300mm Precision Caliper With Pointed Jaws, Fine Adjustment, Hardened Stainless Steel, 0.02mm Vernier, Supplied In Case - Metav IndustryLine

Combining a hardened stainless steel body with a fine-adjustment mechanism and a 0.02 mm vernier scale delivers repeatable workshop measurements for daily production tasks; order the caliper directly via Metav Werkzeuge or consult the Metav specialists for procurement and application advice.

Workshop Caliper M201.303 – stainless, hardened, 300 mm with fine adjustment

Workshop Caliper M201.303 is a robust analogue caliper designed for accurate outside, inside and step measurements across general metalworking and assembly tasks.

• Hardened stainless steel construction
• Precision scale with 0.02 mm resolution
• Fine-adjustment thumb screw
• Monoblock frame with 100 mm jaws

Built to last for everyday workshop use

The slide and frame are made from stainless steel, hardened for wear resistance and fitted with a matt-chromed scale to reduce glare and preserve legibility under harsh workshop lighting. The monoblock design increases rigidity and reduces torsion during use, which helps maintain measurement accuracy over time. At approximately 0.7 kg, the instrument balances solidity with manageable handling, and the extended 100 mm jaws allow secure gripping of workpieces without sacrificing control.

Precise reading and controlled contact force

Equipped with a vernier scale that offers 0.02 mm resolution, the caliper ensures measurements that meet typical workshop tolerances. The dual vernier layout provides finely gradu­ated readings—metric graduations supported by a clear secondary scale—while the dedicated fine-adjustment thumb screw permits delicate sliding for exact closure and alignment. These features reduce reading errors and enable reliable measurements for component checks, setup tasks and quality control where consistent, reproducible results are required.

Designed for standard workshop ranges and practical use

With a measuring range of 0–300 mm, the instrument falls into the Standard category, offering the best compromise between reach and stiffness for everyday machine‑shop and metal‑fabrication work. The caliper is intended for routine dimensional checks on shafts, housings and machined parts, and its construction supports use in fabrication, maintenance and small-series production environments. The tool is delivered to factory standard; the supplied configuration reflects workshop expectations for durability and simple, low‑maintenance operation.

Choose the Metav IndustryLine caliper for robust, accurate measurements and contact Metav Werkzeuge for tailored advice and reliable supply direct from Emmerich.

Technical Data

• SKU: M201.303
• GTIN: 4054469101262
• Weight: 0.7 kg
• Material: stainless steel, hardened with matt‑chromed scale
• Label: Workshop Caliper 300 x 100 x 0.02 mm

Dimensions & Performance

• Measuring range: 0–300 mm
• Jaw length: 100 mm
• Resolution: 0.02 mm
• Vernier: top 1/1000 inch, bottom 1/50 mm
• Tariff number: 90173000

Special features

• For external, internal and step measurement
• Monoblock frame for increased rigidity
• Fine-adjustment thumb screw
• Factory standard (Werksnorm)
• Analogue vernier instrument

FAQ

What measuring range does this caliper cover?
The Workshop Caliper M201.303 covers a measuring range of 0–300 mm and is classified in the Standard category for general machine‑shop use.

Which materials is the caliper suitable for inspecting?
The stainless steel, hardened construction of this vernier caliper makes the instrument suitable for routine inspection of steel, aluminium and similar workshop materials.

How fine are the vernier graduations and what accuracy is expected?
The vernier provides a 0.02 mm resolution; with correct technique this enables repeatable workshop measurements that meet common machining tolerances.

Does the instrument include a fine adjustment for precise sliding?
Yes, the caliper features a fine‑adjustment thumb screw to permit controlled sliding and exact alignment when taking measurements.

Is this caliper suitable for internal and step measurements as well as outside checks?
Yes, the design supports external, internal and step measurements, making it versatile for component inspection and setup tasks.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com