0-100 HA Digital Shore A Hardness Tester 0.5 Resolution Flat Cone Tip Ø0.79mm 35° IP54 - Metav IndustryLine
€55.00
Product information "0-100 HA Digital Shore A Hardness Tester 0.5 Resolution Flat Cone Tip Ø0.79mm 35° IP54 - Metav IndustryLine"
Take advantage of accurate Shore A measurement and simple digital operation for fast material checks in production and quality control; the device’s compact tip and lightweight design keep handling consistent across repeated tests. Order the unit directly via Metav Werkzeuge or consult their specialists for application advice.
Digital Shore hardness tester M208.351.N — Handheld Shore A gauge with 0–100 HA range and 0.5 HA resolution (Metav IndustryLine)
The Digital Shore hardness tester M208.351.N serves as a portable solution for rapid hardness screening on elastomers and soft plastics, combining a clear display with a compact measurement tip for confined test points.
- Range 0–100 HA for elastomers
- Resolution 0.5 HA for clear readings
- Flat cone tip Ø0.79 mm, 35° geometry
- Digital display with zero and hold buttons
Reliable results for process control and QA
The instrument delivers repeatable Shore A readings across the 0–100 HA range, enabling consistent pass/fail decisions within production. The 0.5 HA increment on the digital display gives a clear numerical basis for statistical process control or incoming goods inspection, reducing subjective interpretation. As a handheld hardness gauge, it suits line-side quality checks where quick throughput and documented numerical values matter more than laboratory turnaround times.
Designed for straightforward handling and confined test points
A flat cone tip Ø0.79 mm, 35° geometry concentrates the contact area, making it practical for small test fields and moulded parts. The unit’s lightweight (0.1 kg) construction supports stable single-handed operation while limiting operator fatigue during repeated measurements. Controls include dedicated on/off, zero and hold functions, which simplify measurement routines and let teams capture transient values without additional equipment.
Application compatibility and material scope
Measurement is performed according to Shore A methodology and is therefore intended for rubber, elastomers and other soft plastics such as neoprene, silicone, vinyl, felt and leather. The specification favours surface-sensitive checks and comparative testing during production runs, helping to classify compounds by hardness and to identify batch deviations early in the process.
Practical delivery and workshop integration
The tester is supplied complete with a protective transport case, making it straightforward to store or carry between benches and production cells. The compact form factor and the clear readout integrate easily into routine inspection workflows, and the device’s simplicity supports training of shop-floor operators without a steep learning curve.
For tailored technical advice or to request specification matching for the Metav IndustryLine Digital Shore hardness tester (SKU M208.351.N), contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930
Technical data
- Article number: M208.351.N
- GTIN: 4054469162669
- Tariff number: 90241040
- Manufacturer: Metav IndustryLine
Core measurements
- Measurement range: 0–100 HA
- Resolution: 0.5 HA
- Tip diameter: Ø0.79 mm
- Tip angle: 35°
- Weight: 0.1 kg
Special features
- Measurement method: Shore A
- Display: digital with on/off, zero and hold
- Suitable for: rubber, elastomers, neoprene, silicone, vinyl, felt, leather
- Supplied in a protective transport case
FAQ
What hardness range does the tester cover?
The device measures within a 0–100 HA range, suitable for most elastomers and soft plastics.
What is the resolution of the readings?
Readings are shown in 0.5 HA increments on the digital display for clear numerical comparison.
Which materials can be tested with this Shore A instrument?
The tester is intended for rubber and soft plastics, including neoprene, silicone, vinyl, felt and leather.
Is the tip suitable for small test points?
Yes; the flat cone tip Ø0.79 mm, 35° is designed for compact test areas and moulded features.
Is a calibration certificate supplied with the product data provided?
The supplied product information does not specify a calibration certificate; the data shows the standard technical specification only.
Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
| Designation: | Shore-Härtemessgerät |
|---|
Vergleichsplatten
Take advantage of a compact reference range and consistent tolerance to speed up hardness checks and maintain production quality; combine 36–94 HA coverage with a repeatable ±2 HA tolerance for efficient verification. Order the set through Metav Werkzeuge or consult our specialists for application advice. M208.361 Shore A Comparison Plate Set — 7 calibrated reference plates, 36–94 HA, ±2 HA tolerance (Metav IndustryLine) The M208.361 Shore A Comparison Plate Set provides standardised hardness references for quick verification of Shore A durometers in rubber and elastomer quality control, enabling straightforward checks at incoming inspection or on the shop floor. Seven calibrated Shore A reference plates Covers 36–94 HA hardness levels Tolerance ±2 HA for quick checks Suitable for Shore A / A0 durometers Reliable reference for faster hardness verification The set delivers a compact selection of reference plates that simplify routine checks of durometers. With clearly defined steps across the hardness curve and a declared ±2 HA tolerance, this kit offers a pragmatic balance between specificity and convenience. Using comparison plates reduces the need for time‑consuming instrument recalibration during frequent spot checks, supporting a continuous inspection flow and helping to detect drift before parts leave the production line. The construction and nominal dimensions ensure consistent contact geometry for repeatable readings with handheld Shore testers. Broad hardness range matched to common materials Covering 36–94 HA, the plates span the most used range for elastomers, soft rubbers and many polymer blends, making the set suitable for verification tasks in rubber goods, seals, gaskets and similar components. The graded hardness steps assist in assessing whether a durometer reading sits within expected process limits, aiding swift pass/fail decisions. Lightweight and compact, the comparison set can be kept at the inspection station for immediate cross‑checks, reducing throughput interruptions and improving traceability of routine measurements. Practical handling for everyday quality routines Designed as a straightforward comparator tool, the set supports quick tactile comparisons and visual documentation of instrument condition. Plates are numbered and laid out for logical sequence checks, helping operators to perform consistent measurements with minimal training. The low mass and standardised face size allow stable contact with most handheld Shore A testers, improving reproducibility during successive readings. For workshops seeking an uncomplicated verification method, the set offers an economical way to uphold measurement confidence between formal calibrations. Contact Metav Werkzeuge for tailored advice on integrating the M208.361 into existing quality workflows or to confirm suitability for specific elastomer classes Technical Data SKU: M208.361 Manufacturer: Metav IndustryLine Weight: 0.1 kg Set composition: 7 pieces Facts Hardness values: 36, 42, 55, 67, 75, 85, 94 HA Tolerance: ±2 HA Dimensions (per plate): 50 x 50 x 8 mm Special features Suitable for Shore A / A0 durometers Comparison plates for verification of durometer readings Designed for routine inspection and quick checks FAQ What hardness levels are included in the set? The set includes reference plates at 36, 42, 55, 67, 75, 85 and 94 HA, allowing checks across a broad part of the Shore A scale. Is the M208.361 intended for Shore A durometers only? The M208.361 is configured for Shore A / A0 testers and is intended to verify readings for soft to medium elastomers and similar materials. How should the comparison plates be used for a verification check? Place the durometer on a chosen plate, allow the instrument to stabilise, and compare the reading with the known plate value; the M208.361 offers a practical means to identify drift between formal calibrations. Does the set replace formal calibration? No, the set serves as a verification tool for routine checks and condition monitoring; it does not replace traceable calibration procedures performed by accredited laboratories. Can the plates be used for documentation and quality records? Yes, the plates provide repeatable reference points useful for documenting instrument condition and supporting in‑process quality records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com