300mm Workshop Caliper Without Probe Fine Adjustment 0.05mm Stainless Steel 90mm Jaws, Monoblock, DIN 862 - Metav IndustryLine

Combine hardened stainless‑steel construction, a 300 mm measuring range and micrometric fine adjustment for dependable workshop measurements; benefit from robust stiffness and clear graduations for routine quality control. Order the caliper directly via Metav Werkzeuge or consult the technical advisors for application guidance.

M201.321 Workshop Caliper – 300 mm, Stainless, Fine Adjustment

The M201.321 Workshop Caliper is an analogue 300 mm caliper designed for everyday engineering use, combining hardened stainless construction with a matt‑chromed scale and micrometric fine adjustment for repeatable readings.

• Hardened stainless steel construction
• 300 mm standard range for workshop use
• Micrometric fine adjustment for repeatable results
• Vernier: 1/128" upper, 1/20 mm lower

Reliable measurements where they matter

The caliper’s hardened stainless steel frame and monoblock design deliver high torsional stiffness, which reduces flexing during clamping and improves repeatability across many measurements. Compliance with DIN 862 for typical jaw lengths ensures that results can be referenced against common workshop standards; this translates into fewer rechecks, faster throughput and a measurable reduction in scrap from mis‑measured parts. The matt‑chromed scale reduces glare, making readings quicker under workshop lighting.

Practical precision for daily quality control

An analogue vernier scale with a readable graduation of 0.05 mm gives the instrument the industrial‑standard accuracy expected in machine shops. The dual vernier arrangement (1/128" upper, 1/20 mm lower) supports both metric and inch interpretation, while the integrated fine adjustment spindle lets operators make slow, controlled closure of the jaws for repeatable contact pressure. These features together simplify setting‑up and make the tool efficient for batch inspections and setup checks.

Built for workshop endurance and usability

Classified in the standard range (maximum measuring span 100–300 mm), this caliper strikes a balance between reach and handling: long enough for common components yet stiff enough for one‑handed operation. The matt‑chrome finish and hardened surfaces resist wear from regular use in industrial environments, reducing maintenance intervals and preserving scale legibility. The vernier mechanism and fine feed are straightforward to use, supporting quick handovers between operators without an extended learning curve.

For practical advice on integrating the M201.321 into a shop workflow or to request application recommendations from Metav Werkzeuge, contact our specialists who will advise on measurement routines and compatibility with existing inspection processes.

Technical Data

• Article number: M201.321
• GTIN: 4054469101422
• ECLASS: 21170344
• Material: hardened stainless steel with matt‑chromed scale
• Type: analogue vernier caliper
• Monoblock construction
• Fine adjustment included

Facts

• Measuring range: 0–300 mm
• Jaw length: 90 mm
• Graduation / resolution: 0.05 mm
• Vernier: 1/128" (upper) and 1/20 mm (lower)
• Norms: DIN 862 (jaw length up to 200 mm), factory standard above 250 mm

Special features

• Hardened measuring surfaces
• Matt‑chromed scale for reduced glare
• Robust monoblock frame for stiffness
• Micrometric fine adjustment for precise contact
• Designed for standard workshop measurement tasks

FAQ

Is this caliper suitable for everyday workshop tasks?
The M201.321 workshop caliper is designed for routine machine‑shop and metalworking measurements within the standard 0–300 mm range, offering robust construction and a readable vernier for reliable daily use.

What resolution and reading accuracy can be expected?
With a graduation of 0.05 mm and a vernier arrangement of 1/128" (upper) and 1/20 mm (lower), the instrument provides the industrial‑standard mechanical resolution commonly used for workshop quality control.

Does the caliper meet recognised standards?
The M201.321 is specified to conform to DIN 862 for typical jaw lengths, ensuring compatibility with common metrology practice in production environments.

How does the fine adjustment help in measurement tasks?
The integrated fine adjustment allows slow, controlled movement of the jaw, reducing operator‑induced variation and improving repeatability when setting measurement contacts.

Which materials and environments is this caliper intended for?
Constructed from hardened stainless steel with a matt‑chromed scale, the caliper is built to withstand typical workshop conditions and regular handling while keeping the scale legible.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com