20mm Tapered Measuring Cone, Offset 300mm, b50 a112 - Metav IndustryLine

Take advantage of precise alignment and repeatable positioning thanks to the combination of a 20 mm cone tip and compact geometry (b = 50 mm, a = 112 mm), which speeds up fixture set-up and reduces measurement variation. Order the measuring cone directly via Metav Werkzeuge or consult the product specialists for compatibility advice.

Measuring cone 20 mm for 240.293 — precision cone for fixture alignment (Metav IndustryLine)

The measuring cone 20 mm for 240.293 is a dedicated alignment accessory designed to work with the M240.293 measuring fixture; it provides a defined contact point for repeatable positioning in systems with a 300 mm hole spacing.

• 20 mm cone diameter for defined contact
• Compatible with M240.293 measuring system
• Lightweight construction for simple handling

Faster, repeatable set-ups through defined contact geometry

The conical tip with a 20 mm diameter establishes a precise contact interface that reduces positional ambiguity when locating holes or reference points on a fixture. Matched to the M240.293 system and its hole spacing of 300 mm, the shaped contact reduces re‑clamping time and supports consistent measurement chains. This mechanical definition translates into fewer alignment iterations and a lower risk of cumulative error in production or inspection workflows, improving throughput in metrology‑driven applications.

Compact form and ergonomic handling for workshop use

With segment dimensions of b = 50 mm and a = 112 mm, the accessory remains compact while offering sufficient reach for many fixture geometries. The low mass (approx. 0.2 kg) makes handling straightforward during frequent set‑up changes and minimises the effect of operator fatigue on process speed. The concise dimensions are particularly suitable where a clear datum point is required without adding excessive overhang or leverage that could affect stability during measurement.

Practical applications and integration with inspection processes

Designed as an accessory for bench and fixture metrology, the cone supports reliable centring and reference establishment for both component set‑up and follow‑up inspection. The defined geometry aids optical or tactile measurement systems by providing a consistent mechanical reference, which helps to reduce scatter between successive readings. Integration with standard measuring rigs is simplified by the explicit compatibility with the M240.293 designation and the matching 300 mm hole pattern, enabling smooth incorporation into established inspection procedures.

For assured compatibility and supply of Metav IndustryLine accessories, contact Metav Werkzeuge to request the M240.293.A measuring cone or advice on fixture integration; consultants are available at info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: M240.293.A
• GTIN: 4061905053801
• Label: Messkegel 20 mm for 240.293 (Bohrabstand‑MS 300 mm)

Facts

• Cone diameter: 20 mm
• Length a: 112 mm
• Length b: 50 mm
• Weight: 0.2 kg
• Hole spacing (MS): 300 mm

Special features

• Compatible with M240.293 measuring system
• Defined contact geometry for repeatable positioning
• Compact design for workshop and fixture use

FAQ

What is the primary purpose of this measuring cone?
The measuring cone provides a defined contact point for repeatable positioning and alignment within M240.293‑based fixtures, helping to reduce setup time and measurement variation.

Is the cone compatible with existing M240.293 fixtures?
Yes, the cone is listed for use with the M240.293 measuring system and matches the 300 mm hole spacing specified for that fixture family.

What are the physical dimensions and weight of the cone?
The cone features a 20 mm tip diameter with segment lengths of 50 mm and 112 mm respectively and weighs approximately 0.2 kg.

Can this accessory improve throughput in inspection routines?
When used as a defined mechanical reference in a metrology set‑up, the cone contributes to faster, more repeatable set‑ups and can reduce the need for repeated adjustments during inspection.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com