1–2mm Test Probe Holder Green Aluminium Anodised, Single-Sided - Metav IndustryLine

Take advantage of precise, repeatable probe positioning combined with a corrosion‑resistant, lightweight design to keep inspection routines efficient. Order directly via Metav Werkzeuge or consult the team for compatibility advice.

Measuring Pin Holder GO (1–2 mm) – Single‑sided probe holder in anodised aluminium (Metav IndustryLine)

A Measuring Pin Holder GO (1–2 mm) for secure, single‑sided mounting of measuring pins in gauge fixtures and inspection setups.

• Anodised aluminium construction for corrosion resistance
• Green 1–2 mm insert for precise centring
• Single‑sided design for gauge fixtures
• Compact 46 mm length for tight assemblies

Consistent clamping for repeatable measurements

The holder delivers secure mounting of measuring pins with diameters of 1–2 mm, reducing slippage and angular error during inspection cycles. By fixing the pin in a dedicated receptacle, the component minimises run‑out and enables tighter process tolerances; this leads to fewer re‑measurements and a steadier quality control throughput. The compact form factor and straightforward geometry make the part suitable for dense fixturing where reproducible contact is essential.

Durable material choice that eases integration

Constructed from anodised aluminium, the unit combines low mass with corrosion resistance to withstand regular handling and exposure to shop‑floor environments. The green insert marks the locating interface and provides precise centring for small‑diameter pins, while the shallow profile (46 mm overall length and 9 mm width) enables installation in narrow pockets or on bespoke gauge plates. The lightweight design reduces added inertia on moving fixtures and simplifies handling during assembly and exchange.

Reduces downtime through simple handling and replacement

The single‑sided format supports fast installation and replacement of measuring pins, accelerating routine maintenance and gauge setup. Where rapid changeover is required, the holder allows the use of standard 1–2 mm pins without the need for special adaptors, which shortens fixture preparation times and contributes to higher machine uptime. Clear visual identification via the coloured insert helps maintenance staff locate the correct receptacle quickly, supporting lean processes on the inspection bench.

Practical suitability for workshop and inspection environments

As a compact fixture component, the holder is appropriate for small gauge assemblies and larger inspection rigs where multiple probe positions are required. The aluminium construction offers a favourable strength‑to‑weight ratio while remaining compatible with standard workshop cleaning and handling practices. Sourcing through Metav IndustryLine guarantees consistent stock levels and a reliable supply chain for repetitive purchases in production environments.

Contact Metav Werkzeuge for application-specific recommendations and ordering of the Metav IndustryLine measuring pin holder to ensure correct fitment in gauges and fixtures

Technical Data

• Article number: M318.566.2
• Brand: Metav IndustryLine
• Product: Measuring pin holder GO (1–2 mm)
• Colour: green
• Material: anodised aluminium
• Orientation: single‑sided

Dimensions & measurable data

• Width: 9 mm
• Length: 46 mm
• Compatible pin diameter: 1–2 mm

Features & compatibility

• Anodised aluminium construction
• Green centring insert for 1–2 mm pins
• Designed for gauge and fixture mounting
• Compact profile for tight assemblies

FAQ

What pin diameters are supported by this holder?
The measuring pin holder accepts 1–2 mm measuring pins and is designed to centre and secure them for inspection use.

Is the holder suitable for gauge fixtures in mass production?
Yes, the Metav IndustryLine holder is intended for repeated fixture use; its anodised aluminium body and compact design support durable, repeatable mounting in production environments.

Can the centring insert be replaced if worn?
The green centring insert is a defined locating feature; replacement depends on fixture design and pin accessibility—refer to Metav Werkzeuge guidance for recommended maintenance intervals.

Does the product require any special installation tools?
Standard workshop tools suffice for mounting the holder into gauge plates or fixture blocks; no specialised equipment is necessary for routine installation.

Is the component compatible with all standard 1 mm and 2 mm probe pins?
The holder is made for standard 1–2 mm probe pins; compatibility with a particular pin design should be verified against the pin seating geometry and any applicable fixture tolerances.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com