0.33mm Gauge Pin, 40mm Probe Length, ±0.002mm Accuracy, Workshop Version, Plastic Case - Metav IndustryLine

Take advantage of the combination of high repeatability, compact geometry and robust special steel for reliable end-measurements; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice.

M323.033 Gauge Pin – Ø 0.33 mm, ±0.002 mm (Metav IndustryLine)

The M323.033 gauge pin is a single precision probe designed for fine end‑measurements and calibration checks in workshop and inspection contexts.

• Workshop version for frequent inspection
• Diameter Ø 0.33 mm with tight tolerance ±0.002 mm
• Compact pin and overall lengths for small bores
• Manufactured from special steel for durability

Reduce measurement uncertainty with defined tolerance

The small diameter and tight tolerance of ±0.002 mm make this gauge pin ideal where repeatable end‑measurements are required. The fine nominal diameter Ø 0.33 mm minimises probe interference in confined bores, while the specified tolerance defines the permissible deviation during inspection. This precision supports faster decision‑making in quality control, since measurements can be directly compared to drawing tolerances without additional correction factors. The clear numerical specification offers a verifiable basis for inspection planning and traceable acceptance criteria.

Compact geometry and durable material for repeatable checks

Designed as a single probe item, the pin features a pin length of 40 mm and a total length of 57 mm, combining reach with stable handling during manual checks. The component is made from special steel, which supports wear resistance under regular use and preserves the measuring geometry for longer service life. The light mass (approx. 0.003 kg) and workshop execution ensure easy handling on benches or in fixtures; the compact form helps maintain alignment in micro‑diameters and reduces bending moments that could otherwise affect repeatability.

Practical fit for metrology and small‑part inspection

Built for routine verification and end‑dimension checks, this gauge pin is suitable for small‑bore inspection, micro‑component verification and fine mechanical assembly controls. The simple, single‑piece configuration allows quick interchange in test rigs and manual plug checks, increasing throughput in serial inspection tasks. As a defined measuring tool, it integrates cleanly into documented inspection procedures and supports consistent quality documentation across batches.

For precision end‑measurements select the Metav IndustryLine M323.033 gauge pin and contact Metav Werkzeuge for tailored procurement or technical clarification at info@metav-werkzeuge.com or +49 2822 7131930

Technical data

• Article number: M323.033
• GTIN: 4061905054006
• Label: Prüfstift, einzeln, 0,33 mm, +/- 0.002 mm Stiftlänge 40, Gesamtlänge 57 mm

Facts

• Diameter: Ø 0.33 mm
• Tolerance: ±0.002 mm
• Pin length: 40 mm
• Total length: 57 mm
• Weight: 0.003 kg

Special features

• Workshop version (workshop execution)
• Single gauge pin (individual item)
• Material: special steel
• Story trigger: end‑measurements

FAQ

What tolerance does the gauge pin offer?
The M323.033 gauge pin is specified with a tolerance of ±0.002 mm for its nominal diameter.

What are the diameter and lengths of this probe?
The probe has a diameter of Ø 0.33 mm, a pin length of 40 mm and a total length of 57 mm.

What material is the pin made from?
This gauge pin is manufactured from special steel to provide durability and stable measuring geometry.

Is the item intended for workshop use?
Yes, the M323.033 is offered as a workshop version suitable for frequent inspection tasks and bench use.

Which inspection tasks is this pin best suited for?
The pin is particularly suitable for end‑dimension verification of small bores, micro‑components and fine mechanical assemblies.

Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com