3-4mm Ceramic Gauge Pin Set 0.01mm Steps, Stainless Zirconia, HV1250, Holder, Plastic Case - Metav IndustryLine

Take advantage of the combination of zirconia ceramic robustness, sub‑micron accuracy and workshop‑ready packaging for reliable bore checking and repeatable gauging; order the ceramic gauge pin set directly via Metav Werkzeuge or ask our consultants if needed.

Ceramic Gauge Pin Set, 101-piece (3.00–4.00 mm, 0.01 mm steps) — Metav IndustryLine

A Ceramic Gauge Pin Set designed for precise plug gauging and fine mechanical inspection across the 3.00–4.00 mm range with 0.01 mm increments

• Zirconia ceramic, antimagnetic and wear‑resistant
• High hardness HV 1250 for long service life
• Precision tolerance < ±0.0015 mm
• Supplied with holder and plastic case

Repeatable high‑precision measurement where it matters

The set is built from zirconia ceramic, a material that combines low wear, corrosion resistance and inherent antimagnetic properties; this makes it especially suitable for measurements where steel pins could introduce magnetic interference or wear quickly. With an indicated accuracy < ±0.0015 mm and a graduation of 0.01 mm, the pins deliver very tight tolerances that support confident go/no‑go assessments and dimensional verification in laboratory and production settings. The stated HV 1250 hardness explains the long service life and the low wear rate under normal gauging loads, reducing the frequency of replacement and maintaining consistent measurement results over time.

Workshop practicality and handling benefits

Supplied in a compact plastic case with an integrated measuring pin holder and presented in a workshop specification at 50 mm shank length, the set is optimised for everyday use on the shop floor. The case keeps the pins organised and protected during transport and storage, while the holder speeds up changeover between sizes, reducing cycle time for repetitive inspections. The compact design and non‑metallic composition make the tooling light to handle and simple to integrate into existing inspection benches or portable checking kits, helping to maintain throughput without compromising on measurement fidelity.

Applications where non‑magnetic, stable gauging improves results

This kit supports precise plug gauging, bore verification and match‑testing of micro components—fields such as precision engineering, horology, optical assembly and fine‑mechanics benefit from a non‑corroding, dimensionally stable gauge material. The sub‑micron class tolerance is particularly valuable when acceptance criteria demand minimal clearance or when comparing mating components over multiple production runs. Metav’s emphasis on accessible precision means this solution is offered with the practicality and supply reliability expected by workshops and production facilities across Europe.

For workshop enquiries or to order this Metav IndustryLine ceramic gauge pin set directly from Metav Werkzeuge, contact our specialists in Emmerich for tailored advice and delivery options

Technical Data

• Article number: M318.593
• Description: Ceramic gauge pin set, 3.00–4.00 mm, 0.01 mm steps
• Range: 3.00–4.00 mm
• Increment: 0.01 mm
• Hardness: HV 1250
• Accuracy: < ±0.0015 mm
• Length: 50 mm
• Pieces: 101

Facts

• Measurement range: 3.00–4.00 mm
• Step size: 0.01 mm
• Maximum stated tolerance: < ±0.0015 mm
• Hardness: HV 1250
• Shank length: 50 mm
• Set size: 101
• SKU: M318.593

Special features

• Material: zirconia ceramic
• Antimagnetic
• Wear‑resistant
• Workshop execution
• With measuring pin holder
• Supplied in plastic case
• Intended for precise plug gauging and fine mechanical inspection

FAQ

What measurement range does this gauge pin set cover?
The ceramic gauge pin set covers the 3.00–4.00 mm range with 0.01 mm increments for fine‑step checking.

Is the material suitable for use near magnetic fields?
Yes. The pins are made from zirconia ceramic, which is antimagnetic and therefore suitable where magnetic interference must be avoided.

How precise are the pins and what tolerance can be expected?
The pins are specified with an accuracy of < ±0.0015 mm, making them suitable for demanding dimensional checks and close‑fit assessments.

Does the set include storage and handling accessories?
The kit is supplied in a plastic case and includes a measuring pin holder for rapid handling and secure storage.

Which industries or applications benefit most from this kit?
Precision engineering, horology, optical and micro‑mechanical assembly benefit from the non‑corroding, low‑wear ceramic pins and their tight tolerances; the Metav IndustryLine set (SKU M318.593) is geared towards these uses.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com