KGMN 300-02 Indexable Insert for Stainless Steel - MetavCUT

Benefit from the combination of a 32 mm blade height and a narrow 2.45 mm cutting edge for accurate, efficient parting; order the KL35TM through Metav Werkzeuge or ask our specialists for tailored application advice. Teknik Makina KL35TM parting blade — 32 mm height, 150 mm length Teknik Makina KL35TM parting blade designed for grooving and parting operations in precision turning applications, compatible with KGMN 300 indexable inserts. 32 mm blade height for deep grooving 2.45 mm narrow blade for precise parting Fits Korloy KGMN 300 indexable inserts 150 mm overall length for stable clamping Precision for demanding grooving operations The Teknik Makina KL35TM parting blade offers a reliable geometry tailored to consistent cut control. With a 32 mm blade height and a 25 mm cutting height, the tool provides a stable reference for axial positioning, which reduces chatter and improves surface finish. The narrow 2.45 mm blade width minimises material waste during parting and enables fine, accurate separations on small-diameter workpieces. These dimensional specifications are intended to support repeatable setups and shorter cycle times in production environments where precision is essential. Seamless compatibility with indexable inserts and holders Compatibility with established insert systems is a practical advantage. The blade is specified for use with KGMN 300 indexable inserts from Korloy, allowing well-known insert geometries and grades to be chosen according to material and cutting conditions. The design also matches clamping holders with a max. cutting depth 36 mm, which permits secure installation and full exploitation of the blade’s height. Using standardised inserts simplifies tool management, reduces retooling time and makes it straightforward to select coatings or grades for specific metals without changing the blade geometry. Robust geometry that supports efficient machining A 150 mm overall length provides sufficient reach and lever arm for stable clamping while keeping the unsupported length moderate to limit deflection. The blade’s proportions promote efficient chip flow and reduce the risk of jamming during deep cuts. Built for workshop resilience, the geometry is compatible with common turning setups and can be integrated into existing toolholding systems. The result is a balance between rigidity and accessibility: operators benefit from reliable parting actions and reduced tool-change frequency, which contributes to smoother production schedules. Practical advantages for procurement and workshop planning Selecting standardised components streamlines inventory and maintenance. The blade’s fit with Korloy’s KGMN 300 inserts means tooling can be standardised across multiple machines, lowering stock variety and simplifying reordering. Technical teams will value the clearly defined dimensions — 32 mm blade height, 25 mm cutting height, 2.45 mm blade width, 150 mm length — which support accurate fixture design and repeatable setups. This clarity reduces downtime caused by mis-matched components and supports predictable manufacturing throughput. For a reliable supply from our Emmerich hub and expert application guidance on the KL35TM, contact Metav Werkzeuge to discuss which Korloy insert grades best suit the intended materials and cycle times Technical Data Article number: KL35TM Manufacturer: Teknik Makina Facts Blade height: 32 mm Cutting height: 25 mm Blade width: 2.45 mm Overall length: 150 mm Max. stechtiefe (holder): 36 mm Special features Compatible with Korloy KGMN 300 indexable inserts Designed for grooving and parting operations Suited to standard clamping holders FAQ What inserts are compatible with this parting blade? The KL35TM parting blade is compatible with Korloy KGMN 300 indexable inserts and accepts standard insert geometries for grooving and parting. What are the key dimensions to check before installation? Check the 32 mm blade height, 25 mm cutting height, 2.45 mm blade width and the 150 mm overall length to ensure correct alignment in the holder. Which maximum cutting depth is supported by the holder interface? The blade is designed to work with clamping holders that permit a max. cutting depth of 36 mm. Is the blade suitable for use with standard turning toolholders? Yes, the KL35TM is intended for integration with standard clamping holders compatible with KGMN 300 inserts and typical grooving setups. How does the narrow blade width benefit production? A 2.45 mm blade width reduces material loss during parting and allows finer separations, which is advantageous for precision components and material-saving processes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of accurate parting with a 21.4 mm cutting height and a slim 2.45 mm blade width for reduced material waste and reliable chip control; order the parting blade directly via Metav Werkzeuge or contact the consultants for application support. Parting blade KL38TM — precision parting blade with 21.4 mm cutting height (Teknik Makina) A precision parting blade for lathe and turning operations, the Parting blade KL38TM is designed for narrow kerf cutting and stable clamping in medium-duty workshop and CNC environments. Precision parting with 21.4 mm cutting height Narrow 2.45 mm blade for minimal kerf Robust 26 mm blade shank height Compatible with KGMN 300 Korloy inserts Consistent, low-kerf parting for efficient material use The KL38TM parting blade delivers precise separation thanks to its 21.4 mm cutting height and slender 2.45 mm blade width. A reduced kerf means less material loss per cut and lower cutting forces, which translates into quieter operation and fewer secondary finishing steps. Compatibility with KGMN 300 inserts from Korloy ensures a predictable cutting geometry; the insert type defines the edge radius and chip control, so insertion and replacement are straightforward for standardised parting tasks. Stable support for predictable tool life and surface quality A 26 mm shank height and overall length of 110 mm provide a rigid mounting that reduces chatter and vibration during parting. This stiffness supports consistent surface finish on the parted face and extends insert life by limiting uncontrolled tool deflection. The specified maximum cutting depth of 36 mm indicates the practical reach for deeper parting operations without compromising clamping security, making the blade suitable for many routine turning and slotting procedures where stability is essential. Seamless workshop integration and adaptable use The KL38TM integrates into existing toolholders that accept KGMN 300-style inserts, simplifying changeover and keeping machine idle time low. As a standardised parting solution from Teknik Makina, the blade is suited to both manual lathe shops and CNC turning centres that demand repeatable results. The compact profile supports tight workpiece layouts and makes the blade a cost-effective option for operations requiring frequent parting with minimal setup complexity. For tailored advice on integrating the Teknik Makina KL38TM parting blade into specific turning operations, contact Metav Werkzeuge for consultancy and reliable supply from Emmerich. Technical data Article number: KL38TM Designation: Parting blade Manufacturer: Teknik Makina Core dimensions Blade height: 26 mm Cutting height: 21.4 mm Blade width: 2.45 mm Length: 110 mm Max cutting depth: 36 mm Compatibility & features Compatible insert: KGMN 300 Suitable inserts manufacturer: Korloy Intended use: parting / slotting Manufacturer SKU: KL38TM FAQ What insert type fits this parting blade? The KL38TM parting blade is designed for use with KGMN 300 inserts and is compatible with Korloy KGMN 300 insert geometries. What is the maximum cutting depth for the blade? The maximum practical cutting depth for the KL38TM parting blade is 36 mm, as specified for deeper parting operations. Which machines and applications suit this blade? This parting blade from Teknik Makina is suitable for manual lathes and CNC turning centres where standard KGMN 300 inserts are used for parting and narrow-slot cutting. How does the blade profile affect material waste? The 2.45 mm blade width produces a narrow kerf, reducing material loss per cut and lowering downstream machining and finishing effort. Is the KL38TM suitable for heavy interrupted cuts? The KL38TM offers a robust 26 mm shank height for improved stability, but suitability for heavily interrupted cuts depends on specific machine rigidity and clamping; evaluate setup conditions when planning aggressive cutting. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com