150mm Shank Milling Cutter for RDMT 1003 Indexable Inserts, 20mm Shank Diameter - Teknik Makina

Take advantage of a compact holder that pairs precise insert seating with a 20 mm shank and 60 mm cutting length for efficient milling; available directly via Metav Werkzeuge for fast supply and expert consultation.

Shank cutter R200TM by Teknik Makina — 20 mm shank, for RDMT 1003 indexable inserts

The shank cutter R200TM is designed as a reliable insert holder for light to medium milling tasks that use RDMT 1003 indexable inserts, offering a compact overall length and standard fastenings for efficient workshop handling

• 20 mm shank diameter for secure clamping
• Compatible with RDMT 1003 indexable inserts
• 60 mm cutting length for deeper engagement
• Two cutting edges for balanced cutting action

Accurate seating for indexed inserts reduces setup variance

The holder is engineered for repeatable insert location, meaning each tool change preserves alignment and runout within tight limits. By using the established RDMT 1003 insert form, toolrooms benefit from fast reindexing and fewer clamping adjustments. The resulting advantage is a consistent surface finish and predictable tool life, which supports tighter process control and reduced scrap rates without adding inventory complexity.

Compact geometry that boosts cutting efficiency and stability

With a 20 mm shank and a 60 mm cutting length, this tool body provides a favourable ratio between reach and rigidity. The combination of a compact profile and two cutting edges helps to lower vibration and improve chip evacuation compared with longer, slender holders. For manufacturers seeking predictable cycle times, this geometry means higher effective cutting depths per pass and improved tool life through reduced deflection.

Standardised fastening for quick insert changes and low downtime

Serviceability is simplified by the use of a M3.5 locking screw and a M3.5x8.5 Torx screw, which require a T15 Torx key for secure clamping. The standard screw sizes allow workshop technicians to swap inserts rapidly with commonly available tools, shortening machine idle time. The holder’s 150 mm overall length and modest mass make it straightforward to handle during set-up, while the measured 0.336 kg mass contributes to predictable balancing behaviour in many spindle configurations.

Contact Metav Werkzeuge for tailored technical advice and to request the R200TM shank cutter for your indexable-insert milling requirements — fast supply from Emmerich and support from experienced precision specialists

Technical data

• Article number: R200TM
• Manufacturer: Teknik Makina
• SKU: R200TM

Facts

• Shank diameter: 20 mm
• Cutting length: 60 mm
• Overall length: 150 mm
• Diameter: 20 mm
• Cutting edges: 2
• Weight: 0.336 kg

Special features

• Compatible with RDMT 1003 indexable inserts
• Locking screw: M3,5
• Torx screw: M3,5x8,5
• Required Torx key size: T15

FAQ

Which inserts are compatible with this holder?
The R200TM shank cutter is compatible with RDMT 1003 indexable inserts, allowing use of that standard insert geometry for a wide range of finishing and light roughing tasks.

How many cutting edges does the tool provide?
The cutter body is designed for two cutting edges, delivering a balanced cutting action and improved stability during operation.

What are the key dimensions to check before ordering?
Key measures are a 20 mm shank diameter, 60 mm cutting length and 150 mm overall length; the tool weight is 0.336 kg.

Which fastening parts and tool sizes are required for insert changes?
Insert clamping uses a M3.5 locking screw and a M3.5x8.5 Torx screw; a T15 Torx key is required for secure tightening.

Is this holder suitable for compact machine spindles?
The compact profile and 20 mm shank make the R200TM well suited to setups where rigidity and a small holder envelope are required, while standard fastening sizes aid quick serviceability

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com