25mm Shank End Mill for LNMX 0603 Indexable Inserts, 4 Cutting Edges - Teknik Makina

Take advantage of the combination of secure clamping, compatibility with LNMX 0603 indexable inserts and a rigid Ø25 mm shank for uninterrupted milling performance — order the Shaft cutter S286TM directly via Metav Werkzeuge or ask our consultants if needed

Shaft cutter S286TM – indexable milling cutter, Ø25 mm, 4 cutting edges | Teknik Makina

The Shaft cutter S286TM is an indexable milling tool engineered for use with LNMX 0603 inserts, designed for stable face and slot milling in production and workshop environments

• Ø25 mm cutting diameter
• Compatible with LNMX 0603 inserts Korloy
• Four cutting edges for stable milling
• Shank Ø25 mm, overall length 140 mm

Consistent milling performance that reduces downtime

As an indexable milling cutter, this tool is built to deliver consistent cutting cycles while keeping maintenance intervals short. Compatibility with LNMX 0603 inserts means changeovers are fast and predictable; worn edges are replaced rather than the entire tool, lowering tooling expenditure and minimising machine downtime. The compatibility with Korloy insert geometries ensures access to a broad range of grades and chipbreakers, allowing process optimisation for different operational demands without altering the cutter body or clamping arrangement.

Rigidity and balance for accurate finishes

Rigidity is provided by a substantial Ø25 mm shank and a measured overall length of 140 mm, supplying the necessary stiffness for repeatable results across batch runs. The cutter features four cutting edges, which balance material removal rate and surface quality: fewer vibrations, improved tool life for the inserts, and a more consistent component finish. Reduced runout and even load distribution from the robust shank geometry contribute directly to tighter tolerances and lower scrap rates in serial production.

Quick, secure insert clamping for operational efficiency

Insert changes are secured via an M3x7 Torx screw and driven with a T8 key, allowing straightforward, toolroom-friendly replacement of indexable inserts. The clamping arrangement is engineered to ensure a firm seat for each LNMX 0603 plate, promoting repeatable seating and stable cutting forces. Faster insert swaps and reliable torque specification translate into less machine idle time and simplified workshop routines, particularly in multi-shift or mixed-production environments.

Wide applicability with standardised insert systems

Designed around the widely used LNMX 0603 insert format, the cutter is suitable for numerous milling tasks where an indexable solution is preferred over solid-end alternatives. The modular approach—cutter body plus standardised inserts—supports quick adaptation to changing job requirements by selecting the appropriate Korloy insert grade for a given material or surface quality target. The S286TM from Teknik Makina therefore provides a practical middle ground between flexibility and process stability for general milling operations

Discuss application suitability with Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 and arrange supply of the S286TM from Teknik Makina through our Emmerich hub

Technical Data

• Article number: S286TM
• Brand / Manufacturer: Teknik Makina
• SKU: S286TM
• ECLASS: 21180806
• ETIM: EC011860

Facts

• Diameter: 25 mm
• Shank diameter (aufnahme): 25 mm
• Overall length: 140 mm
• Cutting edges: 4

Special features

• For LNMX 0603 indexable inserts
• Compatible with Korloy inserts
• Torx screw M3x7, Torx key T8
• Indexable milling cutter design

FAQ

What insert format does this cutter accept?
The cutter accepts LNMX 0603 indexable inserts; the body is configured for that insert geometry to ensure correct seating and chip formation.

Which insert manufacturers are compatible?
This tool is compatible with Korloy inserts and with other suppliers following the LNMX 0603 standard; selection of grade depends on the workpiece material and cutting strategy.

What are the shank and overall dimensions?
The shank diameter is 25 mm and the overall length measures 140 mm, dimensions that favour stiffness and stability in typical milling setups.

How are inserts secured to the cutter?
Inserts are clamped with an M3x7 Torx screw and tightened using a T8 key, ensuring secure and repeatable clamping for reliable machining.

Is the S286TM suitable for high-production environments?
Yes, the modular indexable design of the S286TM by Teknik Makina suits repeated production cycles where quick insert changes and predictable performance are required.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com