100mm Brake Disc Gauge 120mm Jaw, Matt Chrome, Vernier 0.1mm, Inox, Supplied in Case - Metav IndustryLine

Take advantage of a robust workshop instrument that combines stainless steel construction, a compact 0–100 mm measuring range and a clear Vernier 0.1 mm reading for dependable brake disc checks; order or consult via Metav Werkzeuge for tailored advice and supply.

Brake disc inspection gauge M201.181 – stainless steel, Vernier 0.1 mm (Metav IndustryLine)

The Brake disc inspection gauge M201.181 is an analogue measuring caliper developed for rapid dimensional checks of brake discs and similar components in workshop and inspection environments.

• Stainless steel construction, matt chrome finish
• Measuring range 0–100 mm, compact format
• Vernier scale 0.1 mm resolution
• Jaw length 120 mm for deep contact

Consistent workshop readings for routine inspection

The analogue Vernier scale provides a reliable, mechanically robust alternative to digital instruments, giving a readable graduation of 0.1 mm that suits frequent checks during maintenance shifts. Solid stainless steel construction with a matt chrome surface reduces wear and resists workshop grime, so calibration stays stable between service intervals. The compact 0–100 mm range places this instrument in the standard workshop class, offering the best balance of reach and stiffness for everyday brake disc thickness and diameter checks while remaining easy to handle and store.

Purpose-built geometry for brake disc control

With a jaw length of 120 mm, the gauge is dimensioned to engage brake discs at appropriate contact points, simplifying thickness verification without elaborate fixturing. The instrument’s analogue nature removes dependence on batteries and electronics, allowing direct comparison readings and immediate pass/fail decisions during inspection runs. Where a simple, repeatable measurement routine is needed, this caliper supports efficient throughput and reduces process interruptions, contributing to measurable time savings on each service bay.

Durable design that supports workshop practice

The matt chrome plating on the stainless base material improves scratch resistance and gives a non-reflective surface that helps visibility of the Vernier marks under workshop lighting. Being an analogue instrument, maintenance consists mainly of cleaning and occasional lubrication of the slide, keeping lifetime costs low while maintaining measurement reliability. The tool is ideal for technicians who prioritise robust, low-maintenance instruments that integrate seamlessly into standard quality-control workflows.

Contact Metav Werkzeuge for application guidance or to arrange a supply of the M201.181 brake disc inspection gauge from Metav IndustryLine; regional stock and technical consultants in Emmerich can advise on compatibility with inspection procedures and dispatch options.

Technical data

• Article number: M201.181
• GTIN: 4054469100951
• ECLASS: 21170344
• Customs tariff number: 90173000
• Manufacturer: Metav IndustryLine

Facts

• Measuring range: 0–100 mm
• Jaw length: 120 mm
• Reading / graduation: 0.1 mm (Vernier)
• Instrument type: analogue vernier caliper

Special features

• Material: inox (stainless steel)
• Finish: matt chrome plated
• Application: brake disc inspection and basic workshop metrology
• Format: compact standard caliper suitable for hand operation

FAQ

How accurate is the Vernier on this gauge?
The Vernier provides a reading graduation of 0.1 mm; typical workshop reproducibility aligns with the instrument’s analogue design and stable stainless construction.

Can the instrument measure brake disc thickness reliably?
Yes, the caliper’s jaw geometry and 120 mm jaw length are intended to support rapid brake disc thickness checks and dimensional verifications in service environments.

Is the gauge suitable for everyday workshop use?
The matt chrome finish and stainless steel base make the instrument robust against routine handling and contamination, supporting continuous use with minimal maintenance.

Does the instrument require batteries or electronic upkeep?
No; being an analogue vernier caliper, the gauge operates mechanically and does not require batteries.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com