110mm Stech Sword Grooving Tool 26mm Height 3.45mm Blade Width, For Sandvik N151-4 - Teknik Makina

Take advantage of a precise, rigid parting solution with clear insert compatibility and compact dimensions for consistent cycle times. The slim 3.45 mm blade width and 21.4 mm cutting height ensure stable separations while the 110 mm overall length simplifies integration into standard toolholders — order directly via Metav Werkzeuge or consult our specialists for verification.

Parting Blades KL54TM — parting blade for indexable inserts, 3.45 mm width, 110 mm length (Teknik Makina)

The Parting Blades KL54TM are a compact parting solution intended for fine parting and grooving tasks where compatibility with Sandvik indexable inserts (N151-4) and consistent cut control are required.

• Compatible with Sandvik N151-4 inserts
• Blade width 3.45 mm for narrow cuts
• Cutting height 21.4 mm for insert fit
• Length 110 mm for robust mounting

Precise geometry for consistent parting results

The KL54TM series is engineered to deliver precision and repeatability in parting and grooving operations. The narrow 3.45 mm blade profile minimises material waste while maintaining adequate rigidity to reduce chatter. With an overall length of 110 mm and a cutting height of 21.4 mm, the design matches the seat dimensions of standard indexable inserts such as Sandvik N151-4, enabling secure clamping and consistent cutting height. This controlled geometry translates directly into shorter cycle times and fewer rejects in serial turning environments.

Designed to improve process efficiency and tool life

A focus on stable clamping and correct insert seating reduces stress on the cutting edge and the holder, which helps to extend tool life and lowers overall tooling costs. The blade’s dimensions allow accurate alignment in common grooving and parting holders, supporting predictable chip flow and less thermal loading at the cutting zone. For production-focused workshops and smaller job shops alike, the result is a measurable improvement in process reliability and a reduction in unexpected downtime.

Practical application notes for workshop integration

These parting blades suit a variety of turning setups where indexable inserts are preferred for fast insert changes and repeatable results. The KL54TM is specified for use with Sandvik N151-4 inserts, ensuring a proper geometric match for height and seat form; this compatibility simplifies inventory and reduces setup complexity. Suitable mounting in a rigid parting holder and correct insert torque are recommended to exploit the blade’s stiffness and to avoid premature wear. The combination of narrow blade and correct insert pairing is especially effective when minimal material removal and precision separation are priorities.

What the dimensions mean for selection and planning

When planning tooling for a turning cycle, the blade width (3.45 mm) indicates the kerf size and minimum remaining material, while the cutting height (21.4 mm) confirms seat compatibility with the referred insert series. The overall 110 mm length provides enough engagement for many standard holders without excess overhang, which helps to maintain stability. These technical parameters enable straightforward comparison with existing holders and inserts, supporting informed purchasing decisions and faster setup on the machine.

For assured parting accuracy and confirmed compatibility, discuss the KL54TM parting blade with Metav Werkzeuge — our specialists at Metav Werkzeuge can verify fitment with Sandvik N151-4 inserts and advise on the best holder arrangement; call +49 2822 7131930 or email info@metav-werkzeuge.com

Technical data

• Article number: KL54TM
• Manufacturer: Teknik Makina
• Designation: Parting blades (Stechschwerter)
• eClass: 21181018

Numbers / Core technical data

• Length: 110 mm
• Blade width: 3.45 mm
• Blade height: 26 mm
• Cutting height: 21.4 mm

Compatibility and special features

• Compatible insert: N151-4
• Compatible insert manufacturer: Sandvik
• Application: Parting / grooving with indexable inserts

FAQ

What inserts are recommended for these blades? The parting blades KL54TM are specified for use with Sandvik N151-4 indexable inserts to ensure correct seating and cutting height.

What are the key dimensions to check for holder compatibility? Check the 110 mm overall length, 3.45 mm blade width and 21.4 mm cutting height when matching holders and inserts for secure mounting of the KL54TM.

Is the KL54TM suitable for narrow kerf parting operations? Yes, the slim 3.45 mm blade width is intended for narrow kerf operations where minimal material removal and high precision are required.

Can these blades be used with other insert brands? Compatibility is defined for Sandvik N151-4 inserts; alternative brands may be usable if they match the same insert geometry and seat dimensions as specified for KL54TM.

How does the cutting height affect setup? The 21.4 mm cutting height determines the required insert seat position in the holder and must match the holder’s insert pocket to ensure stable cutting and correct tool centreline alignment.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com