10 mm Edge Probe Rotating Spindle Max Speed 600 rpm, 10 mm Shank - Metav IndustryLine

Take advantage of the combination of 0.01 mm precision, a rotating spindle and a compact 10 mm stylus for reliable edge detection and faster set-up. Order the probe directly via Metav Werkzeuge or ask the Metav consultants for integration advice.

M208.095 edge probe — rotating spindle, Ø 10 mm stylus (Metav IndustryLine)

The M208.095 edge probe is a compact rotating‑spindle sensor designed for precise edge detection and quick workpiece alignment on machine tools and coordinate measuring machines

• Rotating spindle for edge detection
• 10 mm stylus and 10 mm shank
• High accuracy 0.01 mm
• Max 600 rpm for fast indexing

Speed up set-up and reduce rework

A rotating measuring spindle combined with a compact 10 mm stylus enables reliable contact geometry and short detection cycles, which reduces set‑up time at the machine. The unit's declared 0.01 mm accuracy provides measurable improvement in repeatability for reference‑edge finding; this translates directly into fewer trial cuts and less scrap. By converting precise detection into reproducible offsets, the sensor supports shorter cycle times and a steadier production flow, making process optimisation quantifiable rather than anecdotal.

Engineered for reliable sensing in production

The probe's rotating spindle and solid 10 mm shank deliver consistent contact orientation, even during quick indexing at up to 600 rpm. With a compact overall length and low mass (0.09 kg) the device minimises inertia while remaining rigid enough for routine shopfloor use. These characteristics suit the sensor to frequent tool changes and multi‑position checks where both speed and measurement integrity are required. The design therefore balances robustness with the agility needed in high‑mix, medium‑volume environments.

Integration that keeps operations moving

Installation is straightforward where a 10 mm mounting interface is used; the probe integrates with standard probe holders and tool posts, enabling rapid deployment without complex adaptors. The compact form factor supports close‑quarter probing in fixtures and tight setups while the rotating spindle simplifies angular alignment tasks. The result is a pragmatic tool for workshops seeking dependable edge sensing, better first‑pass yield and reduced non‑productive time. The M208.095 from Metav IndustryLine combines these practical gains with Metav’s quality filter for European deliveries.

For a tailored integration plan or a technical consultation on the M208.095, contact Metav Werkzeuge in Emmerich to discuss installation options and compatibility with existing probing systems.

Technical Data

• Article number: M208.095
• GTIN: 4054469104461
• Category: 3D touch probe
• Brand: Metav IndustryLine
• Tariff number: 84669340
• eClass: 21170311
• ETIM: EC000029

Facts

• Accuracy: 0.01 mm
• Weight: 0.09 kg
• Length: 84 mm
• Stylus diameter: 10 mm
• Shank diameter: 10 mm
• Max rotational speed: 600 rpm

Special features

• Rotating measuring spindle
• Taster / stylus Ø 10 mm
• Mounting/shank 10 mm
• Suitable for edge detection and workpiece alignment
• Category: 3D probe

FAQ

What is this probe primarily used for?
The M208.095 is intended for precise edge detection and workpiece alignment on machine tools and coordinate measuring machines, enabling rapid locating of reference edges and centres.

What accuracy can be expected when using this probe?
The probe provides an accuracy of 0.01 mm, delivering repeatable measurements suitable for set‑up and process control tasks.

Which stylus and mounting sizes are specified?
The device uses a 10 mm stylus and a 10 mm mounting/shank, matching common probe holders and tool posts.

Is the measuring spindle rotating and what is the maximum speed?
Yes — the measuring spindle is rotating and the maximum indexing speed is 600 rpm, which aids fast angular alignment and indexing operations.

How compact and lightweight is the probe for use in tight fixtures?
With a length of 84 mm and a mass of 0.09 kg, the probe is designed for confined spaces and reduces handling inertia during frequent checks.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com