300mm Dial Caliper 0.01mm Resolution Four-Point Measurement Plastic Case DIN 862 - Metav IndustryLine

Take advantage of the combination of precise 0.01 mm reading, a clear 45 mm dial and four measurement modes for consistent workshop quality control; ordering is possible directly via Metav Werkzeuge or by consulting the technical advisors for specification alignment.

Dial Caliper "TOP" M202.136 — 300 mm range, 0.01 mm dial reading (analog)

The Dial Caliper "TOP" is an analogue measuring instrument designed for workshop and precision‑engineering use, offering clear mechanical readout and robust features for general machine and metalworking inspection.

• Analog dial, 0.01 mm resolution
• 45 mm easy‑read dial
• Four measuring functions (in/out/depth/step)
• Locking screw, thread pitch table on reverse

Precision and compliance for everyday workshop control

The dial instrument delivers a 0.01 mm reading resolution combined with mechanical robustness that suits routine quality checks and setup tasks. Compliance with DIN 862 ensures the measuring chain follows recognised workshop standards, which simplifies traceability and documentation in production environments. The 45 mm dial provides an enlarged, easy‑to‑read display that reduces interpretation errors during repeated inspections; the analogue principle avoids battery dependency while offering immediate, tactile feedback. Together these characteristics make the tool appropriate for assembly benches, maintenance departments and light quality‑control stations where reproducible results matter.

Designed for reliable handling and repeatable results

With a measuring range classed as Standard (100–300 mm), the instrument balances reach and stiffness to measure common components such as shafts, housings and mounting fixtures with stable guidance. The inclusion of a locking screw secures the slider for transfer measurements or template marking, while a thread pitch table on the reverse speeds up fast checks on threaded parts without the need for separate references. Mechanical construction and slide guidance prioritise repeatability, so each measurement cycle returns comparable values — a key factor when the measuring routine is repeatedly performed on production lines or in quality audits.

Practical features that speed up inspection tasks

The caliper supports four measuring functions — external, internal, depth and step — enabling multiple routine tasks with one instrument and reducing tool changes during inspection sequences. The clear analogue dial readout helps technicians maintain focus on the component rather than on menus or electronics, increasing throughput in simple inspection workflows. Lightweight and compact handling characteristics favour single‑hand operation at the bench; combined with the instrument’s straightforward design, this reduces training time for new operators and simplifies incorporation into existing measuring sets for workshops and service departments.

Contact Metav Werkzeuge for advice on specifying the Dial Caliper "TOP" (M202.136) and arrange delivery from our Emmerich quality centre

Technical data

• Article number: M202.136
• GTIN: 4054469102344
• Brand: Metav IndustryLine
• Norm: DIN 862

Core technical data

• Measuring range: 0–300 mm
• Resolution: 0.01 mm
• Dial diameter: 45 mm
• Measuring functions: 4 (external/internal/depth/step)

Special features

• Analog dial readout
• Locking screw for secure measurements
• Thread pitch table on reverse face
• Classification: Standard (100–300 mm)
• Mechanical construction, no battery required

FAQ

Is the Dial Caliper "TOP" suitable for workshop quality control? The Dial Caliper "TOP" (M202.136) is intended for workshop and light quality‑control tasks thanks to its 0–300 mm range and 0.01 mm readout.

Which measurement types can be performed with this caliper? The instrument supports external, internal, depth and step measurements, enabling four distinct inspection tasks without tool changes.

Does the caliper comply with recognised standards? Yes, the device is manufactured to meet DIN 862, which defines general requirements for calipers used in industrial environments.

Is an electronic data interface available for the instrument? This is an analogue dial instrument; no electronic data output is provided for the Dial Caliper "TOP".

What practical aids are included for thread checking? A thread pitch table is printed on the reverse face to facilitate quick identification and basic verification of thread pitches during inspection.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com