40mm End Mill for BDMT 1704 Indexable Inserts With Internal Cooling, 120mm L - Teknik Makina

Take advantage of a rigid shank design and targeted cooling to maintain steady cutting performance across long production runs; the combination of a 40 mm cutting diameter, internal coolant and compatibility with BDMT 1704 indexable inserts keeps setup times low and productivity high. Order the cutter directly via Metav Werkzeuge or request tailored advice from the consultants in Emmerich.

Shank milling cutter S584-1TM — 40 mm diameter, internal coolant (Teknik Makina)

The Shank milling cutter S584-1TM is a robust insert cutter engineered for face and shoulder milling with BDMT 1704 indexable inserts, offering stable metal removal and short changeover times.

• 40 mm cutting diameter for stable milling
• Internal coolant for improved chip evacuation
• Compatible with BDMT 1704 inserts by Kyocera
• 32 mm shank with solid clamping stability

Reliable performance for demanding milling operations

The combination of a 40 mm cutting diameter and 4 cutting edges delivers a balance between material removal rate and surface quality. The 32 mm shank increases stiffness in the holder, reducing chatter and enabling higher feed rates with consistent results. For production environments this means fewer rejected parts and steadier cycle times; operators benefit from predictable tool behaviour and maintenance schedules, while planners gain measurable improvements in throughput and process stability.

Efficient cooling and chip control for extended tool life

Built-in internal coolant directs fluid to the cutting zone, flushing chips away from the inserts and reducing thermal stress on the cutting edges. This targeted cooling improves tool life and supports better surface finish on aluminium, steel and mixed-material workpieces when matched with suitable inserts. The internal coolant path also lowers the risk of chip re-cutting and abrasive wear, which contributes to longer intervals between indexings and lower total tooling consumption over a batch run.

Compatibility and straightforward maintenance for minimal downtime

Accepted inserts are BDMT 1704, and the cutter is compatible with inserts from Kyocera, enabling use of widely available grades for roughing and finishing. Fast insert changes are facilitated by the T15 Torx drive and M4x10 screws, which are standard in most maintenance toolkits. With an overall length of 120 mm and a cutting length of 40 mm, the tool offers a compact footprint while maintaining reach for shoulder operations. The modest mass of 0.791 kg simplifies handling and reduces toolholder imbalance when correctly clamped.

Practical workshop advantages and suitable applications

As an indexable shank cutter, the tool is suited to face milling, light shoulder milling and contouring operations where productivity and repeatability matter. The modular design reduces per-part tooling cost because only the inserts are replaced during wear cycles. For procurement and stock management, Metav’s European logistics base in Emmerich provides a near-market supply channel and quality filtering, which supports reliable reordering and consistent product specification across the workshop.

Contact Metav Werkzeuge for specification guidance on the Teknik Makina S584-1TM shank milling cutter and to confirm the ideal insert grade and coolant setup for specific applications; Metav’s consultants can advise on delivery from Emmerich and parts availability

Technical data

• Article number: S584-1TM
• Type: Shank milling cutter
• Brand: Teknik Makina
• Description: for BDMT 1704 Indexable Inserts
• Label: 40mm shank cutter BDMT 1704 L120mm with internal coolant

Facts

• Cutting diameter: 40 mm
• Overall length: 120 mm
• Shank diameter: 32 mm
• Cutting length (shank): 40 mm
• Number of cutting edges: 4
• Weight: 0.791 kg
• Torx key: T15
• Torx screw: M4x10
• eCl@ss: 21180806

Special features

• Internal coolant: true
• Compatible insert type: BDMT 1704
• Compatible insert manufacturer: Kyocera
• Product type: Shank milling cutter
• SKU: S584-1TM

FAQ

What inserts are suitable for this cutter?
The cutter accepts BDMT 1704 indexable inserts; compatible grades from Kyocera can be used for roughing or finishing depending on the workpiece material and cutting data.

Does the tool provide internal coolant?
Yes, internal coolant is integrated to deliver coolant directly to the cutting zone, improving chip evacuation and prolonging insert life.

What are the key dimensions for clamping and setup?
Clamping requires a 32 mm shank holder and the cutter has an overall length of 120 mm with a 40 mm cutting diameter, as stated in the technical data.

Which drive and screws are required for insert changes?
Insert retention uses a T15 Torx drive and M4x10 screws, enabling straightforward replacement with standard workshop tools.

Is the cutter suitable for fine finishing?
When equipped with an appropriate finishing grade insert, the cutter supports fine finishing operations and improved surface quality due to coolant-assisted cutting.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com