100-250mm Gauge Pins Set, 4‑Piece For Internal Fine Gauging - Metav IndustryLine

Take advantage of a compact accessory that matches workshop standards: the set combines reliable compatibility with the 208.027 gauge, a dedicated 100–250 mm measuring span and the practical convenience of a four‑piece configuration. Order the set directly via Metav Werkzeuge or consult the team for specification matching and delivery.

4‑piece measuring pins for 208.027 (100–250 mm) — M8/7.2 mounting (Metav IndustryLine)

The 4‑piece measuring pins for 208.027 (100–250 mm) form a compact accessory set designed to extend internal gauging capability across the standard workshop measuring range, offering secure M8/7.2 mounting for repeatable positioning.

• Set of four precision measuring pins
• Matched to 100–250 mm measuring range
• M8/7.2 mounting interface
• Low mass reduces probe load

Precise alignment for internal measurement tasks

The set of four measuring pins is designed to support accurate internal gauging across the 100–250 mm span, providing a simple way to adapt existing fixtures without extensive rework. The pins locate into the holder using an M8/7.2 interface, ensuring a consistent seating that reduces lateral play and improves measurement precision. With a nominal mass of 0.02 kg, the pins exert minimal additional load on the measuring head, so measurements remain stable and repeatable during routine checks. This compact accessory suits busy inspection benches where quick, reliable fitting is required and where small changes in probe load can otherwise introduce error.

Compatibility and downtime reduction for production environments

Designed as an accessory for the 208.027 family, the set supports rapid replacement and modular upgrades, helping to keep inspection plans on schedule. The set of four allows immediate swap‑outs when wear is detected, reducing machine downtime and avoiding lengthy recalibration cycles. Because the components are tailored to the instrument’s mounting standard, mechanical compatibility is assured and no ad‑hoc adapters are needed. That compatibility translates directly into operational efficiency: fewer interruptions, straightforward spare‑parts handling and a predictable stock item for routine maintenance.

Measurable workflow benefits for workshop metrology

Fitted within the Standard range for workshop gauges, this accessory improves throughput by simplifying setup for internal measurements. Repeatability is enhanced through consistent seating and matched geometry, which lowers variability from one probing cycle to the next. The low‑mass construction decreases dynamic influence on fine measuring systems, contributing to better short‑term stability and therefore clearer pass/fail decisions in quality control. Where inspection speed and traceable repeatability matter, the pins offer a pragmatic way to raise measurement confidence without large capital outlay.

Practical handling, identification and traceability

Each pack is supplied as a compact, four‑piece set with clear identification for inventory and procurement. The item is listed under SKU M208.027.BZ and carries GTIN 4054469146683 to support ERP and traceability workflows. The simple M8/7.2 mounting means fitment is straightforward for workshop technicians, and the small overall footprint makes the set easy to store as a labelled spare. For users aligning inspection equipment to standard gauges, this accessory is a logical, low‑risk addition that keeps measurement chains consistent and auditable.

For tailored advice on integrating the Metav IndustryLine measuring pins set into existing gauges, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss compatibility, lead times and delivery options.

Technical data

• Article number: M208.027.BZ
• GTIN: 4054469146683
• ECLASS: 21170310
• TARIC / customs code: 90179000
• Category: Zubehör (accessory)

Numbers

• Measurement range: 100–250 mm
• Weight: 0.02 kg
• Pieces per set: 4
• Aufnahme / mounting: M8/7.2

Special features

• Accessory for model 208.027
• Intended for internal measurement tasks
• Compact four‑piece configuration
• Suited to standard workshop measuring range (100–300 mm)

FAQ

What measuring range do these pins cover?
The pins cover a 100–250 mm measuring span and are matched to internal gauging tasks within that range.

Are these pins compatible with the 208.027 gauge?
Yes — the 4‑piece measuring pins for 208.027 (100–250 mm) are designed specifically for compatibility with the 208.027 mounting and fit the instrument’s M8/7.2 interface.

How many pins are included in one set?
One set contains four individual measuring pins, supplied as a ready‑to‑use accessory pack under SKU M208.027.BZ.

Is the item traceable for inventory systems?
The product is identified by GTIN 4054469146683 and the SKU M208.027.BZ to support procurement and traceability.

Can these pins affect probe load and measurement stability?
The low mass (0.02 kg) of the pins minimises additional probe load, which helps maintain measurement stability and repeatability during short inspection cycles.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com