated grade best? The SH7025 grade is a tough, wear-resistant coating suited to general turning tasks; the CCGT 09T302 SH7025 insert performs well where engagement can vary or interruptions occur. Which holders are compatible with this insert? Compatibility follows the ISO form and size; the 80° rhombic form and 09 size require holders designed for ISO rhombic inserts and matching thickness and clamping arrangements. What surface finish can be expected with a 0.2 mm nose radius? A 0.2 mm nose radius typically supports fine finishes and tight dimensional control when used with appropriate feeds and speeds; the small radius reduces tool pressure for delicate finishing. Is the insert suitable for internal as well as external turning? Yes, the insert’s geometry and chip control concept permit both external and internal turning applications when installed in the correct holder and with proper cutting data. How is chip control achieved with this insert? Chip control relies on selecting the correct chipbreaker and cutting parameters for the workpiece; the single-sided chipbreaker on this insert supports consistent swarf formation in many turning scenarios. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 SH7025 Wendeplatten - Tungaloy
Take advantage of the combination of a coated carbide SH7025 grade and precise rhombic 80° geometry for consistent turning results; its 0.2 mm nose radius and secure mounting make it a reliable choice for finishing operations — order the insert directly via Metav Werkzeuge or consult the technical team for application advice. CCGT 09T302 SH7025 Turning Insert — ISO indexable turning insert by Tungaloy The CCGT09T302 SH7025 is an ISO indexable turning insert for external and internal turning, featuring a rhombic form with an 80° cutting angle and a 0.2 mm nose radius for fine finish work Coated carbide grade SH7025 Rhombic geometry, 80° cutting angle 0.2 mm nose radius for fine finishing Cylindrical hole with single-sided countersink Increased process reliability through material and grade selection The combination of a coated carbide substrate and the SH7025 grade provides a robust cutting edge that maintains stability under variable engagement conditions. This makes it particularly suited to operations where tool life and consistent surface quality are priorities. The coated structure reduces flank wear and helps control built-up edge formation, resulting in fewer interruptions and predictable reconditioning cycles. When used with an appropriately specified holder, the insert contributes to steady cutting forces and reduced vibration, supporting higher machine utilisation and lower rework rates. Geometry engineered for surface quality and secure clamping A rhombic insert with an 80° principal cutting angle and a 0.2 mm nose radius is optimised for finishing passes where surface integrity and dimensional control are required. The single-sided chipbreaker aids chip control for lighter cuts, while the cylindrical hole with a single-sided countersink (40°–60°) ensures positive, repeatable clamping in compatible toolholders. Tight tolerances in plate thickness and relief geometry contribute to stable contact between insert and seat, which in turn supports consistent part-to-part repeatability and improved surface finish. Practical application notes and holder compatibility Designed for turning operations, including both external and internal machining, the insert requires selection of a matching holder based on form, relief angle, tolerance class, fixation method, size and thickness. The insert is supplied as an ISO-series plate and integrates into standard tool systems when these parameters are matched. For variable cutting conditions or smaller tooling assemblies, the SH7025 grade offers a balance of edge toughness and wear resistance, reducing the need for frequent index changes. For specific material applications and tool holder pairing, technical consultation via Metav Werkzeuge is recommended to ensure optimal tooling configuration. For reliable finishing with Tungaloy's SH7025 grade and secure clamping, contact Metav Werkzeuge for availability and tailored recommendations on the CCGT09T302 insert. Technical data Article number: 6967407 Manufacturer SKU: TUN6967407 SKU: 6967407-Tungaloy Model series: ISO indexable turning inserts Name / designation: CCGT09T302 SH7025 Material: coated carbide Grade: SH7025 Application: turning (external & internal) Core specifications Thickness: 3.97 mm Nose radius: 0.2 mm Relief angle: 7° Cutting angle: 80° Size code: 09 Plate form: rhombic Special features Single-sided chipbreaker Cylindrical hole + one-sided countersink (40°–60°) ISO-compatible Suitable for variable engagement conditions FAQ What materials is this insert suitable for? The insert in SH7025 grade is designed for a broad range of turning tasks; matching the chipbreaker and grade to the workpiece material is advised when using the CCGT09T302 SH7025 Tungaloy insert. How does the hole and countersink affect clamping? The cylindrical hole combined with a one-sided countersink (40°–60°) ensures positive seating and repeatable clamping when used with compatible ISO toolholders. Can the insert be used for both roughing and finishing? The geometry and 0.2 mm nose radius of this insert favour finishing operations; for heavy roughing, selection of a different chipbreaker or a more robust grade may be preferable. What should be considered when replacing an insert? When installing the CCGT09T302 SH7025 insert, verify holder compatibility by form, relief angle and thickness to maintain seat accuracy and cutting stability. Is the insert compatible with standard ISO turning systems? Yes, the insert is part of the ISO-series indexable plates and fits standard ISO holders when sizes and fixation methods correspond. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 SH7025 Wendeplatten - Tungaloy
Benefit from the SH7025 coated carbide grade and the 80° rhombic geometry for stable chip control and consistent tool life; the 0.2 mm nose radius provides accurate dimensional control and improved surface finish. Order genuine inserts via Metav Werkzeuge or consult our specialists for tailored recommendations. CCGT09T302 SH7025 indexable turning insert — ISO turning application, 80° geometry, Tungaloy CCGT09T302 SH7025 is an ISO-compliant rhombic insert designed for general turning applications, offering a balance of edge stability and adaptability for varying engagement conditions ISO rhombic insert with 80° geometry Coated carbide grade SH7025 for edge stability 0.2 mm nose radius for accurate finishes Cylindrical hole with 40°–60° countersink Consistent cutting performance for varied turning tasks The SH7025 coated carbide grade is formulated for edge stability under changing cutting conditions, making it suitable for a wide range of turning operations. The rhombic 80° geometry ensures favourable cutting forces for both roughing and finishing, while the single-sided chipbreaker promotes predictable chip formation. These characteristics reduce vibration and support reliable cycle times, which directly contributes to improved productivity and fewer unplanned tool changes. Precision results from a compact, stable design A 0.2 mm nose radius delivers fine surface quality and tight dimensional repeatability when machining shafts, shoulders or form details. The moderate 7° clearance angle supports secure cutting without excessive flank contact, lowering the risk of premature wear. For smaller tool assemblies or variable engagement depths, the combination of 3.97 mm plate thickness and rhombic form provides a stable cutting edge that helps maintain tolerances and reduces secondary finishing. Easy integration and secure clamping in ISO systems Compatibility with toolholders depends on form, clearance, tolerance class, fixing method, size and thickness. The insert comes with a cylindrical hole and a one-sided countersink (40°–60°), enabling positive and repeatable clamping in standard external holders or boring bars. Using ISO-indexable inserts in a modular holder system simplifies inventory management and replacement; the standardised format also supports fast set-ups and consistent orientation across multiple machines. For demanding turning operations, contact Metav Werkzeuge for application advice and to procure the genuine Tungaloy insert (SKU TUN6967449); email info@metav-werkzeuge.com or call +49 2822 7131930 for personalised support Technical data Article number: 6967449 Manufacturer SKU: TUN6967449 Label: CCGT09T302 SH7025 Tungaloy-Wendeplatte Dimensions & core data Size: 09 Geometry angle: 80° Nose radius: 0.2 mm Plate thickness: 3.97 mm Features & compatibility Material: carbide Coating / grade: SH7025 Clearance angle: 7° Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Chipbreaker: single-sided Application: turning Model series: ISO indexable turning inserts FAQ What materials is this insert suitable for? The CCGT09T302 insert in grade SH7025 is intended for a broad range of turning tasks; its formulation supports stable cutting where edge retention under varying engagement is required. How is the insert secured in the holder? Clamping uses the cylindrical hole with a one-sided countersink (40°–60°) to achieve secure, repeatable fixation in compatible ISO external holders or boring bars. Can this insert be used for finishing operations? Yes — the 0.2 mm nose radius and the rhombic 80° geometry deliver the precision and surface quality expected for finishing, while maintaining robust edge life. Which tolerance and holder criteria determine compatibility? Compatibility is governed by the insert form, clearance angle, tolerance class, fixing method, size and thickness; these parameters must match the chosen holder to ensure correct seating and reliable performance. Is this an original Tungaloy product and how to order? This is an original Tungaloy indexable insert (SKU TUN6967449). For procurement and technical consultation contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 SH725 Wendeplatten - Tungaloy
Benefit from the combination of a 0.2 mm corner radius, SH725 coated carbide and a secure cylindrical-hole clamping design for reliable edge stability and consistent chip control; order the CCGT09T302 SH725 turning insert directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. CCGT09T302 SH725 — ISO turning insert, coated carbide, 0.2 mm radius (Tungaloy) The CCGT09T302 SH725 is a rhombic, ISO-standard turning insert optimised for external and internal turning with a single-sided chipbreaker. Coated carbide grade SH725 Rhombic insert, 80° cutting angle 0.2 mm corner radius Cylindrical hole with single-sided countersink Consistent performance for mixed turning conditions The SH725 grade as a coated carbide combines toughness with edge stability, making it suitable for applications where cutting conditions vary or where smaller tool sizes are used. The result is consistent tool life and reliable chip control under intermittent or unstable engagement. By favouring a robust grade and a dedicated chip control geometry, the insert supports higher process reproducibility and contributes to improved overall productivity on turning centres and lathes. Geometry that balances strength and surface quality A rhombic form with an 80° cutting angle and a 0.2 mm corner radius provides a balance between strength at the cutting edge and the ability to achieve good surface finish. The insert's 7° clearance angle and a plate thickness of 3.97 mm ensure mechanical rigidity and secure seating in the holder, while the single-sided chipbreaker promotes predictable chip formation for typical turning operations. The cylindrical hole with one-sided countersink (40°–60°) allows stable clamping and repeatable positional accuracy, reducing vibration and extending life of the tool system. Clear compatibility and selection guidance for tool systems As an ISO-standard turning insert, compatibility depends on matching the insert form, clearance angle, tolerance class, fixation type, size and thickness with the chosen holder or boring bar. Typical system components include the insert itself, the appropriate external holder or boring bar, a shim or clamp and replacement screws. Selection of the single-sided chipbreaker and the SH725 grade should be guided by workpiece material, desired surface finish and machining stability. For complex assemblies or variable materials, tailored advice helps to choose the optimal chipbreaker and clamping arrangement. For high-reliability turning with Tungaloy SH725 grade, contact Metav Werkzeuge for application-specific recommendations and availability; Metav Werkzeuge’s technical team will advise on the ideal insert, holder and clamping solution. Technical data Article number: 6932699 Manufacturer SKU: TUN6932699 SKU: 6932699-Tungaloy Name: CCGT09T302 SH725 Tungaloy insert Brand: Tungaloy Dimensions & core data Size: 09 Thickness: 3.97 mm Corner radius: 0.2 mm Clearance angle: 7° Cutting angle: 80° Grade: SH725 Features & materials Coated carbide material Rhombic shape Cylindrical hole with one-sided countersink (40°–60°) Single-sided chipbreaker ISO-standard turning insert Suitable for external and internal turning FAQ Which materials is the CCGT09T302 SH725 insert suitable for? The CCGT09T302 SH725 insert is designed as a tough, edge-stable coated carbide grade for a broad range of turning tasks; choose the chipbreaker and machining parameters according to the workpiece material and process stability. What effect does the 0.2 mm corner radius have on machining? A 0.2 mm corner radius increases edge strength and reduces notch sensitivity, improving tool life while still allowing satisfactory surface finish in many turning operations. How is the insert clamped in the holder? Clamping is achieved via the cylindrical hole with one-sided countersink (40°–60°); this geometry enables secure seating with a shim or clamp and replacement screws to ensure repeatable positioning. Which holder characteristics must match the insert? Holder compatibility is determined by insert form, clearance angle, tolerance class, fixation method, size and thickness; matching these parameters ensures correct seating and accurate cutting geometry. What identifiers and SKUs belong to this product? Article number 6932699, manufacturer SKU TUN6932699 and SKU 6932699-Tungaloy identify the CCGT09T302 SH725 turning insert by Tungaloy. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 SH725 Wendeplatten - Tungaloy
A compact indexable solution that combines SH725 coated cemented carbide for edge stability with a 0.2 mm corner radius and an ISO rhombic form for reliable turning performance. Order the inserts directly via Metav Werkzeuge or consult the Metav team for grade and holder matching. CCGT 09T302 SH725 turning insert (rhombic, 80°) — Tungaloy A CCGT09T302 SH725 ISO-compliant rhombic turning insert for external and internal turning, designed for variable engagement and smaller tooling. ISO-compliant rhombic 80° geometry SH725 coated cemented carbide grade 0.2 mm corner radius for versatile finishes Cylindrical hole with 40°–60° countersink Engineered for consistent turning performance The indexable insert presents an ISO geometry that ensures repeatable seating in compatible holders and predictable cutting behaviour. With an 80° rhombic form and a 0.2 mm corner radius, the component provides a balance between strength and finish quality, making it suitable for medium to light turning operations. The 3.97 mm thickness contributes to stability in the clamping zone, reducing vibration and supporting steady chip formation. These attributes result in improved process efficiency and fewer unexpected interruptions in production. Grade selection that suits changing conditions The SH725 grade is a coated cemented carbide designed for toughness and cutting-edge stability, especially where engagement varies or tool sizes are small. The coating enhances wear resistance while the substrate maintains fracture toughness; this combination extends tool life under fluctuating loads. For manufacturers seeking consistent results across mixed batches of workpieces, this grade reduces the frequency of insert changes and supports a higher overall throughput with stable surface quality. Secure mounting and straightforward system integration Compatibility with the selected holder depends on geometry, relief angle, tolerance class, fastening method, size and thickness. The insert features a cylindrical hole with a single-side countersink (40°–60°) to ensure reliable screw clamping and correct seat positioning. As part of a standard ISO insert system, it integrates with corresponding external holders, shims and clamping kits, allowing rapid replacement and minimal set-up time. The single-sided chipbreaker is optimised for common turning tasks and aids predictable swarf control. Contact Metav Werkzeuge for tailored advice on holder compatibility, batch supply and application-specific recommendations; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss Tungaloy SH725 inserts and availability Technical data Article number: 6737005 SKU: 6737005-Tungaloy Manufacturer SKU: TUN6737005 Facts Thickness: 3.97 mm Corner radius: 0.2 mm Included angle: 80° Relief angle: 7° Size designation: 09 Special features Rhombic plate form Coated cemented carbide grade SH725 Single-sided chipbreaker Cylindrical hole with one-sided countersink (40°–60°) ISO-compliant turning insert Intended application: turning FAQ What machining operations is this insert suitable for? This insert is intended for external and internal turning; the SH725 grade and rhombic geometry suit a range of medium to light turning tasks. How does the SH725 grade affect tool life? The SH725 coated cemented carbide combines toughness and wear resistance; the grade enhances cutting-edge stability and typically yields longer life under variable engagement. Which holders are compatible with this insert? Holder compatibility depends on form, relief angle, tolerance class, fastening method, size and thickness; the insert’s ISO geometry and cylindrical hole with countersink support standard clamping systems. Can the insert be used for finishing operations? With a 0.2 mm corner radius and a stable cutting edge, the insert is suitable for achieving good surface finishes in turning where moderate material removal rates are required. What is the manufacturer article number and SKU? The manufacturer article number is 6737005 and the SKU is 6737005-Tungaloy. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 SH725 Wendeplatten - Tungaloy
Take advantage of a tough, coated carbide grade and precise geometry to secure consistent chip control and long service life in general turning operations; order genuine inserts through Metav Werkzeuge or request tailored application advice from our sales engineers. CCGT 09T302 SH725 indexable turning insert by Tungaloy — rhombic profile, coated carbide for turning CCGT09T302 SH725 Tungaloy‑Wendeplatte — an ISO‑format rhombic insert optimised for external and internal turning, offering a 0.2 mm corner radius and a robust SH725 coating grade for variable engagement conditions ISO‑standard rhombic insert CCGT09 size Coated carbide grade SH725 Suitable for external and internal turning Cylindrical hole plus 40°–60° countersink Reliable cutting performance through proven coating and substrate The combination of a coated carbide substrate and the SH725 grade delivers a balance of toughness and edge stability that suits mixed turning tasks and interrupted cuts. The hard coating increases wear resistance while the tough substrate reduces chipping risk, which results in longer effective tool life and fewer insert changes. For production environments where machine uptime matters, this geometry supports steady output and predictable tool‑change intervals. Geometry that controls chips and surface finish A 0.2 mm corner radius and a 7° relief angle provide a controlled contact zone between tool and workpiece, improving surface finish without sacrificing edge strength. The rhombic profile and single‑sided chipbreaker promote reliable chip formation; when combined with appropriate feeds and speeds, the arrangement reduces built‑up edge and improves consistency on a range of steels and non‑ferrous materials. The result is fewer reworks and better first‑pass quality in component turning. Practical compatibility and selection guidance for efficient machining Designed as an ISO‑standard insert, the part fits holders matched by form, clearance angle, tolerance class, fixings, size and thickness; selection of the matching external holder or boring bar and clamping kit is decisive for stability. The insert’s 3.97 mm thickness, 09 size and the cylindrical hole with a 40°–60° countersink ensure secure fastening and repeatable seating. For smaller tool bodies or changing engagement conditions, choose this grade for its predictable edge behaviour and straightforward integration into established tool systems. Contact Metav Werkzeuge for specific machining recommendations or to source genuine Tungaloy inserts and compatible holders for reliable turning results. Technical data Article number: 6737006 Manufacturer SKU: TUN6737006 Dealer SKU: 6737006-Tungaloy Model series: ISO-Drehwendeschneidplatten Material: carbide Grade/coating: SH725 Facts Insert designation: CCGT09T302 Size: 09 Corner radius: 0.2 mm Relief angle: 7° Thickness: 3.97 mm Included angle: 80° Countersink angle: 40°–60° Special features Rhombic plate form Single‑sided chipbreaker Cylindrical hole with one‑sided countersink ISO‑standard compatibility with holders Suited to variable engagement and small tool assemblies Intended application: turning FAQ What materials can this insert machine effectively? The CCGT09T302 SH725 insert is a coated carbide design that performs well on a broad range of materials; the SH725 grade is formulated for toughness and edge stability, making it suitable for many steels and mixed‑condition turning. How does the 0.2 mm corner radius affect cutting results? A 0.2 mm radius balances edge strength and finish: it helps achieve a finer surface without overly concentrating cutting forces, which assists in maintaining tool life for the Tungaloy indexable turning insert. Is the insert compatible with standard ISO holders? Yes — the CCGT09T302 conforms to ISO plate dimensions; compatibility depends on matching form, clearance angle, tolerance class, fastening and thickness with the external holder or boring bar. What does the hole style mean for clamping security? The cylindrical hole with a single‑sided 40°–60° countersink provides reliable seating and repeatable clamping, improving stability and concentricity when used with the correct screw and clamp set. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 SH725 Wendeplatten - Tungaloy
Combining a coated cemented carbide SH725 grade with a precise 0.2 mm corner radius and ISO‑standard form, this insert delivers consistent chip control and long tool life for turning operations. Order the insert directly via Metav Werkzeuge or consult our specialists for application advice. CCGT 09T302 SH725 indexable turning insert by Tungaloy — for precision turning CCGT 09T302 SH725 is an ISO‑standardised rhombic indexable insert designed for external and internal turning where stable cutting edges and reliable chip formation are required ISO‑standardised rhombic insert Coated cemented carbide SH725 One‑sided chipbreaker for controlled chips 0.2 mm corner radius, 7° relief Consistent machining performance with SH725 grade The SH725 coating is a coated cemented carbide grade developed for toughness and edge stability, making it suitable where cutting conditions change or where smaller‑sized inserts are used. The composition provides a balance between wear resistance and fracture toughness, which results in reduced flank wear and fewer unexpected edge failures. In practical terms, this means longer in‑machine life and fewer insert changes, supporting productive turning operations and predictable process windows. Geometry that simplifies setup and improves surface finish The rhombic geometry combined with a 0.2 mm corner radius and a 7° relief angle offers a compromise between robust edge strength and the ability to produce fine surface finishes. The rhombic form is compatible with many standard holders; compatibility is determined by the insert form, clearance angle, tolerance class, fastening method, size and thickness. A small corner radius reduces cutting forces for finishing passes, while the clearance angle prevents rubbing and helps maintain dimensional accuracy. Secure clamping and easy replacement reduce downtime The insert is supplied with a cylindrical hole and a single‑side countersink (40°–60°) to fit common clamping systems and replacement screws. The 3.97 mm thickness and the ISO designation ensure repeatable seating and orientation in the pocket, which aids in achieving consistent cutting geometry after each change. Clear mechanical interface design lowers setup time and reduces the risk of clamping‑related runout, supporting stable turning sequences and higher overall equipment effectiveness. Application range and chip control explained Designed specifically for turning, the insert performs well in both external and internal operations when paired with a matching chipbreaker and insert grade suited to the workpiece material. The product features a one‑sided chipbreaker that promotes controlled chip segmentation, improving evacuation and reducing the chance of workpiece or tool damage. Select the chipbreaker and the SH725 grade according to the substrate and process stability to obtain the best combination of tool life and surface quality. For reliable, productive turning with Tungaloy’s SH725 technology, contact Metav Werkzeuge for immediate availability and application recommendations — Metav Werkzeuge can advise on holder selection and process setup to match the CCGT 09T302 SH725 insert to specific machining needs. Technical data Article number: 6737243 Manufacturer SKU: TUN6737243 Our SKU: 6737243-Tungaloy Model series: ISO turning indexable inserts Designation: CCGT09T302 Full name: CCGT09T302 SH725 Tungaloy indexable insert Facts Size: 09 Thickness: 3.97 mm Corner radius: 0.2 mm Relief/clearance angle: 7° Included angle: 80° Special features Material/coating: coated cemented carbide SH725 Shape: rhombic Chipbreaker: one‑sided Hole style: cylindrical hole + single‑side countersink (40°–60°) Application: turning (external and internal) ISO‑standardised insert CCGT09T302 FAQ Is this insert suitable for both external and internal turning? The CCGT 09T302 SH725 Tungaloy indexable insert is designed for both external and internal turning when used with a compatible holder and the correct chipbreaker for the workpiece material. What materials can be machined with this SH725 grade? The SH725 coated cemented carbide grade is intended for a broad material range and offers toughness for variable cutting conditions; selection should be matched to the substrate and process stability. How does the 0.2 mm corner radius affect machining? A 0.2 mm corner radius provides improved edge strength compared with a sharp corner while still allowing fine surface finishes during finishing and semi‑finishing passes. What clamping features must the holder provide for correct seating? The holder must match the insert form, clearance angle, tolerance class, fastening method, size and thickness; the insert’s cylindrical hole with single‑side countersink (40°–60°) requires corresponding screw and seating provisions. Can the insert be used in automated tool change systems? Yes, the ISO‑standardised dimensions and the repeatable seating offered by the 3.97 mm thickness and ISO designation support use in systems with standard indexable insert change procedures. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CCGT 09T302 SH725 Wendeplatten - Tungaloy
High toughness and a stable cutting edge from the SH725 coated carbide grade combine with ISO‑standard dimensions to deliver consistent turning performance and straightforward toolholder compatibility; order the CCGT09T302 SH725 Tungaloy insert directly via Metav Werkzeuge or ask our consultants for application guidance. CCGT09T302 SH725 Tungaloy turning insert — coated carbide, 0.2 mm corner radius A CCGT09T302 SH725 ISO‑standard rhombic insert for external and internal turning, designed for reliable chip control and repeatable performance in variable engagement conditions. ISO‑standard rhombic insert CCGT09T302 SH725 coated carbide for tough cutting edges 0.2 mm corner radius for precise finishing Cylindrical hole with single‑side countersink Productive turning with a stable cutting edge The SH725 grade is a coated carbide formulation aimed at delivering a tough, edge‑stable performance in turning operations, particularly where tool sizes are small or engagement conditions vary. The single‑sided chipbreaker promotes controlled chip formation which reduces the risk of irregular chips and improves process reliability. With a 0.2 mm corner radius the insert supports fine finishing passes while the rhombic form and robust geometry maintain strength during heavier cuts, resulting in predictable surface quality and longer intervals between index changes. Reduced set‑up time thanks to ISO compatibility This item follows ISO dimensions for turning inserts, so compatibility is determined by form, 7° clearance, tolerance class, fastening method, size and thickness. The standardised format simplifies holder selection and reduces setup errors, helping to shorten machine downtime. The insert's 3.97 mm thickness and the cylindrical hole with a single‑side countersink (40°–60°) ensure secure clamping and repeatable seating in the pocket, which supports process stability across batch runs and tool changes. Versatile grade for a range of turning tasks Designed for both external and internal turning, the insert’s combination of coated carbide and a dedicated chipbreaker makes it suitable for mixed‑material production environments where stable chip formation and consistent tool life are priorities. The insert performs well when matched with a holder appropriate for the 80° cutting geometry and the 09 size, enabling productive machining of components that require a balance of durability and fine edge control. Selecting the correct chipbreaker and grade for the workpiece material and machining stability will maximise cost‑effectiveness and surface finish. Contact Metav Werkzeuge today for tailored application advice and to order the Tungaloy CCGT09T302 SH725 indexable insert — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6737132 Manufacturer SKU: TUN6737132 SKU: 6737132-Tungaloy Model series: ISO turning indexable inserts Material: carbide Grade: SH725 Insert designation: CCGT09T302 Facts Corner radius: 0.2 mm Thickness: 3.97 mm Clearance angle: 7° Cutting angle: 80° Size: 09 Special features Rhombic plate form Cylindrical hole + single‑side countersink (40°–60°) One‑sided chipbreaker Intended application: turning FAQ What materials is this insert suitable for? The CCGT09T302 SH725 Tungaloy insert is a coated carbide grade formulated for broad applicability; choose the appropriate chipbreaker and cutting data according to the workpiece material and stability of the setup. Is the insert compatible with standard ISO toolholders? Yes, the insert follows ISO dimensions and its compatibility depends on holder form, clearance angle, tolerance class, fastening and size — the ISO‑standard format simplifies holder selection. What is the corner radius and what does it influence? The corner radius is 0.2 mm; a smaller radius like this improves finishing capability and reduces cutting forces for fine surface requirements. How is the insert secured in the holder? This insert features a cylindrical hole with a single‑side countersink (40°–60°); that geometry enables positive seating and secure clamping when used with the correct screw and clamping parts. Can the same grade be used for internal and external turning? Yes, the SH725 grade and the rhombic geometry allow use in both external and internal turning; toolpath planning and holder choice should reflect access and engagement conditions. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
CCGT 09T302 SH730 Wendeplatten - Tungaloy
Benefit from the combination of a tough, SH730 coated carbide grade and a compact rhombic geometry that ensures stable cutting edges under variable engagement; this supports consistent cycle times and predictable insert life. Order the insert directly via Metav Werkzeuge or request individual application advice from our consultants. CCGT09T302 SH730 Tungaloy indexable insert for Turning, rhombic 80°, 0.2 mm radius CCGT09T302 SH730 is an ISO-standard indexable turning insert designed for general turning where edge stability and compatibility with ISO toolholders are essential. ISO rhombic insert, 80° cutting face SH730 coated carbide, edge-stable grade Cylindrical hole with 40°–60° countersink Consistent cutting performance with a tough coated grade The combination of a coated carbide substrate and the SH730 grade provides a balance between toughness and wear resistance, developed for turning tasks where engagement can vary. The corner radius 0.2 mm helps to reduce tool pressure peaks while maintaining a reproducible cutting edge, and the rhombic geometry with an 80° cutting face gives favourable chip flow and accessibility for external and internal turning operations. Compatibility is assured by the ISO standard, which simplifies holder selection and reduces setup time. Geometry and chip control that reduce downtime A one-sided chipbreaker and the insert’s hole design — a cylindrical hole with a one-sided countersink (40°–60°) — support secure clamping and controlled chip formation. The relief angle 7° and plate thickness 3.97 mm ensure mechanical stability on small toolholders and during interrupted cuts. Together, these features lower the risk of unexpected edge failure and contribute to more predictable tool-change intervals, making the toolholder system easier to manage in series production. System guidance for rapid selection and safe integration As part of an ISO insert system, selection depends on form, relief angle, tolerance class, fastening method, size and thickness of the insert; matching the SH730 grade and the one-sided chipbreaker to the workpiece material and machining parameters optimises productivity. The insert is suited to setups requiring reliable edge integrity on compact applications and where varying depths of cut can occur. For multi-shift operations, the predictable wear behaviour supports process stability and reduces scrap rates. Contact Metav Werkzeuge for tailored cutting data, availability and application-specific recommendations on the Tungaloy CCGT09T302 SH730 insert — email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance Technical data Article number: 6854007 SKU: 6854007-Tungaloy Manufacturer SKU: TUN6854007 Model series: ISO turning indexable inserts Material: Carbide Facts Corner radius: 0.2 mm Clearance angle (relief): 7° Cutting face angle: 80° Thickness: 3.97 mm Insert size: 09 Special features Rhombic plate geometry Cylindrical hole + one-sided countersink (40°–60°) One-sided chipbreaker Coated carbide, grade SH730 ISO-standardised turning insert Compatibility depends on form, relief, tolerance, fastening, size, thickness FAQ Which turning tasks are best suited to this insert? The CCGT09T302 SH730 insert is designed for external and internal turning where a compact rhombic shape and stable cutting edge are required; it performs well in operations with variable engagement. How does the SH730 grade affect performance? SH730 is a coated carbide grade offering enhanced toughness and edge stability, making the insert suitable for smaller tools and changing engagement conditions without excessive chipping. What does the insert designation mean (CCGT09T302)? The designation identifies a rhombic ISO insert with size 09, specific geometry and a 0.2 mm corner radius; the full code corresponds to the standard ISO form and dimensions for easy holder matching. Are there special clamping or holder requirements? Secure clamping is recommended due to the insert’s compact thickness; the cylindrical hole with a 40°–60° countersink ensures reliable seating in compatible ISO holders and reduces rotation risk Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 TH10 Wendeplatten - Tungaloy
Take advantage of the insert’s combination of ISO compatibility, a sharp TH10 uncoated carbide grade and a low 0.2 mm corner radius to secure consistent surface quality and low cutting forces in turning operations; order directly via Metav Werkzeuge or request application advice from our consultants. CCGT 09T302 TH10 indexable turning insert for ISO turning — Tungaloy CCGT09T302 TH10 is an ISO‑standard indexable insert designed for general external and internal turning applications where low cutting forces and clean surface finish are required ISO rhombic insert size 09 with 80° approach TH10 uncoated carbide for low cutting forces Single‑side chipbreaker for improved surface finish 7° relief angle and cylindrical hole with countersink Consistent clamping and straightforward holder compatibility The insert is manufactured to ISO tolerances so compatibility with a matching holder is assured by geometry, relief angle, tolerance class, fastening and thickness. This standardisation reduces fixture uncertainty and enables reliable indexability across toolposts and boring bars. The rhombic form and the 80° approach angle give predictable tool overhang and contact conditions, which supports steady cutting and repeatable part quality. For shop-floor planning the insert forms part of a system consisting of an ISO insert, a suitable external holder or boring bar, a support shim or clamping set and replacement screws; this system approach simplifies procurement and setup. Low cutting forces and clean finishes with TH10 uncoated carbide The sharp TH10 grade is an uncoated carbide designed as a universal, highly economical option for non‑ferrous materials and operations benefiting from a bare cutting edge. The uncoated edge reduces thermal build‑up at low to moderate cutting speeds, delivering a combination of reduced cutting forces and a cleaner surface finish. The single‑sided chipbreaker is optimised to control swarf and produce a consistent chip form in turning, which eases chip evacuation and reduces finish corrections. Explained plainly: the grade and chipbreaker together help maintain lower spindle loads and a finer surface without resorting to coated grades for every job. Dimensioned for precise results and practical use Key geometrical data such as the 0.2 mm corner radius, 3.97 mm thickness and 7° relief angle define the cutting edge behaviour and allowed cutting parameters. The insert’s cylindrical hole with a single‑side countersink (40°–60°) secures firm clamping and repeatable seating; that stability translates into improved tool life and steady edge performance. The carbide substrate offers the hardness needed for fine finishes while the rhombic form allows multiple indexing positions, supporting economical use of each insert. For determination of process parameters and holder selection, Metav Werkzeuge can provide technical advice and checks against machine capability and workpiece material. Contact Metav Werkzeuge for selection assistance on the CCGT09T302 TH10 insert — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and stock availability Technical Data Article number: 6801324 Manufacturer SKU: TUN6801324 SKU: 6801324-Tungaloy Model series: ISO‑Drehwendeschneidplatten Facts Insert size: 09 Thickness: 3.97 mm Corner radius: 0.2 mm Relief angle: 7° Approach angle: 80° Hole: with hole Hole style: cylindrical hole + single‑side countersink (40°–60°) Special features Material: cemented carbide Grade/coating: TH10 (uncoated carbide) Chipbreaker: single‑sided Shape: rhombic Application: turning System components: insert, holder or boring bar, support shim/clamping set, replacement screws FAQ What materials is the insert suitable for? The CCGT09T302 TH10 insert is specified for non‑ferrous materials and applications where an uncoated carbide edge supports low cutting forces and clean surface finishes. How does the TH10 grade affect cutting performance? TH10 is an uncoated carbide grade that promotes lower cutting forces and reduced thermal loading at the edge, which helps achieve better surface quality in suitable turning operations. Which holders are compatible with this ISO insert? Compatibility is determined by insert form, relief angle, tolerance class, fastening, size and thickness; the ISO‑standard geometry of the CCGT09T302 facilitates use with matching rhombic ISO turning holders and compatible boring bars. What is the function of the single‑sided chipbreaker? The single‑sided chipbreaker on this insert controls chip formation to produce consistent chip shapes and cleaner surfaces, aiding chip evacuation and stabilising the cutting process. How does the 0.2 mm corner radius influence results? A 0.2 mm corner radius reduces cutting edge stress while delivering a fine surface finish and good edge strength for finishing passes in turning applications. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 TH10 Wendeplatten - Tungaloy
Take advantage of the balance of low cutting forces, predictable chip control and ISO-compatible fit to keep turning operations efficient and repeatable — order directly via Metav Werkzeuge or consult our specialists for holder matching and application advice. CCGT 09T302 TH10 Tungaloy indexable turning insert for turning applications The CCGT 09T302 TH10 is an ISO-format, rhombic indexable turning insert designed for external and internal turning where an uncoated cutting edge supports low cutting forces and clean surface finishes. Rhombic ISO insert 09 format Uncoated cemented carbide TH10 grade Single-sided chipbreaker for controlled chips 0.2 mm corner radius for fine finishes Consistent surface quality with reduced cutting forces The combination of an uncoated cemented carbide edge and the TH10 grade produces a sharp cutting geometry that reduces cutting forces and helps maintain tool stability. This characteristic is particularly valuable when machining non‑ferrous materials or light alloys where minimising force prevents workpiece distortion. The modest 0.2 mm corner radius contributes to a smoother finish without compromising edge strength, so cycle times can be optimised while surface integrity is preserved. Predictable chip control and simple clamping benefits Equipped with a single‑sided chipbreaker and a cylindrical hole with a single‑side countersink, the insert provides reliable chip formation that suits interrupted cuts and varying feed rates. Compatibility with standard ISO holders is determined by form, relief angle, tolerance class, clamping and thickness, which simplifies tool changeover and reduces setup time. The 7° relief angle and rhombic profile ensure secure seating in common turning toolholders, promoting repeatability across batches. Robust geometry for productive turning The plain, uncoated cutting edge of this insert supports operations where clean contact and low build‑up are priorities. The rhombic shape and 3.97 mm plate thickness give mechanical stability during higher feed scenarios, while the 80° included angle balances cutting strength with access to features. For shops seeking a practical, economical insert that performs reliably on non‑ferrous components, this solution combines predictable wear behaviour with easy indexation to extend usable life. Application guidance and material suitability This grade is specified for applications that benefit from an uncoated, sharp edge — typically non‑ferrous materials and situations demanding low cut forces and high surface quality. Selection of chipbreaker and grade should match the workpiece material and machining stability; for harder or coated‑demanding tasks, alternative grades or coatings are recommended. The modular nature of ISO inserts allows adaptation to both external and internal turning by selecting the appropriate holder and clamping set. Contact Metav Werkzeuge today for availability and expert guidance on Tungaloy turning solutions — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the CCGT 09T302 TH10 insert and compatible holders Technical data Article number: 6801328 SKU: 6801328-Tungaloy Manufacturer SKU: TUN6801328 Model series: ISO-Drehwendeschneidplatten Brand: Tungaloy Material: cemented carbide Facts Corner radius: 0.2 mm Included angle: 80° Relief angle: 7° Plate thickness: 3.97 mm Insert size: 09 Countersink angle: 40°–60° Special features Rhombic plate form Single‑sided chipbreaker Uncoated grade TH10 Cylindrical hole with single‑side countersink ISO‑standard insert for external and internal turning Compatibility determined by form, relief angle, tolerance, clamping, size and thickness FAQ Is this insert suitable for stainless steel? The TH10 uncoated grade is optimised for non‑ferrous materials and applications requiring low cutting forces; for stainless steel, a dedicated coated grade is generally recommended over the TH10 insert. What size and geometry does the insert have? The insert is an ISO 09 format, rhombic plate with an 80° included angle, 0.2 mm corner radius and 3.97 mm thickness, supplied as the CCGT 09T302 TH10 turning insert. How does chip control perform with this insert? The single‑sided chipbreaker provides controlled chip formation for stable turning operations, particularly effective when machining non‑ferrous alloys and when clean evacuation of chips is required. How is the insert fixed in the holder? The insert features a cylindrical hole with a single‑side countersink (40°–60°) and is compatible with ISO holders that match its form, relief angle, tolerance class, clamping and thickness specifications. Can the CCGT 09T302 TH10 be used for both external and internal turning? Yes, the insert is designed for external and internal turning; appropriate holder selection and stable setup are essential to achieve the stated performance. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of ISO compatibility, low cutting forces and a fine 0.2 mm corner radius for reliable turning performance; order the insert via Metav Werkzeuge or consult the team for application-specific advice. CCGT 09T302 TH10 Turning Insert by Tungaloy — uncoated carbide, 0.2 mm radius The CCGT09T302 TH10 Tungaloy insert is an ISO‑standard rhombic turning insert designed for low cutting forces and improved surface finish in non‑ferrous and similar applications. ISO‑standard rhombic insert Uncoated carbide grade TH10 0.2 mm corner radius for fine detail Single‑sided chipbreaker, with hole Precise cutting with low forces for better surface finish The insert is manufactured from carbide in an uncoated TH10 grade, engineered to keep cutting forces low and to produce clean surfaces when machining non‑ferrous materials and delicate workpieces. The combination of the sharp, uncoated cutting edge and the 0.2 mm corner radius reduces vibration and leaves a finer finish, which is especially beneficial for parts requiring tight tolerances or cosmetic surfaces. This translates into fewer rework cycles and a more predictable machining process, improving throughput and part quality. Reliable ISO compatibility simplifies tooling selection Built to the ISO turning insert form, compatibility with toolholders is determined by insert form, clearance angle, tolerance class, clamping style, size and thickness. The rhombic shape and the with‑hole fixing (cylindrical hole with a single‑side countersink 40°–60°) allow secure mounting in a wide range of standard holders. Clear specification of geometry—including the 7° clearance angle and overall rhomboid form—means straightforward replacement and consistent seating, which reduces setup time and the risk of incorrect clamping. Practical advantages for productive turning operations The single‑sided chipbreaker geometry is tuned to aid chip control while keeping cutting forces low; this supports stable chip evacuation and safer, more efficient turning cycles. Using the TH10 uncoated grade helps to maintain a sharp edge where low cutting resistance is required, making the insert suitable for medium‑feed finishing or light roughing in materials where a coated grade is unnecessary. A well‑matched holder, shim and replacement screws complete the system and ensure repeatable results in batch production. Geometry and handling that support fine features and versatility Key dimensions—size 09, a thickness of 3.97 mm and the compact 0.2 mm corner radius—make the insert suitable for fine profiling and detail work as well as general external and internal turning. The insert’s 80° principal cutting angle and the rhomboid shape provide versatility for a range of tool orientations while maintaining accessibility in constrained setups. Choosing the appropriate chipbreaker and grade for the workpiece material yields the best balance between surface quality and tool life. Contact Metav Werkzeuge for availability of the Tungaloy CCGT09T302 TH10 turning inserts and for tailored application advice — email info@metav-werkzeuge.com or call +49 2822 7131930 for specific recommendations Technical Data Article number: 6801332 Manufacturer SKU: TUN6801332 Item SKU: 6801332-Tungaloy Model series: ISO-Drehwendeschneidplatten Material: Hartmetall Core specifications Size: 09 ISO designation: 09T302 Thickness: 3.97 mm Corner radius: 0.2 mm Clearance angle: 7° Principal angle: 80° Features & compatibility Rhomboid insert form (CCGT) Uncoated carbide, grade TH10 Single-sided chipbreaker With hole: cylindrical hole + one‑side countersink (40°–60°) Application: Turning (external and internal) Compatibility depends on holder form, clearance angle, tolerance, clamping, size and thickness FAQ What materials is this insert suited for? The Tungaloy CCGT09T302 TH10 insert is designed primarily for non‑ferrous materials and applications where an uncoated carbide edge supports low cutting forces and clean surface finishes. How does the TH10 grade affect performance? The TH10 uncoated grade offers a sharp, low‑friction cutting edge that reduces cutting forces and helps achieve finer surface quality when compared with heavier, coated grades in similar applications. What mounting features does the insert have? The insert features a cylindrical hole with a one‑side countersink (40°–60°) for secure clamping and is compatible with ISO‑standard holders that match the form, tolerance class and thickness. Can this insert be used for internal turning? Yes; the rhomboid form and compact 0.2 mm corner radius make the insert suitable for both external and internal turning tasks when combined with a suitable holder and setup. Which parameters should be checked when selecting a holder? Verify holder compatibility for form, clearance angle, tolerance class, clamping method, insert size and thickness to ensure correct seating and secure fixation for the insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 TH10 Wendeplatten - Tungaloy
The combination of a sharp TH10 uncoated carbide grade and the ISO rhombic 80° geometry ensures low cutting forces and consistent surface quality in turning operations; ideal for dependable non-ferrous machining. Order the insert directly via Metav Werkzeuge or consult our specialists for application advice. CCGT 09T302 TH10 ISO turning insert (rhombic, 80°) – Tungaloy The CCGT 09T302 TH10 is an ISO-form indexable turning insert designed for general turning, offering a sharp universal grade for non-ferrous materials and applications where an uncoated cutting edge supports low cutting forces and clean surfaces. ISO 80° rhombic geometry Sharp TH10 uncoated carbide grade Single-sided chipbreaker design Compatible with standard ISO holders Consistent cutting performance for non-ferrous turning The rhombic 80° geometry delivers a reliable cutting angle that balances strength and access for a wide range of turning tasks. Combined with the uncoated carbide composition and the TH10 grade, this insert reduces cutting resistance and promotes steady chip formation when machining non-ferrous metals. The geometry supports stable tool forces, which translates into fewer vibrations and a more consistent surface finish, especially in less rigid setups. The single-sided chipbreaker helps control chip flow without the need for complex cooling strategies. Compatibility and installation that save setup time The insert follows ISO standards, so compatibility with many indexable toolholders is defined by shape, clearance angle, tolerance class, fastening and dimensions. The rhombic shape and the specified thickness of 3.97 mm mean the insert seats securely in typical ISO turning holders and drill bars. The insert’s cylindrical hole with one-sided countersink (40°–60°) enables secure fastening and straightforward replacement, reducing machine downtime and simplifying inventory management for shops that run multiple toolholder platforms. Low cutting forces and improved surface quality Because the cutting edge is uncoated and the grade is optimised as a sharp universal type, the insert generates low cutting forces and clean shearing in suitable materials. This characteristic makes it especially effective for turning operations on brass, aluminium alloys and other non-ferrous alloys where sticking or built-up edge can degrade finishes. The combination of edge geometry and chipbreaker promotes predictable chips and helps maintain a consistent contact zone on the workpiece, improving repeatability from one part to the next. Material specification and practical application guidance Made from solid carbide, the insert is intended for turning applications where an uncoated edge benefits process stability and surface integrity. The single-sided chipbreaker design and the TH10 grade are chosen to match common turning tasks in non-ferrous materials and situations that demand low cutting forces rather than extreme wear resistance. When selecting a holder, ensure matching of form, clearance angle (7°), size and thickness to maintain accuracy; appropriate holder selection secures the repeatable performance expected from ISO indexable systems. Contact Metav Werkzeuge for a tailored application check of the Tungaloy TH10 insert and to confirm stock availability via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: 6801337 SKU: 6801337-Tungaloy Designation: CCGT09T302 Series: ISO turning inserts Material: carbide Facts Corner radius: 0.2 mm Insert size: 09 Thickness: 3.97 mm Clearance angle: 7° Insert angle: 80° Special features Rhombic insert shape Single-sided chipbreaker Uncoated carbide, grade TH10 Cylindrical hole with one-sided countersink (40°–60°) Intended application: turning FAQ What materials is this insert suited for? The CCGT09T302 TH10 Tungaloy indexable turning insert (SKU 6801337-Tungaloy) is optimised for non-ferrous materials such as aluminium and brass, where a sharp, uncoated edge reduces cutting forces and improves surface quality. How does the chipbreaker affect machining? The single-sided chipbreaker on the CCGT09T302 TH10 insert promotes controlled chip formation and evacuation, which supports steady cutting conditions and consistent finishes during turning operations. Which toolholders are compatible with this insert? Compatibility depends on holder form, clearance angle, tolerance class, fastening and size; this ISO-format insert is designed to fit standard ISO turning holders that accept an 09-size rhombic insert with the specified thickness. Is this insert suitable for finishing cuts? Yes, the sharp TH10 uncoated carbide grade supports finishing operations on appropriate materials by reducing cutting forces and helping to produce a clean surface finish. What is the purpose of the insert’s hole and countersink design? The cylindrical hole with a one-sided countersink (40°–60°) ensures secure clamping and accurate repeatable positioning in indexable toolholders, simplifying replacement and reducing setup variation. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 TH10 Wendeplatten - Tungaloy
Take advantage of a sharp, uncoated carbide grade and ISO compatibility to achieve low cutting forces and clean surface finishes in non-ferrous turning; order directly via Metav Werkzeuge or consult our advisors for application-specific guidance. CCGT09T302 TH10 indexable turning insert — Tungaloy The CCGT09T302 TH10 is an ISO-standard rhombic insert designed for external and internal turning, offering a sharp uncoated carbide edge for low cutting forces and improved surface quality ISO-standard rhombic insert for turning Uncoated carbide grade TH10 for clean cuts 0.2 mm corner radius for fine finishing Cylindrical hole with 40°–60° countersink High-efficiency turning of non-ferrous materials The insert is built around the TH10 uncoated carbide grade, optimised for applications where a sharp edge reduces cutting forces and improves the workpiece finish. This grade is particularly effective for aluminium and other non-ferrous alloys, where low friction and minimal built-up edge are decisive. The result is a combination of reduced cutting forces and consistent surface quality, which contributes directly to shorter cycle times and lower tool-change frequency on production runs. Seamless integration into existing ISO tool systems Built to ISO geometry, the indexable insert offers predictable fitment: a rhombic 09 size, 80° included angle and a 7° clearance ensure compatibility with a wide range of holders. Thickness is 3.97 mm and the plate is supplied with a cylindrical hole plus one-sided countersink (40°–60°) for secure clamping. These measurable characteristics make retrofit and replacement straightforward, minimising downtime and simplifying tool inventory management on the shop floor. Precision finishing and chip control in turning operations A 0.2 mm corner radius combined with a single-sided chipbreaker supports fine finishing passes and controlled chip formation. For both external and internal turning tasks, this geometry helps maintain dimensional accuracy and surface integrity when machining less rigid setups or thin-walled components. The insert forms one part of a complete system — the ISO insert, a matching external holder or boring bar, the correct shim/clamp set and spare fastening screws — which together determine final process stability. Practical guidance for selection and use Select the TH10 grade where non-ferrous materials or machining conditions favour an uncoated edge; choose a compatible chipbreaker and insert size according to workpiece material, cutting parameters and machine stability. The insert’s uncoated carbide composition is straightforward to inspect and resharpening or replacement decisions can be based on visible flank wear and edge condition, helping to maintain process reliability without overcomplicating maintenance routines. For application-specific advice or to procure the Tungaloy CCGT09T302 TH10 insert, please contact Metav Werkzeuge — our specialists can recommend the optimal holder and parameters for the intended turning task; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Manufacturer: Tungaloy Manufacturer article number: 6801327 Manufacturer SKU: TUN6801327 Label: CCGT09T302 TH10 Tungaloy-indexable insert Model series: ISO turning indexable inserts Core specifications Corner radius: 0.2 mm Thickness: 3.97 mm Clearance angle: 7° Included angle: 80° Size: 09 Materials & special features Material: carbide (uncoated) Grade: TH10 Chipbreaker: single-sided Hole: with hole; cylindrical + one-sided countersink (40°–60°) Plate shape: rhombic Typical application: turning; external and internal System components: matching holder or boring bar, shim/clamp set, spare screws FAQ What materials is this insert best suited for? The insert is optimised for non-ferrous alloys; the TH10 uncoated carbide grade supports low cutting forces and clean finishes when machining aluminium and similar materials. How does the 0.2 mm corner radius affect machining? A 0.2 mm corner radius provides a balance between edge strength and fine surface quality, making the insert suitable for finishing and semi-finishing passes where dimensional control is required. Is the insert compatible with standard ISO holders? Yes — the insert follows ISO geometry (rhombic 09, 80° included angle, 7° clearance) and is intended for use with appropriate ISO external holders or boring bars and the correct clamping set. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of precise ISO compatibility, sharp TH10 uncoated carbide cutting edges and a compact rhombic geometry for consistent turning results. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific setup. CCGT 09T302 TH10 indexable turning insert — Tungaloy — uncoated carbide, R0.2 CCGT09T302 TH10 Tungaloy indexable insert for general turning, offering an ISO-standard form and a single-sided chipbreaker for clean cuts in non-ferrous materials ISO series CCGT 09T302 indexable insert TH10 uncoated carbide for non-ferrous materials Rhombic 80° form with 0.2 mm nose radius Consistent cutting with low forces and superior surface quality The TH10 grade is an uncoated carbide engineered as a sharp universal grade that reduces cutting forces and promotes a clean surface finish when machining non-ferrous materials and similar applications. This results in lower power demand and reduced vibration during machining, which helps to maintain dimensional stability in production runs. The sharp cutting edge supports delicate chip formation while the single-sided chipbreaker contributes to controllable swarf flow, translating technical properties into measurable productivity gains. ISO-standard geometry that simplifies tooling selection and set-up Designed as part of an ISO series, the rhombic geometry with an included angle of 80° and a 0.2 mm nose radius ensures predictable engagement with compatible holders. Compatibility is defined by the insert form, relief angle, tolerance class, fixing method, size and thickness; this allows straightforward interchangeability in standard external and internal turning toolholders. The insert is supplied with a hole featuring a cylindrical bore and a one-sided countersink (40°–60°), facilitating secure clamping and reproducible seating on the tool body. Application-focused design for productive turning Intended primarily for turning operations, the insert performs well in both external and internal turning when the correct chipbreaker and grade are selected for the workpiece and cutting conditions. The uncoated carbide edge offers advantages where low cutting forces and minimal built-up edge are priorities. The compact plate thickness of 3.97 mm and rhombic shape support stable cutting in interrupted cuts and allow for economical use in high-mix production environments. For machining strategies where tool change speed and repeatability matter, this design contributes directly to shorter cycle times and consistent part quality. Contact Metav Werkzeuge for tailored tooling recommendations or to request technical clarification on fitment and cutting data for the Tungaloy CCGT 09T302 TH10 indexable insert — Metav Werkzeuge will provide application-oriented advice and supply options. Technical data Article number: 6801334 Manufacturer SKU: TUN6801334 Model series: ISO-Drehwendeschneidplatten Application: Turning Material: Carbide Designation: CCGT09T302 TH10 Plate shape: rhombic Plate size: 09 Core data Nose radius: 0.2 mm Thickness: 3.97 mm Included angle: 80° Relief angle: 7° Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Special features Single-sided chipbreaker Uncoated cutting edge (TH10) ISO-standardised indexable insert Suitable for external and internal turning Compact geometry for stable cutting FAQ Which materials is the insert suitable for? The CCGT09T302 TH10 Tungaloy indexable insert is optimised for non-ferrous materials and similar applications where an uncoated, sharp cutting edge supports low cutting forces and a clean surface finish. Can this insert be used for both external and internal turning? Yes, the CCGT09T302 TH10 insert is designed for turning operations and can be applied to both external and internal turning when paired with a compatible ISO holder and appropriate cutting parameters. How is the insert secured in the toolholder? The insert features a cylindrical hole with a one-sided countersink (40°–60°) to enable secure clamping in holders designed for ISO rhombic CCGT shapes; compatibility depends on holder form, fixing method and tolerance. What are the key dimensions to consider? Key dimensions for the CCGT09T302 TH10 insert include a nose radius of 0.2 mm, plate thickness of 3.97 mm and an included angle of 80°, which should match the holder specifications. Is the insert coated or uncoated and what are the implications? The TH10 grade is an uncoated carbide; the lack of coating reduces cutting forces and can improve surface finish in non-ferrous materials, while offering a sharp cutting edge for precise, low-force machining. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T302 UM 1105 Indexable Insert - Sandvik
Are you unsure whether the tool is suitable for your application? Or are you still missing technical data?No problem, just contact us!!! 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Product specifications for CCGT 09T302 indexable inserts from Sandvik Brand: Sandvik Manufacturer Order Number: CCGT09T302UM1105-SANDVIK Dataand Figures: ISO-Code: CCGT09T302 Clearance Angle: 7° Thickness: 3,97mm Radius: 0.2 Special features Material: cemented carbide Grade: 1105 Chip Breaker: UM with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: rhombic Chip Breaker: single-sided Manufacturer: Ownership of brand names and protected trademarks remains with their owners. The use of brand names and trademarks is for descriptive purposes only. There is no connection whatsoever between our company and the brands mentioned. The sales offer includes high-quality, new branded articles from the manufacturer Sandvik. 40START indexable-inserts-CCGT-09T302-1105-Sandvik 40END
CCGT 09T302 UM 1115 Indexable Insert - Sandvik
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271, 📧 eMail: info@metav-werkzeuge.com Information on technical features for CCGT 09T302 indexable inserts from Sandvik Brand: Sandvik Manufacturer Order Number: CCGT09T302UM1115-SANDVIK Figures for the tool: ISO-Code: CCGT09T302 Clearance Angle: 7° Thickness: 3,97mm Radius: 0.2 Features Material: cemented carbide Grade: 1115 Chip Breaker: UM with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: rhombic Chip Breaker: single-sided Manufacturer: Brand names and registered trademarks are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. Our company has no commercial, legal or other connection with the brands concerned. This is a brand new original product of the leading brand Sandvik. 40START indexable-inserts-CCGT-09T302-1115-Sandvik 40END
CCGT 09T302 UM 1125 Indexable Insert - Sandvik
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you 📧 eMail: info@metav-werkzeuge.com, ☎️ Phone: +49 2822 7131930, ✔️ WhatsApp: +49 170 2837271 Detail specifications indexable inserts CCGT 09T302 from Sandvik Brand: Sandvik Manufacturer Order Number: CCGT09T302UM1125-SANDVIK Data/ Figures: ISO-Code: CCGT09T302 Clearance Angle: 7° Thickness: 3,97mm Radius: 0.2 Special features Material: cemented carbide Grade: 1125 Chip Breaker: UM with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: rhombic Chip Breaker: single-sided Manufacturer: Registered trademarks and trade names are the property of their respective owners. The designation of brand names and trademarks is for explanatory purposes only. The brands mentioned are not in any contractual relationship with our company. The items offered are original, brand-new goods of the Sandvik brand. 40START indexable-inserts-CCGT-09T302-1125-Sandvik 40END
CCGT 09T302 UM 1515 Indexable Insert - Sandvik
Unsure whether the tool is the right one? Or are you missing technical data?Just get in touch with us! 📧 eMail: info@metav-werkzeuge.com, ✔️ WhatsApp: +49 170 2837271, ☎️ Phone: +49 2822 7131930 Information on technical features for indexable inserts CCGT 09T302 from Sandvik Brand: Sandvik Manufacturer Order Number: CCGT09T302UM1515-SANDVIK Facts / Figures: ISO-Code: CCGT09T302 Clearance Angle: 7° Thickness: 3,97mm Radius: 0.2 Features Material: cemented carbide Grade: 1515 Chip Breaker: UM with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: rhombic Chip Breaker: single-sided Manufacturer: The rights to brand names and registered trademarks are held by their rightful owners. The indication of brand names and trademarks is for information purposes only. The brands mentioned are not in any contractual relationship with our company. The items offered are original, brand-new goods of the Sandvik brand. 40START indexable-inserts-CCGT-09T302-1515-Sandvik 40END
CCGT 09T302 UM 5015 Indexable Insert - Sandvik
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you 📧 eMail: info@metav-werkzeuge.com ☎️ Phone: +49 2822 7131930 ✔️ WhatsApp: +49 170 2837271 Product specifications CCGT 09T302 indexable inserts from Sandvik Brand: Sandvik Manufacturer Order Number: CCGT09T302UM5015-SANDVIK Figures for the tool: ISO-Code: CCGT09T302 Clearance Angle: 7° Thickness: 3,97mm Radius: 0.2 Features Material: cemented carbide Grade: 5015 Chip Breaker: UM with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: rhombic Chip Breaker: single-sided Manufacturer: Brand names and registered trademarks are the property of their respective owners. The mention of protected brand names and trademarks is for illustrative purposes only. Named brands are in no way associated or co-operate with our company. The sales offer includes high-quality, new branded articles from the manufacturer Sandvik. 40START indexable-inserts-CCGT-09T302-5015-Sandvik 40END
CCGT 09T304 -UM 1205 Indexable Insert - Sandvik
Areyou not sure whether this tool fulfils your requirements? Or do you need additional technical data?No problem - we will be happy to help you ☎️ Phone: +49 2822 7131930 📧 eMail: info@metav-werkzeuge.com ✔️ WhatsApp: +49 170 2837271 Product features for CCGT 09T304 indexable inserts from Sandvik Brand: Sandvik Manufacturer Order Number: CCGT09T304-UM1205-SANDVIK Dataand Figures: ISO-Code: CCGT09T304 Clearance Angle: 7° Thickness: 3,97mm Radius: 0.4 Features Material: cemented carbide Grade: 1205 Chip Breaker: -UM with hole Hole Style: cylindrical hole + single-sided countersink (40°–60°) Form: rhombic Chip Breaker: single-sided Manufacturer: The rights to brand names and registered trademarks are held by their rightful owners. The mention of protected brand names and trademarks is for illustrative purposes only. Named brands are in no way associated or co-operate with our company. The sales offer includes high-quality, new branded articles from the manufacturer Sandvik. 40START indexable-inserts-CCGT-09T304-1205-Sandvik 40END
CCGT 09T304 AH725 Wendeplatten - Tungaloy
Take advantage of the combination of reliable process security, a universal PVD-coated grade and precise geometry to ensure consistent turning results across mixed steel batches; order the insert directly via Metav Werkzeuge or consult the technical team for application-specific advice. CCGT09T304 AH725 – ISO turning insert CCGT for turning, PVD-coated carbide, 0.4 mm radius by Tungaloy The CCGT09T304 AH725 is an ISO-standard rhombic turning insert designed for external and internal turning applications, offering universal, breakage-resistant performance for steel and stainless steels. ISO rhombic turning insert CCGT09T304 PVD-coated AH725 carbide grade 0.4 mm corner radius for consistent profiles Cylindrical hole with one-sided countersink Designed for external and internal turning Stable process security for mixed steel production The combination of a PVD-coated surface and the AH725 grade provides a balance between toughness and wear resistance that supports stable machining across varying steels, including stainless variants. The coating reduces adhesive wear and supports higher cutting temperatures, which results in fewer unexpected tool changes and a more predictable production rhythm. As a consequence, cycle times become more reliable and scrap rates are decreased, particularly where batch materials vary or component geometries demand consistent tool life. Geometry engineered for repeatable part quality A 0.4 mm corner radius and an 80° lead angle on the rhombic profile maintain form accuracy and enable controlled chip formation at the cutting edge. The one-sided chipbreaker is matched to the grade to assist chip control during both external and internal turning, reducing the risk of built-up edge on stainless steels and tough alloys. The geometry supports a repeatable surface finish and dimensional stability, so finishing passes are minimised while tolerances remain tight. Simple mechanical integration and robust clamping Compatibility with toolholders is determined by form, clearance angle, tolerance class, fastening, size and thickness; the insert’s with-hole design and the specified cylindrical hole with one-sided countersink (40°–60°) ensure secure seating and straightforward fixation in common ISO CCGT holders. The 3.97 mm plate thickness and size 09 fit many standard external holders and boring bars, facilitating fast changeover and reliable torque transfer. This predictable fit helps maintain consistent cutting conditions across shifts and operators. Reduced process risk through material choice and coating Manufactured from fine-grain carbide and finished with a PVD layer, the insert combines fracture resistance with edge stability, making it suitable for smaller tools and operations where process safety is critical. In short, the grade selection and coating strategy reduce the incidence of edge chipping and improve overall tool life when machining medium to high-strength steels and stainless steels, particularly under variable machining conditions. Application-focused guidance for planners and operators For external and internal turning tasks where material groups change or where high process reliability is required, this insert offers a pragmatic compromise between economy and performance. Selection of feed, depth of cut and holder rigidity should reflect the intended material and machining strategy; the insert’s universal character simplifies tooling inventories while preserving performance. Compatibility checks against holder geometry and clamping method are recommended prior to series use. For dependable, versatile turning performance from Tungaloy’s AH725 grade, contact Metav Werkzeuge for ordering and application guidance — Metav Werkzeuge can provide compatibility checks and tailored recommendations. Technical Data Article number: 6857019 Manufacturer SKU: TUN6857019 SKU: 6857019-Tungaloy Model series: ISO-Drehwendeschneidplatten Application: Turning Material: Carbide Grade: AH725 Dimensions & Geometry Corner radius: 0.4 mm Insert size: 09 Thickness: 3.97 mm Insert shape: Rhombic Lead angle: 80° Clearance angle: 7° Hole: with hole Hole style: cylindrical hole + one-sided countersink (40°–60°) Coating, Compatibility & Use Coating: PVD Compatible for: Steel and stainless steels Typical use: External and internal turning Chipbreaker: one-sided Cutting material: PVD-coated carbide FAQ What materials is the CCGT09T304 AH725 best suited for? The CCGT09T304 AH725 insert is engineered for machining steel and stainless steels, offering a universal, breakage-resistant performance suited to mixed-material production. How does the PVD coating affect tool life? The PVD-coated AH725 grade boosts wear resistance and reduces adhesive wear at elevated temperatures, which extends tool life under standard turning conditions. Which holders are compatible with this insert? Compatibility is determined by the insert form, clearance angle, tolerance class, fastening, size and thickness; the CCGT09T304 is designed to seat in standard ISO CCGT holders with corresponding clamping systems. What chip control can be expected with the one-sided chipbreaker? The one-sided chipbreaker, matched to the AH725 grade, supports controlled chip formation for both external and internal turning, improving evacuation and reducing re-cutting. Are there any special considerations for stainless steels? When machining stainless steels, the PVD coating and robust carbide substrate of this insert help minimise built-up edge; however, cutting parameters should be adapted to material toughness and thermal conductivity. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
CCGT 09T304 AT9530 Wendeplatten - Tungaloy
Take advantage of the AT9530 cermet grade and ISO geometry for improved surface finish and consistent wear; the precise 0.4 mm corner radius and single-sided chipbreaker ensure reliable chip control during finishing and light machining of steel. Order directly via Metav Werkzeuge or consult our specialists for application matching. CCGT 09T304 AT9530 — Turning insert (ISO CCGT09T304) by Tungaloy, cermet finishing grade, 0.4 mm radius, 7° relief A CCGT09T304 AT9530 indexable insert for turning, optimised for finishing and light machining of steel with ISO-compatible geometry and secure clamping. Cermet grade AT9530 for superior finish ISO CCGT09T304 geometry, rhombic 80° shape 0.4 mm corner radius for fine turning Single-sided chipbreaker for stable chips Cylindrical hole with 40°–60° countersink Outstanding surface quality and predictable tool life The insert combines a coated cermet substrate with the AT9530 grade to prioritise surface finish and even wear over extended cycles. Cermet materials reduce built-up edge and deliver a fine, consistent surface in finishing passes; this means fewer downstream operations and less rework. The 0.4 mm corner radius is selected to balance a fine cutting edge with strength, producing accurate profile control without sacrificing life span. Predictable flank wear reduces process variation and supports stable batch production. Consistent chip control and machining stability A single-sided chipbreaker paired with the rhombic, 80° geometry promotes controlled chip formation during external and internal turning, reducing the risk of snarled chips and machine interruptions. The insert’s 7° relief improves shear conditions on light cuts, lowering cutting forces and vibration. These features translate into fewer stops for cleaning or manual intervention and a smoother cycle time in high-mix or repetitive operations, enhancing overall shop-floor efficiency. ISO compatibility and secure clamping for safe operation Designed as an ISO-standard turning insert, the plate is defined by form, relief angle, tolerance class, fastening method, size and thickness to ensure compatibility with suitable toolholders and boring bars. The cylindrical hole with single-sided countersink (40°–60°) enables reliable centring and positive clamping, while the 3.97 mm thickness provides a stable support surface under clamping loads. This combination reduces micro-movement at the cutting edge and supports repeatable set-ups across multiple holders and machines. Practical application advice and material suitability Engineered specifically for finishing and light machining of steel, the AT9530 coating emphasises balanced wear and consistent performance across common steel grades. In practice, select cutting data that favour finishing feeds and moderate depths of cut to exploit the grade’s strengths: improved surface integrity and lower tendency for built-up edge. The insert is ideal where surface quality and repeatability are valued over heavy stock removal, helping to shorten inspection and finishing times while maintaining throughput. Contact Metav Werkzeuge for tailored machining recommendations on the Tungaloy AT9530 cermet insert and arrange technical matching via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6967289 SKU: 6967289-Tungaloy Manufacturer SKU: TUN6967289 Manufacturer: Tungaloy Numbers / Core technical data ISO designation: 09T304 Insert designation: CCGT09T304 Corner radius: 0.4 mm Relief angle: 7° Insert thickness: 3.97 mm Shape/approach angle: rhombic / 80° Designs / Special features Coating / grade: AT9530 Substrate: cemented carbide (coated cermet) Chipbreaker: one-sided Hole: with cylindrical hole + single-sided countersink (40°–60°) Typical application: turning — finishing and light machining of steel System composition: ISO insert, suitable external holder or boring bar, support/clamping set and replacement screws FAQ What materials is this insert suitable for? The insert is specified for finishing and light machining of steel; the AT9530 coated cermet offers improved surface finish and uniform wear when turning steel grades. Which insert geometry does the product use? This is an ISO-format rhombic insert in the CCGT series (CCGT09T304) with an 80° approach angle and a 0.4 mm corner radius for fine turning tasks. How does the chipbreaker affect machining? The single-sided chipbreaker on the Tungaloy insert promotes controlled chip formation and reliable evacuation, reducing interruptions and improving process stability. Will the insert fit my holder? Compatibility depends on insert form, relief angle, tolerance class, fastening method, size and thickness; the ISO CCGT geometry ensures broad compatibility with standard holders designed for CCGT inserts. What clamping features ensure secure mounting? The insert is supplied with a cylindrical hole and a single-sided countersink (40°–60°) to provide positive centring and stable clamping under normal turning loads. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Why indexable inserts are indispensable in modern machining
Indexable inserts, also known as cutting inserts or indexable cutting inserts, are standardised, replaceable cutting elements that mount on tool holders such as turning bits, milling cutters or drills. Made from wear-resistant materials like carbide, cermet, ceramic or other superhard grades, they carry the actual cutting edge and allow a worn corner to be rotated or flipped instead of replacing or regrinding the entire tool body.
How these inserts work and when to choose them
In everyday workshop and production settings, indexable inserts perform the direct material removal on the workpiece. Standard inserts for tool systems without internal coolant typically feature closed faces or a single central fixing hole, with heat evacuation handled by external machine nozzles. Inserts designed for systems with internal coolant are engineered to support coolant flow: they include calculated chipbreaker geometries that guide an internal coolant jet under the chip or, in specialised designs, contain sintered microchannels to direct coolant right to the cutting edge. Such coolant-compatible inserts are essential for machining heat-resistant alloys, heavy cutting operations and deep internal machining, where thermal load and chip control are critical.
Tangible benefits for production and workshop efficiency
Choosing the right indexable inserts delivers measurable operational advantages:
- Reduced downtime: faster changeover because a worn insert is simply indexed rather than the whole tool being replaced.
- Extended cutting-edge life: targeted coolant application and optimised chipbreaker design lower thermal stress and improve tool life.
- Consistent part quality: predictable cutting-edge geometry from standardised inserts maintains tolerances across batches.
- Versatility: availability in carbide, cermet, ceramic and superhard grades permits selection according to workpiece material and cutting conditions.
- Lower tooling costs over time: fewer full-tool replacements and less regrinding required.
Metav as a dependable source for inserts and tooling systems
Metav combines decades of precision expertise with a wide-ranging supply chain, positioning itself as a practical partner for industry, craft and trade. From Emmerich on the Rhine, Metav operates as a quality filter for the European market, offering more than 250,000 products and serving over 48,000 customers. For procurement teams aiming to reduce supplier count while retaining technical reliability, Metav’s assortment of indexable inserts and compatible tool holders provides a central, trustworthy solution.
Quick summary
Indexable inserts (cutting inserts or indexable cutting inserts) enable economical, repeatable material removal by allowing worn cutting edges to be indexed or replaced quickly; coolant-adapted designs further reduce thermal load and enhance chip control for demanding applications.
FAQ
What materials are indexable inserts available in?
Indexable inserts are available in wear-resistant grades such as carbide, cermet, ceramic and other superhard materials, selected according to the workpiece material and cutting conditions.
When should I choose inserts with internal coolant support?
Choose inserts designed for internal coolant when machining heat-resistant alloys, performing heavy cuts or working in deep internal features, because the coolant reduces thermal load at the cutting edge and actively improves chip breakage.
How do chipbreaker geometries affect performance?
Chipbreaker geometries on indexable inserts guide the chip flow and, when matched to an internal coolant jet, direct the coolant under the chip to control temperature and facilitate reliable chip formation, which extends edge life and stabilises machining.
Can standard inserts be used with external coolant only?
Yes; standard inserts for tool systems without internal coolant typically have closed faces or a central fixing hole and rely on external machine nozzles for heat evacuation, which is sufficient for many routine, accessible cuts.
Why source inserts through Metav?
Metav supplies a broad range of indexable inserts and tooling, backed by decades of expertise and a comprehensive European stock, making it a practical choice for consistent quality and dependable delivery.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com