LDMT14T308R-F57 WSP45G WSP45G Wendeplatten - Walter Tools

Take advantage of the combination of Tiger·tec Gold coating, versatile P/M/S material capability and a precise corner radius of 0.8 mm for consistent milling performance; order the insert directly via Metav Werkzeuge or request tailored advice from our consultants.

LDMT14T308R-F57 WSP45G – milling indexable insert by Walter Tools (Tiger·tec Gold, PVD-coated)

LDMT14T308R-F57 WSP45G is a rectangular milling insert designed for general milling applications where a balance of edge stability and chip control is required

• Tiger·tec Gold PVD-coated grade WSP45G
• Suitable for Stahl and rostfreier Stahl machining
• Rectangular insert with corner radius 0.8 mm
• Optimised chipformer F57 for stable chip control

High efficiency and broad material range for milling operations

The Tiger·tec Gold technology used in this grade provides a PVD-coated carbide surface that promotes stable chip formation and extended edge life under typical milling loads. The insert is formulated for machining across the P/M/S groups, meaning suitability for Stahl, rostfreier Stahl and high-temperature superalloys or titanium, with the substrate and coating balancing toughness and wear resistance. As a result, the insert reduces unplanned stoppages through predictable wear behaviour and consistent cutting forces, which supports steady productivity on components that demand repeatable results.

Geometry engineered for reliable surface quality and repeatability

The rectangular shape combined with a corner radius of 0.8 mm and a relief of 15° yields a geometry that supports stable cutting edges and good surface finishes in a range of feeds and depths. The tolerance class M ensures dimensional consistency between inserts, which is important for serial production and repeat setup routines. The thickness designation T3 and size 14 contribute to the mechanical stiffness of the pack, reducing vibration during interrupted cuts; the outcome is improved dimensional control and fewer rework cycles on parts requiring close tolerances.

Practical benefits on the shop floor: chip control and cost-efficiency

The integrated F57 chipformer is optimised to break and evacuate chips reliably during milling, lowering the risk of built-up edge and thermal concentration at the cutting edge. This leads to longer effective tool life and fewer insert changes per shift, supporting a lower total cost of ownership for milling operations. The grade’s balance of toughness and wear resistance facilitates a wide processing window, making the insert a practical choice for mixed production runs. For application-specific cutting data or optimisation across machining centres, Metav Werkzeuge’s technical advisers are available to assist with recommended feeds, speeds and fixture considerations.

For application-specific recommendations on the Walter Tools LDMT14T308R-F57 WSP45G, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for tailored cutting data and procurement support

Technical Data

• Article number: LDMT14T308R-F57-WSP45G-WALTER
• Type: Milling indexable insert
• Designation: LDMT14T308R-F57 WSP45G
• Manufacturer: Walter Tools

Numbers

• Corner radius: 0.8 mm
• Relief angle: 15°
• Size: 14
• Thickness: T3
• Tolerance class: M

Special features

• Series: Tiger·tec Gold
• Grade: WSP45G (PVD-coated carbide)
• Applicable materials: Stahl; rostfreier Stahl; high-temp superalloys and titanium
• Form: Rectangular
• Chipformer: F57

FAQ

Is this insert suitable for machining stainless steels?
Yes. The LDMT14T308R-F57 WSP45G grade is formulated for rostfreier Stahl and provides stable chip formation and edge resistance under the higher temperatures typical of these alloys.

Which chip control does this insert offer?
The insert uses an F57 chipformer, designed to produce short, controllable chips during milling, reducing the likelihood of re-cutting and built-up edge.

What are the key geometry values for this insert?
The insert features a corner radius of 0.8 mm and a relief angle of 15°, with a tolerance class of M for consistent interchangeability.

Can this grade handle titanium and superalloys?
Yes. WSP45G is specified for the S material group, enabling milling of high-temperature superalloys and titanium where heat resistance and edge strength are required.

How does the Tiger·tec Gold technology help in production?
The Tiger·tec Gold coating improves wear resistance and thermal stability of the cutting edge, extending the insert’s effective life and supporting predictable performance over longer cycles.

Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany

Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, brand-new goods from the manufacturer Walter Tools.