20mm A16Q SDUCR Boring Bar For DC-- 0702 Indexable Inserts, Internal Coolant, 93° Cutting Angle, 150mm - Teknik Makina

Take advantage of the combination of robust rigidity, internal coolant and proven compatibility with DC-- 0702 indexable inserts for consistent machining performance; order directly via Metav Werkzeuge or consult our specialists for application advice.

A16Q SDUCR Boring Bar – 16 mm Shank, Internal Coolant (Teknik Makina)

The A16Q SDUCR is a compact boring bar for use with DC-- 0702 indexable inserts, engineered for right-hand turning operations where stability and coolant-fed cutting are required

• ISO A16Q SDUCR, 16 mm shank
• Designed for DC-- 0702 inserts
• Internal coolant for chip control
• Right-hand cutting, 93° cutting angle

Greater rigidity for repeatable bore quality

The compact 16 mm shank combined with a 20 mm body diameter gives a favourable stiffness-to-length ratio that reduces vibration and improves bore roundness. A shorter overhang and a well-dimensioned cutting height (30 mm) lower the risk of chatter during finishing cuts, so the toolholder delivers consistent surface finish and dimensional stability over serial runs. For shops aiming to increase first-pass yield, this structural balance directly reduces rework and inspection time.

Internal coolant that improves tool life and chip flow

Built-in internal coolant channels direct cutting fluid straight to the cutting zone to support effective chip evacuation and temperature control. By flushing chips away from the insert pocket, the coolant reduces edge wear and the chance of chip re-cutting, which translates into longer insert life and fewer unexpected tool changes. In practice, this improves process reliability and helps maintain cutting parameters for longer production cycles.

Fast indexable insert changes and reliable cutting geometry

The boring bar is configured as SDUC for DC-- indexable inserts, accepting DC-- 0702 plates for quick insert replacement and standardised clamping. The 93° cutting angle and right-hand cutting direction support neutral to slightly negative tool engagement, easing entry into the workpiece and allowing stable material removal on typical turning centres. The indexable system minimises downtime: worn corners are exchanged rapidly without manual regrinding, keeping throughput high.

Compact length and low weight for versatile mounting

With a total length of 150 mm and a weight of just 0.25 kg, the bar suits compact toolposts and tight set-ups where space is limited. The modest mass reduces centrifugal loads in higher-speed turning and simplifies balancing during multi-tool configurations. For workshops that change fixtures frequently or run small-batch production, the low weight and compact footprint make handling and set-up quicker, improving overall machine utilisation.

For reliable, coolant-fed boring operations with Teknik Makina quality, contact Metav Werkzeuge to discuss the A16Q SDUCR boring bar (SKU KA126TM) and application-specific recommendations – call +49 2822 7131930 or email info@metav-werkzeuge.com

Technical data

• Article number: KA126TM
• ISO designation: A16Q SDUCR
• Manufacturer: Teknik Makina

Dimensions & weight

• Shank diameter: 16 mm
• Cutting height: 30 mm
• Body diameter: 20 mm
• Overall length: 150 mm
• Weight: 0.25 kg
• Cutting angle: 93°

Features & compatibility

• For indexable inserts DC-- 0702
• Internal coolant: yes
• Cutting direction: right
• SDUC configuration for DC-- indexable inserts

FAQ

What insert type does this boring bar accept?
The A16Q SDUCR is prepared for DC-- 0702 indexable inserts, using the SDUC plate form for simple, fast replacement.

Is internal coolant integrated in the bar?
Yes, the boring bar includes internal coolant channels to supply cutting fluid directly to the cutting edge and improve chip evacuation.

What are the main dimensions to check when mounting?
Key mounting values are the 16 mm shank diameter, 150 mm overall length and the 20 mm body diameter, which determine clamping suitability and overhang.

Which cutting direction is supported?
The tool is configured for right-hand cutting, matched to conventional turning and boring setups requiring right-hand engagement.

How does the 93° cutting angle affect machining?
A 93° cutting angle provides a near-neutral geometry that helps controlled entry into the workpiece and stable chip formation for a wide range of turning tasks.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com