40mm S32T SVUCR Boring Bar SVUC for VCMT Indexable Inserts 50mm Cutting Height, 300mm Overall Length - Teknik Makina

Take advantage of a rigid, right-hand SVUC toolholder with a Shaft Ø 32 mm and compatibility with VCMT 1604 indexable inserts for efficient, repeatable internal machining — order directly via Metav Werkzeuge or consult our specialists for tailored support.

Boring bar SVUC for VCMT indexable inserts — Teknik Makina, rigid toolholder with 32 mm shaft and 300 mm length

Boring bar SVUC for VCMT indexable inserts offers a compact, purpose-built solution for internal turning and boring where stiffness and reliable insert seating are essential

• Right-hand cutting orientation
• Shaft Ø 32 mm for enhanced rigidity
• Compatible with VCMT 1604 inserts
• Overall length 300 mm for deep reach

Increased stability for better surface finishes

The S32T SVUCR configuration provides a stout, well-balanced holder that reduces chatter and improves concentricity during internal operations. With a Shaft Ø 32 mm and Overall length 300 mm, the assembly keeps deflection to a minimum so the toolholder transfers cutting forces efficiently into the machine. The listed weight 1.833 kg contributes to a predictable dynamic behaviour, which results in more consistent component tolerances and prolonged insert life. For workshops seeking measurable improvements in cycle-time reliability, the combination of shaft diameter and mass offers a clear advantage in rigidity over slimmer alternatives.

Fast, economical machining with standard indexable inserts

Engineered for use with VCMT 1604 indexable inserts, the toolholder accepts common insert sizes for quick changes and predictable cutting geometry. The cutting angle 93° and cutting edge height 50 mm ensure correct seating and alignment of the insert, reducing setup time and the risk of incorrect clamping. Using indexable inserts keeps consumable costs transparent and enables targeted selection of grades for specific operations. In practical terms, the design supports efficient material removal rates and repeatable surface quality while keeping tooling overhead low.

Practical range and safe clamping for workshop use

Designed for right-hand operations, the toolholder’s Right-hand cutting orientation and nominal diameter 40 mm shank offer compatibility with a wide range of toolposts and holders. The specified clamping interface (designation 16) facilitates secure fixation and simple set-up when pairing with standard clamping systems. The robust geometry simplifies alignment checks and reduces the need for frequent reworking. For production environments that value uptime, the holder’s straightforward configuration supports rapid insert replacement and predictable maintenance cycles, contributing to smooth shop-floor throughput.

Speak to Metav Werkzeuge for specification advice on Teknik Makina boring bars and secure reliable supply from Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com

Technical data

• Article number: K214TM
• ISO designation: S32T SVUCR
• Type: SVUC for VCMT indexable inserts
• Brand: Teknik Makina

Facts

• Shaft diameter: 32 mm
• Shank/outer diameter: 40 mm
• Overall length: 300 mm
• Cutting edge height: 50 mm
• Cutting angle: 93°
• Weight: 1.833 kg
• Cutting direction: right
• Clamping designation: 16

Special features

• For VCMT 1604 indexable inserts
• S32T SVUCR configuration
• Right-hand orientation
• Robust, stiff construction
• Quick insert replacement

FAQ

Which inserts fit this boring bar?
The boring bar is specified for VCMT 1604 indexable inserts; the geometry and seating are matched to that insert form for secure clamping and correct cutting height.

Is the holder suitable for deep internal boring?
With an Overall length 300 mm and Shaft Ø 32 mm, the holder is intended for deeper reach where increased rigidity is required compared with slimmer bars.

What is the orientation of the cutting edge?
The toolholder is configured for right-hand cutting, which should be selected according to the lathe or turning machine’s setup and the intended machining direction.

How does the tool ensure insert alignment?
The cutting edge height 50 mm and cutting angle 93° provide a defined seating plane and repeatable alignment for VCMT inserts, minimising set-up variation.

What identifiers should be quoted when enquiring?
Quote the SKU K214TM, the ISO designation S32T SVUCR, and the brand Teknik Makina to ensure precise correspondence.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com