32mm Magnetic Flat Gripper H7 No Threaded Bush Holding Force 80N - TECWERK
Take advantage of a compact design with reliable 80 N holding force and hard ferrite construction for steady, low-profile temporary fixing; order directly via Metav Werkzeuge or consult the Metav team for application advice. Flat magnetic gripper D32×H7 mm – 80 N, TECWERK The Flat magnetic gripper D32×H7 mm is a compact, ceramic magnet designed for secure temporary fastening and positioning in light-duty assembly, fixture and automation applications. *Compact 32 mm diameter for tight spaces Reliable 80 N maximum holding force Hard ferrite material for thermal stability Designed without threaded bush for flush mounting Consistent clamping with measurable holding force The flat magnetic gripper delivers a clear 80 N holding force, providing a predictable clamping action for small components and jigs. The specified holding capacity enables planners and engineers to calculate safety margins and define handling procedures with confidence. As a passive magnetic element, the component offers immediate magnetic attraction without additional actuation, which simplifies fixture design and reduces the number of moving parts required for temporary fastening. The compact footprint supports integration where space is constrained. Temperature-resistant, low-maintenance material choice Constructed from hard ferrite, this magnet affords good thermal resistance compared with many polymer-bonded alternatives. The product is rated with a recommended operating temperature up to 100 °C and a maximum of 200 °C, making it suitable for elevated-temperature assembly processes and short-term exposure to heat during production. Hard ferrite is a ceramic magnetic material that maintains magnetic characteristics at higher temperatures while remaining chemically stable; however, designers should consider the material's brittleness when specifying mechanical interfaces or impacts. Low-profile installation and straightforward integration With a 32 mm diameter and 7 mm overall height, the unit is engineered for flush mounting and minimal protrusion from fixture surfaces. The version supplied without a threaded bush reduces overall thickness and allows direct bonding, countersinking or clamping into shallow recesses in tooling plates. This low profile facilitates closer stacking of components and conserves valuable toolroom real estate. Integration into light-duty assembly rigs or positioning stations is therefore simpler and more space-efficient. For robust, space-saving magnetic holding in small-assembly tasks choose the TECWERK flat magnetic gripper and contact Metav Werkzeuge for bespoke advice and supply from Emmerich. Technical data Article number: 4000832235NW Product type: Flat magnetic gripper Brand: TECWERK Version: without threaded bush Facts Diameter: 32 mm Height: 7 mm Holding force max: 80 N Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C Special features Material: hard ferrite Packaging unit: 10 Compact, low-profile design FAQ What holding capacity does the gripper provide? The TECWERK flat magnetic gripper provides a maximum holding force of 80 N, suitable for securing small parts and fixtures in light-duty applications. Is the magnet suitable for elevated temperatures? Yes. The unit is constructed from hard ferrite and is recommended for use up to 100 °C with a maximum permissible temperature of 200 °C for short exposures. How is the gripper mounted if it has no threaded bush? The version without a threaded bush is intended for flush mounting into shallow recesses, bonding or clamping within tooling plates to achieve a low-profile installation. What are the exact dimensions of the component? The gripper measures 32 mm in diameter with a height of 7 mm, providing a compact footprint for tight assembly spaces. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
32mm Magnetic Flat Gripper With Threaded Bush, Holding Force 80N, Up To 200°C - TECWERK
Take advantage of a compact, reliable magnetic hold combined with straightforward mounting and heat tolerance for efficient fixturing and short setup times; order directly via Metav Werkzeuge or contact our consultants for specification support. Magnetic flat gripper D32×H15 mm (M4) — 80 N holding force by TECWERK The magnetic flat gripper D32×H15 mm with an M4 threaded bush provides compact, non-powered holding for fixtures and small assemblies. Compact 32 mm diameter, 15 mm height Secure M4 threaded bush mounting 80 N holding force for stable fixturing Hard ferrite magnet for consistent performance Space-saving, high-hold fixturing for production The Magnetic flat gripper D32×H15 mm with M4 threaded bush and 80 N holding force is engineered for applications where a small footprint and reliable clamping are required. With a 32 mm diameter and 15 mm height, the unit occupies minimal space while delivering a rated 80 N of holding force — a practical balance between size and performance. The hard ferrite construction ensures magnetic stability under normal workshop conditions, while the compact form supports dense arrangements on assemblies and jigs. This makes the component suitable for repetitive assembly tasks, small-part fixturing and conveyor positioning where a consistent magnetic hold reduces repositioning and handling time. Fast, secure mounting and reduced setup time Mounting is simplified by the integral M4 threaded bush, which permits direct fastening into fixtures, plates or machine guards without additional adapters. The threaded insert secures the magnet mechanically, allowing rapid installation and minimal alignment effort in production setups. Because the gripper is non-powered, there is no need for wiring or pneumatic control, which shortens commissioning and lowers maintenance requirements. The combination of mechanical fixation and magnetic holding reduces the need for additional clamps, helping to streamline changeovers and increase throughput in workshops and small production runs. Temperature performance and workshop resilience The unit is specified with a recommended operating temperature of up to 100 °C and a maximum of 200 °C, offering resilience where elevated temperatures occur during processing or near heated tooling. The hard ferrite material provides stable magnetic properties across the stated temperature range; appropriate selection of the operating point will extend service life and maintain holding capacity. Supplied in a packaging unit: 10, the grippers are practical for batch replacement or equipping multiple stations. The robust, simple design supports routine industrial use while keeping handling and inventory straightforward. For dependable, compact magnetic fixturing choose the TECWERK magnetic flat gripper—contact Metav Werkzeuge for tailored advice and prompt dispatch from Emmerich. Technical data Article number: 4000832245NW Product type: Magnetic flat gripper Manufacturer: TECWERK Dimensions & core data Diameter: 32 mm Height: 15 mm Thread: M4 Holding force: 80 N Packaging unit: 10 Materials & operating conditions Material: Hard ferrite Version: with threaded bush Recommended operating temp: up to 100 °C Maximum operating temp: 200 °C FAQ What holding force does the gripper provide? The TECWERK magnetic flat gripper delivers a rated holding force of 80 N (SKU 4000832245NW), suitable for secure retention of small ferrous components. How is the gripper mounted? Mounting is via the integrated M4 threaded bush; the M4 thread allows direct fastening into fixtures or plates for a stable mechanical connection. Which materials can be held by the magnet? The device is intended for ferromagnetic workpieces such as steel; the magnetic flat gripper provides a reliable hold for typical ferrous assemblies and small components. Can the gripper be used near heated tooling? Yes. The gripper is specified with a recommended operating temperature up to 100 °C and a maximum of 200 °C; observe the recommended limit for prolonged performance. Is this product suitable for series production and workshop use? The compact design, standard M4 mounting and consistent magnetic performance make the unit appropriate for workshop applications, jigs and small-series production fixtures. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
35mm Pot Magnet H.30mm With M6 Threaded Countersunk Hole Holding Force 147 N - TECWERK
Compact shape and high thermal tolerance make this pot magnet an efficient choice for fixtures and assembly tasks; its 147 N holding force and AlNiCo 500 composition ensure consistent performance under heat. Order the pot magnet directly via Metav Werkzeuge or ask our consultants for additional technical details. Pot magnet ⌀35 mm × 30 mm with M6 threaded blind hole — TECWERK The pot magnet ⌀35 mm × 30 mm with M6 threaded blind hole is a compact industrial holding solution designed for fixtures, jigs and secure temporary fastening in production environments. High holding force of 147 N AlNiCo 500 suitable to 450 °C M6 threaded blind hole for secure mounting Compact ⌀35 mm × 30 mm design Reliable holding performance in compact form The compact pot magnet delivers a predictable holding force of 147 N, making it suitable for light to medium clamping and positioning tasks where consistent magnetic grip is required. Constructed from AlNiCo 500, the unit offers good magnetic stability at elevated temperatures and maintains performance where other materials would weaken. The small footprint and robust magnetic core reduce the need for oversized fixtures, contributing to leaner tooling and fewer changeovers in assembly processes. Flexible mounting for workshop and industrial installation An integrated M6 threaded blind hole provides a secure, space-saving attachment point for bolts or studs without protruding thread interference, simplifying integration into machines, jigs or custom brackets. The blind-thread design also minimises collision risks in confined assemblies and allows fast replacement when wear occurs. With its compact diameter and low profile, the magnet is particularly suited to retrofitting existing setups or creating modular magnetic fixtures that shorten assembly time and improve repeatability. Temperature resilience and material predictability The magnet’s AlNiCo 500 alloy delivers stable magnetic characteristics across a wide temperature range; the specified maximum operating temperature of 450 °C supports demanding environments such as heat-treatment lines or near-painting ovens (lacquering processes up to 200 °C). This thermal resilience reduces the risk of demagnetisation in high-heat applications and ensures long-term reliability. The compact design and single-unit packaging also make stock management straightforward for workshops and procurement teams. Contact Metav Werkzeuge for availability, datasheets and application advice on the TECWERK pot magnet with 147 N holding force Technical data Article number: 4000832278NW Product type: Pot magnet Brand: TECWERK Material: AlNiCo 500 Execution: with threaded blind hole Dimensions & performance Diameter: 35 mm Height: 30 mm Thread: M6 Holding force: 147 N Max operating temperature: 450 °C Lacquering temperature: 200 °C Packaging & features Packaging unit: 1 Label: Topfmagnet D.35mm H.30mm m.Gewindesacklochbohrung Haftkraft 147 N BELOH SKU: 4000832278NW FAQ What holding capacity does this pot magnet offer? The pot magnet offers a maximum holding force of 147 N, suitable for light to medium clamping and positioning tasks in workshop and light industrial environments. Is the magnet suitable for high-temperature applications? Yes, the TECWERK pot magnet is made from AlNiCo 500 and is specified for use up to 450 °C, with a recommended lacquering temperature of 200 °C. How is the magnet mounted? Mounting is via an M6 threaded blind hole; the blind-thread configuration allows secure attachment without protruding threads, ideal for compact assemblies. What are the exact dimensions of the unit? The magnet measures ⌀35 mm in diameter with a height of 30 mm, supplied as a single unit (packaging unit: 1), SKU 4000832278NW. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
38.1mm Flat Cup Magnet With Through Hole And Countersink 130N Holding Force, AlNiCo 500 - TECWERK
Compact AlNiCo 500 construction together with a holding force of 130 N and a countersunk through bore delivers secure retention even in heated processes — ideal for fixtures that require both magnetic and mechanical attachment. Order the flat countersunk pot magnet directly via Metav Werkzeuge or ask our consultants if needed. TECWERK Flat countersunk pot magnet D 38.1 mm, 130 N holding force The flat countersunk pot magnet is a compact magnetic fastening element designed for industrial fixtures and high-temperature applications. AlNiCo 500 for elevated temperature use 130 N maximum holding force Countersunk through hole Ø 4.8 mm Compact diameter 38.1 mm for tight spaces Secure retention under heat for improved process reliability The magnet’s core advantage is its AlNiCo 500 alloy, which maintains magnetic performance at elevated temperatures up to 450 °C, reducing the risk of demagnetisation during thermal cycles. This characteristic translates into consistent clamping and positioning where temperature exposure is routine, such as in drying ovens or during coating processes. With a holding force of 130 N, the component provides measurable retention that supports steady assembly and handling, improving throughput and reducing rework. Reliable mechanical fixing for safe, flush mounting A countersunk through bore enables secure screw fastening in addition to magnetic grip, allowing a combined mechanical-magnetic attachment that prevents slippage on inclined or vibrating assemblies. The Ø 4.8 mm bore accepts common fasteners and the countersink allows the screw head to sit flush, preserving a low profile and preventing interference with adjacent parts. This design is particularly useful where a permanent or semi-permanent mounting is required alongside magnetic holding. Space-saving profile with paint-bake compatibility With a diameter of 38.1 mm and a low height of 10.4 mm, the unit is suitable for confined assemblies where a compact footprint is essential. The magnet also tolerates a coating bake temperature of 200 °C, enabling integration into painted or lacquered components without compromising adhesive processes. The compact form factor combined with thermal robustness supports efficient layout in jigs, fixtures and manufacturing aids, contributing to cleaner workflows and predictable results. For specification checks or application advice, Metav Werkzeuge’s technical team can be contacted by email or phone. Contact Metav Werkzeuge for personalised advice and secure procurement of this TECWERK flat countersunk pot magnet, ensuring the right mounting and temperature performance for the intended application Technical data Article number: 4000832272NW Facts Diameter: 38.1 mm Height: 10.4 mm Holding force: 130 N Bore diameter: 4.8 mm Maximum operating temperature: 450 °C Coating bake temperature: 200 °C Packaging unit: 1 Special features Material: AlNiCo 500 Execution: with through hole and countersink Product type: Flat countersunk pot magnet Manufacturer: TECWERK FAQ What maximum temperature can this magnet withstand before performance is affected? The TECWERK flat countersunk pot magnet (SKU 4000832272NW) is specified for continuous use up to 450 °C, which preserves magnetic stability in high-temperature processes. Can the magnet be fixed with a screw and still sit flush with the assembly surface? Yes. The unit features a countersunk through bore (Ø 4.8 mm) that allows a screw to be installed flush, combining magnetic holding with mechanical fastening for improved safety. What holding capacity can be expected from this magnet in standard conditions? Under standard conditions the magnet provides a holding force of 130 N; actual performance depends on mounting, substrate material and surface flatness. Is the magnet suitable for painted or powder-coated parts? The magnet tolerates a coating bake temperature of 200 °C, so it is compatible with many paint and lacquer processes provided the specified bake temperatures are not exceeded. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
40mm Flat Magnetic Gripper Without Threaded Bush Holding Force 125N, Temp Up To 200 °C - TECWERK
Take advantage of a compact, high‑force magnetic clamp that combines hard ferrite construction with a reliable 125 N holding force for small fixtures; order directly via Metav Werkzeuge or consult our specialists for integration advice. Magnetic flat gripper D.40xH8mm without threaded bush — compact hard ferrite clamp, 125 N holding force (TECWERK) Magnetic flat gripper D.40xH8mm without threaded bush for secure, space‑saving clamping in jigs, fixtures and light assembly applications Compact 40 mm diameter design Hard ferrite magnetic material 125 N holding force for secure clamping Withstands up to 200 °C peak temperature Precise clamping in a compact form for small assemblies The 40 mm diameter, low‑profile design delivers stable retention where space is limited. With a 125 N holding force, the component provides measurable clamping power while keeping bulk to a minimum. Built from hard ferrite, the unit is corrosion‑resistant for typical workshop conditions and designed for repeated placement in fixtures. The compact geometry supports accurate positioning and reduces the need for bulky clamps, which in turn can simplify jig design and save bench space. Consistent performance across normal operating temperatures Rated for a recommended operating temperature up to 100 °C and a maximum of 200 °C, the magnet is suitable for many light industrial environments where temperature exposure is intermittent. The temperature guidance helps predict changes in magnetic force over time and allows planners to choose an appropriate mounting strategy for processes involving heat. Clear temperature limits and material data enable a rational selection based on duty cycle rather than guesswork, supporting reliable process planning and fewer production interruptions. Flexible integration into fixtures thanks to a simple, threadless design The version supplied without a threaded bush offers a flush, unobstructed base that can be incorporated into bespoke fixtures or mounted in recessed pockets. The absence of a pre‑fitted thread simplifies customisation for specific applications and reduces the need to adapt standard fastenings. For bespoke assembly needs, secure bonding, countersinking or clamping arrangements can be chosen according to the fixture design; technical advice is available for selecting the most appropriate mounting method. Robust choice for repeated, low‑maintenance use Manufactured for dependable everyday use, the unit is engineered to deliver stable magnetic retention with minimal upkeep. The hard ferrite composition ensures long service life under standard workshop handling, while the clearly stated holding force gives planners a verifiable basis for fixture design. This combination of documented performance and simple mechanics makes the magnet an efficient choice for repetitive clamping tasks in production or repair settings. For compact, reliable magnetic clamping from TECWERK, contact Metav Werkzeuge for procurement support or tailored technical advice — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000832236NW SKU: 4000832236NW UID: 4000832236NW Dimensions / Performance Diameter: 40 mm Height: 8 mm Holding force: 125 N Recommended operating temperature: up to 100 °C Maximum temperature: 200 °C Packaging unit: 10 Materials / Design Material: hard ferrite Design: without threaded bush Product type: magnetic flat gripper Manufacturer brand: TECWERK FAQ What is the nominal holding force of this magnetic gripper? The magnetic flat gripper provides a holding force of 125 N, suitable for light clamping and fixturing tasks where this retention level is sufficient. Can the gripper be used at elevated temperatures? Yes, the unit has a recommended operating temperature of up to 100 °C and a maximum exposure rating of 200 °C for short periods. How is the gripper mounted without a threaded bush? The threadless base allows recessed or bonded mounting in custom fixtures; the design supports flush installation in jigs for a low overall profile. What material is the magnet made from and what are the benefits? Constructed from hard ferrite, the magnet offers stable magnetic properties, good corrosion resistance and suitability for routine workshop conditions. Is this product suitable for precision assembly jigs? Its compact 40 mm diameter and reliable holding force make it appropriate for many precision jigs where moderate retention and minimal bulk are needed. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
40mm Magnetic Flat Gripper With Threaded Bush Holding Force 125N, Up To 200°C - TECWERK
Take advantage of a compact, high-temperature-capable magnetic mounting with reliable 125 N holding force and a secure M5 threaded sleeve; order the flat magnetic holder directly via Metav Werkzeuge or consult our specialists for application advice. Flat magnetic holder D40×H18 mm by TECWERK — M5 thread sleeve, 125 N holding force Flat magnetic holder D40×H18 mm is a compact ferrite magnetic base designed for light clamping, positioning and fixturing tasks in workshops and assembly stations. 125 N holding force Hard ferrite construction M5 threaded sleeve Suitable to 200 °C short-term Reliable clamping where consistency matters The compact magnetic base delivers a measured 125 N of holding force, giving a dependable grip for small components and fixtures in routine workshop tasks. Constructed from hard ferrite, the unit maintains magnetic performance under regular industrial use and is specified with a recommended operating temperature up to 100 °C and a maximum of 200 °C for short-term exposure. These clear parameters support process planning and help avoid unexpected failures during thermal cycles. Space-saving design for flexible assembly With a diameter of 40 mm and a height of 18 mm, the magnetic holder fits into confined setups and can be mounted close to tooling or sensors without obstructing access. The integrated M5 thread sleeve permits secure fixing to threaded studs or adaptor plates, enabling repeatable positioning and quick replacement. This small footprint makes the component suitable for modular jigs, test rigs and light-duty fixturing where precision and accessibility are required. Durable choice that reduces handling time The ferrite magnet core and metal sleeve are engineered for straightforward, low-maintenance use: the magnetic base resists demagnetisation in normal workshop conditions and the threaded connection ensures stable mechanical coupling. As a result, assembly cycles benefit from fewer adjustments and reduced handling, supporting efficient throughput. The design emphasises functional reliability rather than decorative finish, making it a pragmatic option for production and repair environments. Contact Metav Werkzeuge for tailored procurement or application advice (info@metav-werkzeuge.com · +49 2822 7131930); our consultants will confirm compatibility and supply options quickly Technical data Article number: 4000832246NW SKU: 4000832246NW Manufacturer: TECWERK Product type: Flat magnetic holder Facts Diameter: 40 mm Height: 18 mm Holding force: 125 N Thread: M5 Recommended operating temperature: up to 100 °C Maximum operating temperature: 200 °C (short-term) Packing unit: 1 Special features Hard ferrite construction With threaded sleeve Compact design for tight spaces Suitable for light clamping and positioning FAQ What is the maximum holding force of the magnetic holder? The magnetic holder provides a maximum holding force of 125 N, suitable for light fixtures and component positioning. Which thread is integrated in the holder and how is it used? An M5 threaded sleeve is integrated into the unit, enabling secure attachment to threaded studs, adaptor plates or custom fixtures. What materials is the magnetic base made from? The core material is hard ferrite, combined with a metal threaded sleeve to ensure mechanical fixing and magnetic stability. What temperature ranges can the holder withstand? Normal operation is recommended up to 100 °C, with a maximum short-term exposure capability of 200 °C as specified. Is this magnetic holder suitable for heavy-duty machining fixturing? This product is intended for light clamping and positioning tasks; its 125 N holding force is optimised for small components rather than heavy machining loads. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
40mm x 25mm x 25mm Horseshoe Magnet AlNiCo 500 90N Holding Force, Max Temp 450°C - TECWERK
Take advantage of AlNiCo 500 construction and a 90 N holding force combined with high-temperature capability for reliable, long-term clamping; order the horseshoe magnet directly via Metav Werkzeuge or contact our specialists for application advice. Horseshoe Magnet L40×B25×H25 – AlNiCo 500, 90 N holding force (TECWERK) The horseshoe magnet L40×B25×H25 is a compact magnetic clamp for workshop and light industrial fixtures, designed for secure holding where elevated temperature resistance is required Robust AlNiCo 500 construction 90 N holding force for secure fixing 5 mm bore for mounting Rated for 450 °C continuous use Consistent, predictable magnetic performance for demanding work The magnet delivers a defined 90 N holding force, making it suitable for repetitive clamping and simple fixturing tasks where reproducible retention is important. Constructed from AlNiCo 500, the alloy combines good magnetic stability with thermal resilience; this means the magnetic properties remain more consistent at elevated temperatures than many ferrite alternatives. The specification for 450 °C maximum service temperature highlights its suitability for assemblies that are exposed to heat during processing. Where process reliability and consistent clamping are priorities, this material choice reduces the risk of performance drift and supports predictable production cycles. Space-saving dimensions and straightforward mounting With compact external dimensions of 40 x 25 x 25 mm and a central 5 mm bore, the component is engineered for easy integration into jigs, tooling plates or bespoke fixtures. The horseshoe form concentrates the magnetic field between the poles, enabling effective contact on small contact areas without excessive bulk. The through-hole offers a simple mechanical fixing option that keeps the magnet securely positioned while allowing rapid installation or replacement. For workshops optimising bench layout or retrofitting existing devices, the size and mounting design permit flexible use in restricted spaces. Durable handling and compatibility with post-processing The magnet is designed with practical workshop workflows in mind: the material and construction tolerate elevated temperatures, and the specification notes a painting temperature of 200 °C, which allows for certain finishing steps without compromising magnetic integrity. Packaged as a single unit, the item suits one-to-one replacements or small-batch assembly tasks. Applications range from holding fixtures and positioning aids to light tool retention where a compact, heat-resistant magnetic solution is required. The combination of material choice and geometry supports repeatable performance over many cycles, contributing to reduced downtime and increased process reliability. For application guidance or to reserve the TECWERK horseshoe magnet L40×B25×H25, contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for precise technical assistance and supply information. Technical data Article number: 4000832262NW Manufacturer: TECWERK Product type: Horseshoe magnet Packaging unit: 1 Facts Dimensions: 40 x 25 x 25 mm Holding force: 90 N Bore diameter: 5 mm Max operating temperature: 450 °C Painting temperature: 200 °C Materials & features Material: AlNiCo 500 Shape: Horseshoe magnet High-temperature resistance Single-unit packaging FAQ What maximum temperature can the magnet withstand without loss of function? The magnet is specified for a maximum operating temperature of 450 °C; the TECWERK horseshoe magnet L40×B25×H25 has been produced in AlNiCo 500 to provide thermal stability at elevated temperatures. What mounting options are available for this magnet? Mounting is via the central 5 mm bore, which permits secure mechanical fixing in jigs or fixtures while maintaining the magnet’s compact footprint. Which applications are best suited to this type of magnet? Typical uses include simple clamping, positioning aids and light fixturing in workshops and production cells where compact size and thermal resistance are required. Is the product delivered as a single item or in sets? The item is supplied as a single unit (packaging unit 1); refer to article number 4000832262NW for ordering. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
45mm Horseshoe Magnet With 118N Holding Force, AlNiCo 500 Coating - TECWERK
Take advantage of a compact, high‑temperature AlNiCo 500 solution with a reliable 118 N holding force and a 5 mm mounting bore for fixed workshop fixtures; the combination of thermal resilience and precise dimensions supports consistent production workflows. Order the horseshoe magnet directly via Metav Werkzeuge or ask our consultants if needed. Horseshoe Magnet L45 x B30 x H30 mm – AlNiCo 500, 118 N holding force (TECWERK) The Horseshoe Magnet L45 x B30 x H30 mm is a compact AlNiCo retaining magnet designed for high‑temperature fixtures and secure holding tasks in workshops and production cells. AlNiCo 500 for excellent thermal stability Holding force 118 N for secure retention Compact 45 x 30 x 30 mm with 5 mm bore Consistent magnetic retention for elevated temperatures The compact U‑shaped design provides a predictable holding force of 118 N, making it suitable for repeatable positioning and short‑term retention of small components. Manufactured from AlNiCo 500, the magnet maintains magnetic performance at elevated temperatures — the specified maximum operating temperature of 450 °C ensures stability where standard ferrite magnets would demagnetise. This thermal resilience is particularly relevant for assembly jigs, brazing fixtures, or processes that expose fixtures to heat, enabling a reduction in rework and downtime through reliable clamping behaviour. Small footprint and practical mounting for fixtures With outer dimensions of 45 x 30 x 30 mm and an integrated 5 mm bore, the magnet fits into compact jigs and can be secured with standard fasteners for repeatable alignment. The hole facilitates straightforward mechanical fixing, while the compact geometry supports close‑quarter clamping without obstructing adjacent tooling. The magnet’s coating bake temperature of 200 °C indicates compatibility with common paint and coating processes, allowing it to withstand finishing steps without loss of surface integrity. Material choice and predictable lifecycle performance Constructed from AlNiCo 500, this horseshoe magnet combines good corrosion resistance and dimensional stability with sustained magnetic properties at high temperatures. The solid construction minimises deformation risks and provides a reliable magnetic anchor across numerous cycle operations. For applications requiring consistent magnetic behaviour under thermal stress, the material selection reduces the need for oversized clamps or redundant fixturing, supporting faster set‑ups and leaner workflows. For project advice on integrating the TECWERK horseshoe magnet into heat‑exposed fixtures or for assistance selecting the right AlNiCo solution, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 4000832263NW UID: 4000832263NW Label: Hufeisenmagnet L45xB30xH30mm sta.Haftkraft 118N Facts Material: AlNiCo 500 Dimensions: 45 x 30 x 30 mm Holding force (max): 118 N Bore diameter: 5 mm Max operating temperature: 450 °C Coating bake temperature: 200 °C Special features Product type: Horseshoe magnet Brand: TECWERK Packing unit: 1 FAQ What maximum temperature can the magnet withstand? The magnet is specified for a maximum operating temperature of 450 °C, thanks to its AlNiCo 500 composition. How strong is the holding capacity in practical terms? The 118 N holding force provides secure retention for small parts and fixtures in typical workshop applications. Is the magnet ready for mechanical fastening? Yes, the integrated 5 mm bore permits mechanical attachment to jigs or mounting plates for repeatable positioning. Can the magnet tolerate common coating processes? The listed coating bake temperature of 200 °C indicates suitability for many paint and lacquer cycles without surface damage. For which tasks is this horseshoe magnet most appropriate? The magnet is intended for heat‑exposed fixtures, positioning aids and small clamping duties where a compact, thermally stable magnetic solution is required. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
57.2mm Horseshoe Magnet With 235N Holding Force, 7.9mm Holes - TECWERK
Take advantage of robust clamping and high-temperature stability combined with straightforward mounting for reliable jig and fixture work. The combination of AlNiCo 500 metallurgy and a 235 N holding force ensures repeatable positioning, while two 7.9 mm drilled holes permit secure attachment; order via Metav Werkzeuge or consult our specialists for application guidance. Horseshoe Magnet L57.2×B44.5×H34.9 mm – AlNiCo 500, 235 N The Horseshoe Magnet L57.2×B44.5×H34.9 mm is a compact industrial horseshoe magnet designed for secure fixturing and high-temperature environments in metalworking and assembly stations. AlNiCo 500 alloy for temperature stability Holding force 235 N for reliable clamping Two 7.9 mm drilled holes for secure mounting Consistent clamping reduces rejects and downtime The horseshoe design delivers a concentrated magnetic field that translates into a predictable holding force. With a rated 235 N, this magnet provides the mechanical stability needed for light to medium clamping tasks where repeatability matters. The AlNiCo 500 alloy maintains magnetic properties at elevated temperatures better than many ferrite magnets, so processes that produce heat benefit from fewer magnetic shifts. This results in fewer misplaced parts, less need for rework and improved process consistency—advantages that directly affect throughput and quality assurance. Built for elevated temperatures and production processes Rated for a maximum operating temperature of 450 °C, the magnet is suitable for applications where heat is present, such as near brazing, soldering or thermal treatment operations. The specified lacquering temperature of 200 °C relates to finishing and protective coatings applied during manufacturing; it indicates compatibility with common paint and lacquer processes. These thermal characteristics make the magnet a practical choice where thermal resilience is required, while still delivering dependable magnetic performance during normal production cycles. Designed for secure integration into fixtures Two precisely drilled holes with a diameter of 7.9 mm give clear options for mechanical fastening and alignment. The presence of two mounting holes simplifies repeatable installation into jigs and small fixtures and reduces the risk of lateral movement under load. The hole spacing and orientation favour stable clamping arrangements, enabling straightforward retrofitting into existing tooling or the construction of small bespoke assemblies without elaborate modification. Low-maintenance material choice and safe handling advice The magnet’s AlNiCo 500 construction offers stable magnetic behaviour and a long service life when handled correctly. Avoid hard mechanical shocks and keep the magnet free from heavy metallic debris to preserve the magnetic faces. Routine visual inspection is sufficient for most users; if the lacquered surface shows wear after thermal cycles, re-coating at or below the stated 200 °C lacquering temperature will maintain the protective finish. These straightforward care steps support dependable performance over many cycles while keeping maintenance effort to a minimum. Contact Metav Werkzeuge for tailored technical advice on integrating the TECWERK horseshoe magnet into existing fixtures and to arrange availability or a procurement consultation via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number / SKU: 4000832264NW Label: Horseshoe magnet L57.2×B44.5×H34.9 mm Manufacturer: TECWERK Numbers / Core technical data Holding force: 235 N Dimensions: 57.2 x 44.5 x 34.9 mm Maximum operating temperature: 450 °C Lacquering temperature: 200 °C Number of drilled holes: 2 Drill hole diameter: 7.9 mm Packaging unit: 1 Special features / Versions Material: AlNiCo 500 Shape: Horseshoe magnet Mounting: two drilled holes for secure attachment Application focus: fixtures, jigs, high-temperature environments FAQ What is the maximum temperature at which the magnet retains its properties? The TECWERK horseshoe magnet is specified for a maximum operating temperature of 450 °C, which reflects the thermal resilience of the AlNiCo 500 alloy used in this horseshoe magnet (SKU 4000832264NW). How strong is the magnetic hold for everyday fixture tasks? Rated at 235 N, the holding force provides reliable clamping for light to medium assembly and machining operations, delivering repeatable positioning when integrated into jigs or small fixtures. Which fasteners do the mounting holes accept? The magnet features two drilled holes with a diameter of 7.9 mm, designed to accommodate common fastening elements close to that diameter for secure mechanical attachment in tooling assemblies. Can the magnet be used near welding or heat-treatment processes? Yes; thanks to the AlNiCo 500 material and the 450 °C operating limit, the magnet is suitable for environments where moderate heat is present, though local conditions and thermal cycles should be evaluated for each application. What maintenance is recommended to keep the magnet working reliably? Routine cleaning to remove metallic debris and avoiding severe mechanical shocks are recommended; if the lacquer shows wear after heat exposure, re-coating at the stated 200 °C lacquering temperature will help preserve the finish. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
60mm x25mm x25mm Adjustable Permanent Magnet Positioner 150N Holding Force, 450°C Max - TECWERK
Take advantage of the combination of compact dimensions, an adjustable holding force of 150 N and a high specified operating temperature to secure small components reliably in confined workspaces; order directly via Metav Werkzeuge or ask our consultants for further assistance. Permanent magnet positioner 60 x 25 x 25 mm (adjustable, 150 N) – TECWERK A compact permanent magnet positioner 60 x 25 x 25 mm designed for adjustable holding and repeatable positioning in light assembly, fixturing and fabrication tasks. Compact 60 x 25 x 25 mm design Adjustable holding force up to 150 N Max magnet operating temperature 450 °C 125 mm total length for improved reach Secure clamping in tight assembly spaces The small footprint and compact dimensions make this positioner well suited where bench space or access is restricted. The device provides an adjustable magnetic hold that is specified up to holding force 150 N, enabling a controlled balance between grip and repositioning. This means delicate parts can be held without excessive force while heavier small components remain fixed during machining or alignment. The mechanism is designed for straightforward integration into jigs and light fixtures, making setup times predictable and repeatable. Performance under elevated temperatures and finishing processes The unit is specified with a max temperature 450 °C for the magnet and a coating curing temperature 200 °C, which supports use in processes that involve elevated heat during surface treatments or localised thermal exposure. These figures indicate the positioner has been engineered for environments where thermal stability is required; the magnetic properties and the surface finish parameters are documented to help plan process windows. The device is manufactured by TECWERK, and the technical specifications allow engineering teams to assess suitability for applications involving heat and post-process painting or coating. Efficient workflow integration and handling With a 125 mm total length, the positioner provides additional reach for positioning without sacrificing control. The adjustable design promotes faster part swaps and reduces the need for multiple different fixtures. Supplied as a single unit packaging, it is ready for immediate deployment into prototyping benches, small-series production or repair workshops. Documentation and clear numeric specifications support procurement and inventory processes, while the compact, robust design minimises the maintenance overhead typically associated with mechanical fixturing. For reliable, small-scale clamping with clear technical specifications, request the TECWERK permanent magnet positioner from Metav Werkzeuge and consult our product specialists for integration advice. Technical data Article number: 4000832285NW Brand: TECWERK Product type: Permanent magnet positioner Packaging unit: 1 Facts Dimensions: 60 x 25 x 25 mm Total length: 125 mm Holding force, max: 150 N Max magnet operating temperature: 450 °C Coating curing temperature: 200 °C Special features Adjustable execution Compact design for tight spaces Suitable for light assembly and fixturing Single unit delivery FAQ What applications is this positioner suitable for? The TECWERK positioner is suitable for light assembly, small-scale fixturing and fabrication tasks where a compact, repeatable magnetic hold is required; its specifications support use in workshops and bench operations. How is the holding force adjusted? Adjustment is achieved via the built-in adjustable mechanism; the holding force can be set up to a maximum of 150 N on the 4000832285NW unit to match the workpiece and process requirements. Can the magnet withstand elevated temperatures during coating or welding? The magnet is specified for a maximum operating temperature of 450 °C and the coating curing temperature is 200 °C, allowing assessment for heat-exposed processes when planning production steps. What are the exact dimensions and reach of the unit? The device measures 60 x 25 x 25 mm with a total length of 125 mm, providing compact support with additional reach for positioning tasks. How is the product supplied? The permanent magnet positioner is delivered as a single unit (packaging unit 1), ready for immediate use in bench or small production setups. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
65mm Pot Magnet 43mm High With M12 Threaded Counterbore, Holding Force 400 N - TECWERK
Take advantage of a compact, high-temperature-capable magnetic fixing that combines reliable 400 N holding force with a compact 65 mm diameter for consistent fixture retention; order the part directly via Metav Werkzeuge or consult Metav’s specialists for application advice. Pot magnet D65 H43 with M12 threaded blind hole – 400 N holding force (TECWERK) The Pot magnet D65 H43 with M12 threaded blind hole is a compact magnetic clamping solution designed for secure holding of fixtures and components in workshop and industrial environments. High-temperature resistant up to 450 °C AlNiCo 500 alloy for stable magnetism 65 mm diameter with M12 threaded blind hole Secure clamping with measurable performance The pot magnet delivers a consistent holding force of 400 N, distributed from its 65 mm diameter contact face to ensure dependable bracing of small to medium components. The integrated M12 threaded blind hole enables direct mounting to fixturing plates or jigs without additional adapters, simplifying assembly and reducing downtime. For production layouts where repeatable positioning matters, this magnetic retainer supports secure fixture placement and predictable load capacity, helping maintain process stability and throughput. Stable magnetic properties under heat Constructed from AlNiCo 500, the magnet maintains magnetic stability at elevated temperatures, with a maximum operating temperature of 450 °C. The specified coating process is rated to 200 °C, which helps preserve surface condition during thermal exposure. For operations involving heat treatment or oven-based processes, the alloy choice ensures the magnetic field remains reliable where ferritic magnets would lose effectiveness; this translates into fewer fixture failures and more predictable handling during thermal cycles. Robust design for workshop endurance The execution with a threaded blind hole offers a low-profile fastening option that protects the internal magnet assembly while enabling strong mechanical fixation. The geometry and material selection aim to reduce maintenance needs and support repeated mounting cycles typical in clamping technology. Supplied as a single unit per package, the component integrates easily into existing tool racks and holds up under frequent repositioning, reducing the time required for setup and adjustment in routine production tasks. Versatile applications across clamping tasks As a compact pot magnet from the clamping technology category, this part is suited to fixture building, temporary holding during assembly, and jigs used in light machining or inspection setups. The combination of AlNiCo 500 and the blind-thread mounting makes it particularly appropriate where elevated temperatures or compact installation space are factors. For buyers seeking to centralise procurement and secure consistent quality, the component aligns with workshop-standard demands for durable, measurable magnetic retention. For high-temperature magnetic fixing from TECWERK, contact Metav Werkzeuge to arrange procurement or to request application guidance directly from Metav’s specialists Technical data Article number: 4000832279NW Product type: Pot magnet Manufacturer: TECWERK UID: 4000832279NW Core specifications Diameter: 65 mm Height: 43 mm Holding force: 400 N Thread: M12 Maximum operating temperature: 450 °C Coating temperature resistance: 200 °C Packaging unit: 1 Special features Material: AlNiCo 500 Execution: with threaded blind hole Compact pot magnet design Intended for clamping and fixture applications FAQ What is the maximum holding force of this pot magnet? The pot magnet provides a maximum holding force of 400 N, specified for the TECWERK pot magnet (SKU 4000832279NW). Can the magnet be used in high-temperature environments? Yes, the TECWERK pot magnet, made of AlNiCo 500, is rated for a maximum operating temperature of 450 °C; the applied coating withstands up to 200 °C. How is the magnet mounted to a fixture? Mounting is via the built-in M12 threaded blind hole, allowing direct attachment to plates or jig elements without additional adapters. Is the material specified for the magnet suitable for industrial use? The core material is AlNiCo 500, chosen for its stable magnetic properties at elevated temperatures and consistent performance in industrial clamping contexts. How many units are supplied per package? The product is supplied as a single unit per packaging unit. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
77mm Plate Lifting Magnet With Leather Strap 150N Holding Force - TECWERK
Take advantage of the compact design and reliable retention of this lifting magnet to speed handling of small ferrous plates while maintaining safe grip through the supplied leather strap; order directly via Metav Werkzeuge or contact their consultants for application advice. Plate hand lifting magnet L77 x W37 x H14.5 mm with leather strap, 0.15 kN (TECWERK) Plate hand lifting magnet L77 x W37 x H14.5 mm with leather strap, 0.15 kN is a compact manual lifting aid for handling small ferrous sheets and components in workshop environments Compact dimensions 77 x 37 x 14.5 mm Leather strap for secure handling Holding force up to 150 N Suitable for sheet thickness from 2 mm Faster handling of small ferrous parts with predictable retention The compact lifting magnet delivers a consistent holding force that simplifies short-distance handling and positioning tasks. With external dimensions of 77 x 37 x 14.5 mm, the unit fits into confined work areas and on small benches where larger devices would be impractical. The specified maximum holding force of 150 N (0.15 kN) provides a clear, quantifiable performance figure that supports planning of manual handling processes and reduces handling time in repetitive tasks. By stating the retention value explicitly for thin material conditions, the specification enables pragmatic selection and integration into existing workflows. Secure grip and safer handling thanks to the leather strap Equipped with a leather strap, the tool offers improved manual control during lifting and transfer operations; the strap reduces the risk of slippage and allows a steady grip when manoeuvring small plates. The combination of a dedicated strap and compact geometry reduces hand fatigue during repeated cycles and supports safer, more controlled handling in assembly and maintenance applications. Where consistency matters, the visible mechanical retention figure and the strap together help ensure repeatable results when placing or removing components. Clear material suitability and application guidance Technical notes attached to the product indicate a suitable sheet thickness from 2 mm, while the stated retention data refers to conditions at 1 mm for reference. This distinction aids selection: the tool is intended for relatively thin ferrous plates but performs reliably once minimum thickness is observed. The transparent specification supports risk-aware use in light fabrication, repairs and small-part logistics, where predictable magnetic grip is needed rather than heavy lifting capacity. Compact design that supports workshop efficiency The small footprint of the device makes it particularly useful where space is limited or where multiple items must be handled in close proximity. The design reduces obstruction on workbenches and allows rapid placement and retrieval of parts without complex handling fixtures. As a straightforward manual aid, the magnet contributes to smoother workflows and faster cycle times in repetitive tasks, delivering a measurable productivity benefit for small-batch or shop-floor operations. Contact Metav Werkzeuge for tailored advice on application suitability and supply; call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss this TECWERK lifting magnet and delivery from Emmerich Technical data Article number: 4000832301NW Product type: Plate hand lifting magnet Brand: TECWERK Execution: with leather strap Packing unit: 1 Core data Dimensions: 77 x 37 x 14.5 mm Total height: 14.5 mm Maximum holding force: 150 N Specified holding force reference: at 1 mm sheet thickness Suitable sheet thickness: from 2 mm Special features Leather strap included Compact form factor for confined spaces Manual, non-powered operation FAQ What is the maximum holding force of this lifting magnet? The TECWERK plate hand lifting magnet has a maximum holding force of 150 N (0.15 kN) as specified for reference conditions. Which sheet thicknesses are suitable for use? The unit is designed for sheet thicknesses from 2 mm, with the manufacturer providing retention data referenced at 1 mm for comparative purposes. Is a leather strap included and how does it help? Yes, the device is supplied with a leather strap, which improves grip and handling safety when moving or positioning small ferrous plates. Can the magnet be used for heavy lifting tasks? This compact hand-held magnet is intended for light handling and positioning; the 150 N rating defines its practical limit and is not suitable for heavy lifting applications. What is the SKU for ordering or reference? Reference SKU: 4000832301NW for procurement and technical enquiries. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
8mm Magnet Rod Gripper Smooth, 4N Holding Force, AlNiCo 500 - TECWERK
Compact magnetic handling and high-temperature resilience combine in this compact unit: reliable 4 N holding force, AlNiCo 500 construction and a smooth finish enable secure part handling in demanding production settings; order directly via Metav Werkzeuge or consult our specialists for integration advice. Magnet rod gripper D8×H12 mm — smooth finish, 4 N holding force (TECWERK) A Magnet rod gripper D8×H12 mm designed for precise part pick-up and positioning in assembly, inspection and light automation tasks. AlNiCo 500 magnetic alloy construction High holding force: 4 N Compact D8×H12 mm smooth design Operates up to 450 °C with h6 tolerance Secure grip for delicate handling and repeatable pick-up The compact magnetic gripper delivers a 4 N holding force while preserving component surfaces thanks to its smooth finish. Constructed from AlNiCo 500, the alloy combines stable magnetic properties with resistance to demagnetisation at elevated temperatures, which translates into predictable performance across production cycles. The moderate holding capacity is ideal for small fixtures, rotating inspection stations and sensitive parts where over‑clamping would risk deformation. By converting raw magnetic parameters into practical outcomes, the unit supports consistent pick-and-place tasks with minimal setup time and reduced part damage. Built for heat and tolerance-critical processes Designed to tolerate temperatures up to 450 °C, the gripper is suitable for heat-treatment, brazing or processes near ovens where standard magnets would lose effectiveness. The supplied specification includes a h6 tolerance and a secondary dimension 3 mm for the interface, ensuring reproducible fits into housings or dedicated mounting sleeves. Explaining the terms: h6 denotes a tight shaft-to-bore fit class that helps preserve concentricity, and the declared operating temperature indicates retained magnetic performance rather than mere thermal resistance. These attributes make the device a reliable choice when thermal cycles and dimensional precision are combined requirements. Space-saving design for straightforward integration With outside dimensions D8×H12 mm and a smooth execution, the component is optimised for compact assemblies and retrofit into existing grippers or end‑of‑arm toolings. The minimal footprint reduces interference in dense layouts and simplifies collision avoidance in automated cells. The polished surface minimises friction and particulation, aiding maintenance in cleaner environments, while the magnetic alloy construction reduces the need for mechanical clamps on small parts. As a small, ready-to-install magnetic element, it supports faster machine cycles and lower tooling complexity without compromising positional repeatability. Contact Metav Werkzeuge for tailored supply and technical advice on TECWERK magnetic rod grippers; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 4000832251NW Product: Magnet rod gripper Brand: TECWERK Material: AlNiCo 500 Finish: smooth Core data Diameter: 8 mm Height: 12 mm Holding force (max): 4 N Operating temperature: up to 450 °C Tolerance class: h6 Dimension h: 3 mm Packaging unit: 1 Special features Compact D8×H12 mm design Smooth execution for minimal marking Suitable for high-temperature applications up to 450 °C Repeatable magnetic performance due to AlNiCo 500 FAQ What is the maximum holding capacity of this magnetic element? The maximum holding capacity is 4 N for the Magnet rod gripper D8×H12 mm, suitable for light part handling and positioning tasks. Can the gripper be used in high-temperature environments? Yes, the TECWERK magnetic rod gripper maintains performance up to 450 °C, making it appropriate for processes with elevated temperatures. What does the h6 tolerance mean for installation? A h6 tolerance indicates a close fit for the interface dimension; the gripper’s specified 3 mm dimension h and h6 class enable precise, reproducible mounting in housings or sleeves. Is the surface finish suitable for fragile components? The smooth execution reduces surface abrasion and particulation, so the device is well suited for handling delicate parts where marking must be minimised. Which alloy is used and why is it relevant? The gripper is made from AlNiCo 500, an alloy known for stable magnetic properties at higher temperatures and resistance to demagnetisation, which supports consistent handling performance. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
90mm x 40mm x 40mm Adjustable Permanent Magnet Positioner 250N Holding Force, Max Temp 450°C - TECWERK
Take advantage of the compact dimensions, adjustable alignment and 250 N holding force to secure reliable fixturing in heat-exposed production steps; order via Metav Werkzeuge or consult the technical team for application advice. TECWERK Adjustable permanent magnet positioner, 90 x 40 x 40 mm – 250 N holding force The TECWERK adjustable permanent magnet positioner for secure orientation and positioning in workshop and light industrial fixturing applications. Adjustable orientation for versatile clamping Compact 90 x 40 x 40 mm footprint Holding force 250 N for stable fixturing Tolerates magnet temperatures up to 450 °C Secure fixturing under heat and load The device delivers a holding force of 250 N, ensuring robust retention during light machining and assembly tasks where steady clamping is essential. The maximum magnet operating temperature of 450 °C means the unit maintains magnetic performance in many elevated-temperature processes; the specified lacquer curing temperature of 200 °C further clarifies suitability for environments where painted components or cured coatings are involved. This combination of thermal tolerance and predictable clamping force supports consistent throughput with fewer repositioning operations. Fast alignment with a compact footprint With outer dimensions 90 x 40 x 40 mm and a total length of 190 mm, the positioner occupies minimal bench or fixture space while still offering precise orientation. The adjustable execution allows small angular or positional corrections without swapping tools, reducing setup time and improving cycle efficiency. For workshops needing tight layouts or rapid changeovers, the compact form factor and adjustability translates into measurable time savings and fewer fixture variants. Practical design for workshop reliability Built as a pragmatic fixturing aid, the unit combines a simple mechanical adjustment with magnetic clamping that avoids extra bolts or complex jigs. The TECWERK construction provides repeatable positioning and easy integration into existing fixtures. Supplied as a single unit (packaging unit: 1), the component is suited for replacement or staged use across multiple workstations, supporting a streamlined inventory. The clear technical parameters permit straightforward planning for process engineers and workshop planners seeking dependable magnetic positioning. For an application match or to arrange supply from Metav Werkzeuge, request product advice on the TECWERK adjustable permanent magnet positioner 4000832286NW and discuss delivery from Emmerich. Technical data Article number: 4000832286NW Description: Adjustable permanent magnet positioner, 90 x 40 x 40 mm, holding force 250 N Facts Dimensions: 90 x 40 x 40 mm Total length: 190 mm Holding force: 250 N Maximum magnet operating temperature: 450 °C Lacquer curing temperature: 200 °C Packaging unit: 1 Special features Execution: adjustable Product type: Permanent magnet positioner Brand: TECWERK SKU: 4000832286NW FAQ What holding capacity does the positioner provide? The unit provides a holding force of 250 N, specified for stable fixturing and repeatable magnetic clamping. Can the positioner be used in applications with elevated temperatures? Yes. The positioner’s magnet is rated up to 450 °C, and the lacquer curing temperature is listed as 200 °C, indicating suitability for many high-temperature processes. How compact is the device for integration into fixtures? The footprint is 90 x 40 x 40 mm with a total length of 190 mm, which allows easy integration into tight fixture layouts. Is the orientation adjustable during setup? The execution is adjustable, enabling fine alignment without replacing the unit, which reduces setup time and increases flexibility. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com