300mm Workshop Caliper With Pointed Jaws Fine Adjustment Monoblock 0.05mm Vernier, Hardened Stainless Steel, Cased - Metav IndustryLine

Take advantage of a hardened stainless-steel construction, precise 0.05 mm vernier resolution and a fine‑adjustment screw for repeatable workshop measurements; the monoblock design increases stiffness for everyday use. Order the M201.331 workshop caliper directly via Metav Werkzeuge or ask our consultants if needed.

M201.331 Workshop caliper — 300 mm, hardened stainless steel (Metav IndustryLine)

A M201.331 workshop caliper engineered for standard metalwork and maintenance tasks, offering a 300 mm measuring range, fine adjustment and pointed jaws.

• 300 mm measuring range for workshop standards
• Hardened stainless-steel construction
• Fine-adjustment screw for exact positioning
• Supplied in protective case for transport

Robust construction for dependable daily use

Built as a standard-class measuring instrument for the workshop, this caliper combines a monoblock body with hardened stainless steel to resist wear and maintain alignment over time. The 300 mm range places the tool in the Standard category (measuring range up to 100–300 mm), which is widely used in machine shops because it balances reach with rigidity. The matt‑chromed scale reduces glare and aids clear reading on the analogue scale, while the robust single‑piece construction lowers the risk of play between beam and slider, so measurements remain reproducible across repeated cycles.

Precise vernier reading and practical accuracy

The analogue vernier layout provides a readable two‑scale arrangement (top vernier 1/128" and lower vernier 1/20 mm), delivering a practical resolution of 0.05 mm for routine quality control and workshop checks. This level of mechanical precision is suitable for general engineering tasks where DIN‑level repeatability is required; the jaw geometry and vernier spacing are designed to yield quick, verifiable readings without relying on electronics. For jaw lengths up to 200 mm this instrument adheres to DIN 862 conventions, ensuring compatibility with common inspection routines.

Versatile jaws and controlled measurement force

Equipped with pointed jaws, the caliper is suited to measuring narrow grooves, small bores and stepped features that standard flat jaws struggle to access. The integrated fine‑adjustment screw allows controlled slider movement for precise closing and setting, reducing overshoot and the influence of operator force. Together, these features make the instrument a practical choice for workshop technicians who need fast, accurate checks on components such as fixtures, shafts and assembly interfaces.

Designed for handling, storage and longevity

Practical details support daily use: the matt finish on the scale preserves legibility, the hardened alloy resists knocks and abrasion, and the instrument is supplied in a protective case to simplify transport and reduce the risk of damage in transit. Careful handling and occasional cleaning with a soft cloth and light oil will preserve the sliding fit and prolong service life. The overall design emphasises a low-maintenance workflow so the caliper can be integrated into routine inspection, setup and assembly procedures with minimal downtime.

For robust, workshop‑grade measuring choose the Metav IndustryLine M201.331 workshop caliper and contact Metav Werkzeuge in Emmerich for ordering or application advice: info@metav-werkzeuge.com / +49 2822 7131930

Technical data

• Article number: M201.331
• GTIN: 4054469101651
• Brand: Metav IndustryLine
• Category: Messschieber
• eClass: 21170344

Facts

• Measuring range: 0–300 mm
• Resolution (analogue): 0.05 mm
• Vernier: 1/128" (top) and 1/20 mm (bottom)
• Jaw length: 90 mm

Special features

• Monoblock design
• Hardened stainless-steel body
• Matt‑chromed scale
• Fine‑adjustment screw
• Pointed jaws for narrow features
• Supplied in protective case for transport
• Conforms to DIN 862 for jaw lengths up to 200 mm

FAQ

What measurement accuracy can be expected from this caliper? The M201.331 workshop caliper provides an analogue resolution of 0.05 mm using its vernier arrangement; this is suitable for standard workshop and machine‑shop inspections where millimetre/sub‑millimetre precision is required.

Can the caliper measure internal and external dimensions as well as steps? Yes; the instrument is designed for external, internal and step measurements thanks to its jaw geometry and pointed tips, making it versatile for common workshop tasks.

Is the instrument suitable for regular workshop use on metal components? Yes; the hardened stainless‑steel construction and monoblock design make the caliper robust for routine metalwork checks, fixture setup and maintenance tasks.

Does the product come with a case for transport and storage? The caliper is supplied in a protective case to facilitate safe transport and to reduce the risk of damage between uses.

Does the caliper meet recognised standards? The M201.331 follows DIN 862 conventions for applicable jaw lengths (the instrument’s 90 mm jaw length falls within the DIN scope), aligning it with common inspection practices.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com