Ø40x200 HSK-A/E40 Test Mandrel D25 L200 0.003 mm Runout Accuracy, ISO 12164/DIN 69893 - Metav IndustryLine

The combination of an HSK‑A/E40 interface, hardened gauge steel body and runout <0.003 mm ensures reproducible spindle alignment and reduced setup times. Take advantage of accurate, durable measuring geometry and order the test mandrel directly via Metav Werkzeuge or ask our consultants if needed.

Test Mandrel HSK‑A/E40‑D25‑L200 — HSK gauge mandrel with <0.003 mm runout

The Test Mandrel HSK‑A/E40‑D25‑L200 is a precision gauge for spindle runout verification and fine alignment tasks in machine shops and toolrooms

• HSK‑A/E40 interface, 25 mm drive
• Runout <0.003 mm for precise alignment
• Hardened gauge steel, HRC 58
• Complies with ISO 12164 / DIN 69893

Precision that shortens machine setup and rework

The mandrel delivers a quantified runout <0.003 mm, making it a rational choice for shops that need reproducible spindle checks. By providing a reliable reference geometry via the HSK‑A/E40 interface, the tool reduces iterative alignments and minimises scrap caused by spindle eccentricity. Measured errors can thus be addressed earlier in the setup process, improving first‑part yield and lowering total process time. The focus here is on measurable improvement in productivity rather than subjective claims.

Robust construction for repeatable measurements

Constructed from hardened gauge steel and specified at HRC 58, the mandrel resists wear and maintains a stable datum over repeated use. The nominal dimensions Ø40×200 and the 25 mm shank provide a balance between stiffness and handling: sufficient mass for stable contact while remaining manageable on the workshop bench. The hardened material reduces profile change over time, so the reference geometry stays consistent and calibration intervals can be planned with confidence.

Standards conformity for traceable results

Built to ISO 12164 / DIN 69893 standards, the device supports documented quality routines and inspection procedures. Conformance to these norms simplifies integration into existing test protocols and audit trails, enabling clear traceability of alignment checks. The gauge is intended for routine runout verification and alignment of machine spindles and serves as a reliable datum when comparing successive measurements or validating spindle rebuilds.

Practical workshop use and application scenarios

The mandrel is suited to spindle runout checks, alignment of toolholding systems and comparative testing after maintenance. Its balanced geometry and interface allow quick installation into HSK‑A/E40 spindles so that alignment can be verified with standard dial indicators or electronic probes. For operations seeking to reduce machine downtime and avoid repeated part rework, this gauge supplies a measurable reference that supports faster decision making on setup quality.

For application advice or to place an order, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific spindles and fixtures

Technical Data

• Article number: M318.922
• GTIN: 4054469183886
• Type: HSK‑A/E40‑D25‑L200
• Material: Hardened gauge steel
• Standard: ISO 12164 / DIN 69893

Facts

• Weight: 2 kg
• Hardness: HRC 58
• Runout / cylindricity: <0.003 mm
• Dimensions: Ø40 × 200 mm
• Shank / drive: 25 mm

Special features

• Intended use: Spindle runout verification and alignment
• Category: Gauges
• Durable reference geometry for repeated use
• Suitable for machine shop and toolroom applications

FAQ

What runout accuracy can be expected with this mandrel?
The Test Mandrel HSK‑A/E40‑D25‑L200 (M318.922) provides a measured runout/cylindricity of <0.003 mm, suitable for high‑precision spindle checks.

Which spindle interface does the gauge use?
This gauge is designed for the HSK‑A/E40 interface and uses a 25 mm drive for secure seating in compatible toolholders.

Is the mandrel suitable for routine shop use?
Yes — the hardened gauge steel construction and robust geometry make the tool appropriate for regular spindle inspections and alignment tasks in production environments.

Does the mandrel conform to industry standards?
The device complies with ISO 12164 / DIN 69893, facilitating integration into standard inspection procedures and quality documentation.

How is the mandrel typically used during alignment work?
The mandrel is mounted in the spindle to provide a precision reference; runout can then be checked with a dial indicator or probe to verify concentricity and take corrective action if required.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com