33/49/92 HD Shore D Comparison Plates Set, Three-Piece, ±2 HD Tolerance, Supplied in Case - Metav IndustryLine
€51.00
Product information "33/49/92 HD Shore D Comparison Plates Set, Three-Piece, ±2 HD Tolerance, Supplied in Case - Metav IndustryLine"
Benefit from a reliable set of Shore D reference plates offering hardness points of 33, 49 and 92 HD with a tolerance of ±2 HD, delivered in a protective transport case for safe handling — order the set directly via Metav Werkzeuge or consult our advisors for application guidance.
Shore D comparison plate set M208.362 — Metav IndustryLine reference plates with defined hardness points and transport case
The Shore D comparison plate set provides stable reference surfaces for verification of Shore D hardness testers, designed for routine checks in workshops and inspection environments.
- Reference plates for Shore D testers
- Hardness points 33 / 49 / 92 HD
- Tolerance up to ±2 HD
- Supplied in transport case
Reliable benchmark for routine hardness checks
The set functions as a concise, shop-floor benchmark to detect instrument drift and to verify measurement consistency. Each reference surface is specified at 33/49/92 HD and manufactured to a tolerance of ±2 HD, so readings can be compared quickly against stable reference points. Using defined hardness points simplifies daily acceptance checks and shortens the time needed to decide whether an instrument requires service or adjustment, supporting efficient quality control and reduced rework.
Compact, workshop-ready design with secure transport
With compact dimensions of 50 x 50 x 8 mm and a low mass, the plates are easy to handle and store. The three-piece set arrives in a protective transport case, minimising the risk of damage during storage or transfer between workstations. The small footprint and robust packaging make the set suitable for mobile inspections and shop-floor routines where space is limited but reliable references are required. The practical design keeps reference surfaces accessible and intact, preserving repeatability over time.
Practical integration into inspection and QC routines
These comparison plates provide clear, repeatable reference points that fit into existing hardness-testing procedures for elastomers and polymers measured on Shore D scales. Regular use of the set helps maintain measurement traceability within the workshop and supports decision-making in incoming inspection or final checks. The set is offered by Metav IndustryLine and is identified as M208.362, making it straightforward to order replacement or additional sets and to document which reference standard was used during an inspection.
For assured reference checks and shop-floor compatibility, request the Metav IndustryLine Shore D comparison plate set M208.362 via Metav Werkzeuge or contact our advisors at info@metav-werkzeuge.com / +49 2822 7131930 for application-specific guidance
Technical data
- Article number: M208.362
- SKU: M208.362
- Manufacturer: Metav IndustryLine
- Pieces per set: 3
- Weight: 0.1 kg
Facts
- Dimensions: 50 x 50 x 8 mm
- Hardness values: 33 HD, 49 HD, 92 HD
- Tolerance: ±2 HD
- Set weight: 0.1 kg
Special features
- Suitable for Shore D hardness testers
- Transport case included (plastic or wooden)
- Three reference plates for comparative checks
- Intended for routine verification and shop use
FAQ
Which hardness points are included in the set?
The set contains reference plates specified at 33 HD, 49 HD and 92 HD, intended as fixed comparison points for Shore D measurements.
What tolerance applies to the reference plates?
Each plate is manufactured to a tolerance of ±2 HD, providing defined limits for quick verification of instrument readings.
Can the plates be used on the shop floor and for mobile inspections?
Yes, the compact 50 x 50 x 8 mm plates and included transport case make the set suitable for workshop use and for carrying between inspection sites.
How many plates are supplied and how are they delivered?
The delivery comprises a three-piece set supplied in a protective transport case to safeguard the reference surfaces in transit.
Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
| Designation: | Vergleichsplatten-Satz |
|---|
Shore Messgerät
Take advantage of the combination of a clear digital display, a compact 0–100 HD measuring range and a precise conical probe (30° SR 0.1 mm) for fast, repeatable Shore D checks; order directly via Metav Werkzeuge or consult the specialists for application advice. Digital Shore Hardness Tester M208.353.N — Shore D, 0–100 HD range, 0.5 HD reading The Digital Shore Hardness Tester M208.353.N is a portable Shore D hardness gauge designed for quick hardness checks on plastics and related materials in production and incoming‑goods inspection. Digital display with ON/OFF, ZERO and HOLD Shore D method, 0–100 HD measuring range Conical probe 30° SR 0.1 mm Delivered in a plastic or wooden transport case Reliable Shore D readings for plastics and composites The instrument measures hardness according to the Shore D principle over a 0–100 HD scale, with a display graduation of 0.5 HD for immediate interpretation. This combination delivers a practical balance between resolution and speed: the larger step size compared with laboratory durometers speeds up inline spot checks while still allowing discernible differences between formulations and batches. The conical probe (30° SR 0.1 mm) concentrates the contact area for consistent penetration depth on semi-rigid plastics, resins and cast materials, reducing variability that can come from inconsistent probe contact. Ergonomic design that supports consistent testing Built for handheld operation, the tester weighs just 0.1 kg, making it easy to position against samples without excessive operator fatigue. The digital display is supported by three dedicated controls — ON/OFF, ZERO and HOLD — which help standardise the measurement sequence and capture readings for later documentation. A lightweight instrument and clear controls reduce handling errors, so measurements become more repeatable across different operators and shifts. Delivery in a transport case protects the unit in transit and provides practical storage between uses. Fits routine quality workflows and shop‑floor checks With an emphasis on fast, comparative testing, the device integrates smoothly into manufacturing and quality assurance routines where plastics, epoxy compounds and acrylics are inspected. The gauge’s technical identifiers (SKU M208.353.N, GTIN and eClass) support inventory and traceability procedures; recorded results from the unit can be used to monitor process stability and support decision making on material acceptance. The tester’s specification is tuned for production control rather than laboratory certification, offering a pragmatic tool to maintain consistent product properties without complex instrumentation. For straightforward, repeatable Shore D checks, choose the Metav IndustryLine tester and obtain delivery from Metav Werkzeuge — contact their consultants for application matching and supply from the Emmerich quality hub Technical data Article number: M208.353.N GTIN: 4054469162676 eClass: 21170518 Customs tariff number: 90241040 Facts Measurement range: 0–100 HD Resolution / reading: 0.5 HD Accuracy: 2 Weight: 0.1 kg Special features Measuring method: Shore D Measuring tips: cone 30°; SR 0.1 mm Digital display with ON/OFF, ZERO and HOLD Suitable for: plastics, resin, epoxy, Plexiglas Delivered in plastic or wooden transport case FAQ How does the tester determine Shore hardness? The Digital Shore Hardness Tester M208.353.N uses a Shore D indenter to measure resistance to indentation and displays the result on its digital screen in HD units. What materials can be tested with this gauge? Typical applications for the tester include plastics, resins, epoxy compounds and Plexiglas, where Shore D is the appropriate hardness scale. What resolution and accuracy can be expected? The instrument displays readings at 0.5 HD resolution; the supplied specification lists an accuracy indicator of 2 as provided in the product data. Is the unit suitable for shop‑floor use and transport? Yes — the device is lightweight (0.1 kg) and is supplied in a protective plastic or wooden transport case for safe handling and storage. Which probe geometry does the instrument use? The tester is fitted with a conical measuring tip at 30° with an SR of 0.1 mm, designed for consistent contact on semi‑rigid materials. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com