T15 Torx Key, 0.1kg - Teknik Makina

Take advantage of a compact, reliable fastening solution that combines a standard M4 thread with a 7 mm overall length for shallow assemblies, a 5.5 mm head diameter for consistent seat, and a Torx T15 drive for reduced cam‑out and predictable torque behaviour; order via Metav Werkzeuge or consult our specialists for batch supply and application advice Torx screw TC074TM (M4 x 7 mm, Torx T15) — Teknik Makina A Torx screw TC074TM designed for precise, repeatable fastening in general assembly and workshop applications where a T15 driver is used M4 thread for standard fastenings Short 7 mm length for confined assemblies Torx T15 drive reduces cam‑out risk 60° seat angle for reliable countersinking Secure fastening with consistent torque and fit This compact fastener provides a M4 thread combined with a 7 mm overall length and a 5.5 mm head diameter, delivering a predictable clamping result in small or shallow assemblies. The Torx T15 drive form reduces slippage and enables higher applied torque than comparable cross‑head types, which translates into fewer damaged heads and fewer reworks. For engineers specifying fixings in jigs, housings or light assemblies, the combination of thread dimension and short shank offers a neat balance between holding performance and minimal protrusion. Easier installation and clean countersinking for finishing The 60° seat angle ensures a clean, flush finish when paired with a matching countersink, improving load distribution and aesthetic appearance at the joint. Compatibility with a T15 key or driver bit makes assembly straightforward with standard hand or powered drivers, enabling faster cycle times on repetitive tasks. The fastener’s compact mass (listed as 0.1 kg) suits small parts production and reduces handling bulk for loose packs; the drive geometry also helps reduce operator fatigue during batch assembly by lowering the need for corrective actions. Supply reliability and why this choice supports workflow continuity Sourced from Teknik Makina, this Torx screw is supplied through Metav Werkzeuge’s logistics in Emmerich, combining manufacturer expertise with a European distribution filter that supports steady availability for industry and trade. Choosing this fastener helps simplify procurement for workshops and production lines that require standardised, repeatable fixings. Metav’s broad product range and established stock management reduce supplier multiplicity while offering traceable quality for repeat orders and project planning. For reliable procurement of Teknik Makina fasteners such as the TC074TM Torx screw, contact Metav Werkzeuge GmbH in Emmerich for batch availability and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: TC074TM Manufacturer: Teknik Makina EClass: 21189290 Facts Thread: M4 Diameter: 5.5 mm Overall length: 7 mm Seat angle: 60° Weight: 0.1 kg Special features Drive: Torx T15 (compatible with T15 key) Short shank for confined assemblies Countersunk seat geometry FAQ What thread size does this screw use? The Torx screw TC074TM features an M4 thread suitable for standard metric threaded holes and inserts. Which driver is required to install this fastener? Installation is performed with a T15 Torx driver or compatible T15 key; the TC074TM is optimised for Torx engagement to reduce cam‑out. Is the head suitable for countersunk installation? Yes, the fastener has a 60° seat angle intended for flush countersinking and even load distribution in finished assemblies. What are the length and head dimensions? The TC074TM has an overall length of 7 mm and a head diameter of 5.5 mm, designed for compact, low‑profile joints. Which applications suit this Torx screw? This fastener is appropriate for light mechanical assemblies, enclosures, fixtures and where a reliable, tamper‑resistant head engagement is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of secure fastening, a compact 12.5 mm length and standard M4 thread for reliable, space-saving assemblies; order the fastening solution directly via Metav Werkzeuge or consult the advisors for specification support. Torx screw TC076TM by Teknik Cutting Tools — M4 thread, 12.5 mm length The Torx screw is a compact fastening element designed for precision assemblies and confined fittings in mechanical and electronic applications Secure Torx drive for high torque transmission M4 metric thread for standard assembly fittings Compact 12.5 mm length for confined spaces 60° countersink angle for flush seating Precise fastening that prevents cam‑out and loosening The Torx drive design provides reliable engagement between driver and head, which reduces the risk of cam‑out under torque and improves assembly consistency. With an M4 thread and a 12.5 mm length, this fastener suits shallow joins and small fixtures where predictability matters. The combination of a narrow 5.5 mm diameter head and a 60° countersink angle enables neat, flush mounting in thin materials, improving both function and appearance while simplifying post‑assembly processes. Installation benefits and recommended tooling Installation is optimised for workshop efficiency: the fastener is intended for a T15 driver, ensuring correct bit fit and repeatable torque application. Using the correct driver reduces wear on both tool and fastener and contributes to faster cycle times on assembly lines or during repair work. The Torx geometry also supports higher torque transfer compared with slotted or Phillips heads, which is particularly useful for assemblies that demand secure clamping without over‑stress. Designed for compact and precise assemblies As a compact fastener, this component is well suited to instruments, enclosures and mechanical fixtures where space is limited and tolerances are tight. The controlled geometry of the head and thread supports consistent seating and reduces the need for rework. Lightweight and unobtrusive, the item helps maintain the design integrity of delicate housings and small machines while delivering the mechanical security expected in professional settings. Supply reliability and provenance assurance Sourced from Teknik Cutting Tools and offered via Metav Werkzeuge, the fastener benefits from a distribution channel that emphasises availability and quality assurance. Metav’s approach to making precision accessible for workshops ensures that such components are supported by clear stock information and fast order processing, helping to keep production lines moving and maintenance work on schedule. For technical queries, batch requirements or advice on using Teknik Cutting Tools Torx screws in specific assemblies, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by telephone at +49 2822 7131930 to arrange precise supply and specification support Technical data Article number: TC076TM Manufacturer: Teknik Makina ECLASS: 21189290 Weight: 0.1 kg Measurements Thread: M4 Diameter: 5.5 mm Total length: 12.5 mm Countersink angle: 60° Design & compatibility Drive: Torx Recommended driver: T15 driver Product type: Torx screw FAQ What driver is required to tighten this screw? The Torx screw TC076TM is designed for a T15 driver, which ensures correct engagement and consistent torque transfer during assembly. Will this screw sit flush in a countersunk hole? Yes, the TC076TM features a 60° countersink angle, allowing it to seat flush in appropriately prepared countersunk holes for a neat finish. What thread size does the fastener use? The TC076TM uses an M4 metric thread, making it compatible with standard M4 threaded components and inserts. Where is this fastener typically used? The Teknik Cutting Tools Torx screw TC076TM is intended for precision assemblies such as small enclosures, instrument housings and mechanical fixtures where compact, secure fastening is required. What are the head diameter and overall length of the screw? The TC076TM has a head diameter of 5.5 mm and a total length of 12.5 mm, designed for confined spaces and shallow material thicknesses. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact, reliable fastening with a secure Torx head and standard M4 metric thread — the small form factor (Ø 5.2 mm, length 11 mm) makes it well suited for precise assemblies and repeatable production processes. Order via Metav Werkzeuge or consult the technical team for batch supply and specification matching. Torx Screw TC079TM — M4 thread, 5.2 mm diameter | Teknik Makina Torx Screw TC079TM — a compact fastening solution for workshop and industrial assemblies, engineered for consistent drive engagement and standardised metric threading. Secure Torx head for positive drive M4 metric thread for standard assemblies 5.2 mm diameter for tight fit tolerances 11 mm overall length for compact applications Consistent drive performance for efficient assembly The Torx head profile delivers a reliable contact surface that reduces cam‑out and allows higher torque transmission compared with conventional recessed drives. For production environments where tool changeover and assembly speed matter, this profile supports repeatable torque application and lowers the risk of damaged fastener heads. Compatibility with a Torx key T15 ensures the component integrates seamlessly into standard driver sets and assembly fixtures. Metric thread stability to maintain joint integrity With an M4 metric thread, the fastener conforms to widely accepted metric systems used across mechanical assemblies. The combination of the M4 thread and the measured shank diameter of 5.2 mm provides predictable engagement and thread pitch behaviour, which simplifies torque settings and quality control. Using standardised components like this screw reduces the need for bespoke fasteners, aiding inventory management and procurement efficiency for production and maintenance teams. Small size, big application range The compact 11 mm overall length and a head angle of 45° (where applicable) make this screw particularly useful where space is restricted or where flush or near‑flush seating is required. Although the material is not specified in the data set, the dimensional accuracy and the Torx drive render the part suitable for precision fastening tasks in general workshop assemblies and light machinery. Batch procurement via an established distributor supports consistent supply and reduces lead‑time variability. Contact Metav Werkzeuge for quantity supply, specification matching or to discuss suitable driver options for the Teknik Makina Torx Screw TC079TM — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: TC079TM Brand: Teknik Makina ECLASS: 21189290 ** Dimensions & measurable data Diameter: 5.2 mm Thread: M4 Overall length: 11 mm Head angle: 45° Weight: 0.1 kg ** Design & special features Torx head profile Suitable for Torx key T15 Metric thread standard Compact length for tight assemblies ** FAQ What driver is required for this Torx screw? A Torx key T15 is specified as the compatible driver for this Torx screw; using the correct T15 driver ensures secure engagement and consistent torque transfer. Is the thread size compatible with DIN standard components? The fastener uses an M4 metric thread, which aligns with common metric component standards and simplifies integration with standard nuts and pre‑tapped holes. Can this screw be used where space is limited? Yes — the 11 mm overall length and compact diameter make it suitable for confined assemblies and applications requiring near‑flush fastening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The compact metric design combines precise M3.5 thread with a short 10 mm overall length for secure shim and U‑plate fastening; the standard compatibility with a hex key T15 streamlines assembly and reduces downtime. Order directly via Metav Werkzeuge or contact our consultants for compatibility advice. Screw for Shim TC040TM (M3.5, 10 mm) by Teknik Makina A screw for shim intended for secure fastening of U‑plates and shims in compact workshop and industrial fixtures. Compact M3.5 fastening element 10 mm overall length for tight assemblies Compatible with hex key T15 For U-plate and shim mounting Precise metric threading for dependable clamping The compact fastener is engineered with a M3.5 thread to ensure consistent engagement in metric fixtures. The standardised thread profile delivers predictable torque behaviour and repeatable clamping force, which supports reliable assembly processes and reduces the need for rework. As a small-format fixing element, it suits tight assemblies where controlled thread depth and clearance are essential, enabling secure retention of shims and U‑plates without overhanging components. This results in fewer stoppages and a more stable production flow. Quick installation with common workshop tools Installation is designed to be straightforward: the fixing accepts a hex key T15, allowing teams to work with familiar hand tools and torque drivers. The compatibility with common tools shortens setup time and simplifies maintenance tasks, contributing to faster changeovers in batch production or repair operations. Where repeatable tightening is required, the geometry facilitates even torque transfer, so fixtures remain stable under vibration and operational loads. This practical tool interface supports efficient workflows across workshops. Compact form for versatile fixture applications With an overall length of 10 mm and a nominal diameter of 8 mm, this fastener is tailored for confined installation spaces and low-profile clamping points. The low mass and modest dimensions make it suitable for assemblies where bulk must be avoided while maintaining secure anchorage. The component integrates easily into standard shim and U‑plate assemblies and aligns with common industrial part standards, providing interchangeability and ease of planning. For traceability and ordering, the item is listed under SKU TC040TM and originates from Teknik Makina, a recognised producer of precision fixing components. For specification checks, compatibility confirmation or to order the Teknik Makina TC040TM screw via Metav Werkzeuge, please contact Metav Werkzeuge and our technical advisors will assist promptly. Technical data Article number: TC040TM SKU: TC040TM Facts Diameter: 8 mm Thread: M3.5 Overall length: 10 mm Weight: 0.1 kg eClass: 21189290 Special features Suitable for shim / U‑plate mounting Compatible with hex key T15 Manufacturer: Teknik Cutting Tools FAQ What thread type does this fastener use? The screw uses an M3.5 thread, as specified for the Teknik Makina TC040TM fixing element, providing standard metric engagement for compatible fixtures. Is this part suitable for U‑plate and shim applications? Yes, the design is intended for shim and U‑plate mounting; the geometry and length support low‑profile clamping in such assemblies. Which tool is required for installation? Installation requires a hex key T15, allowing use of standard workshop hex keys or compatible torque drivers with the Teknik Makina TC040TM. How is the item identified for ordering? Order using SKU TC040TM; the part is supplied by Teknik Makina and stocked for straightforward procurement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact, space-saving fastening with a Torx drive and an M3.5 thread for reliable assemblies; combine secure engagement and precise dimensions for efficient production. Order this fastener directly via Metav Werkzeuge or consult our specialists for compatibility checks. Torx screw TC067TM — M3.5 thread, 8.5 mm length by Teknik Makina Torx screw TC067TM for compact mechanical assemblies, designed to deliver secure drive engagement and precise thread compatibility in confined spaces Torx drive for secure engagement Nominal diameter 5.3 mm Thread M3.5 standard Compact 8.5 mm total length Consistent torque transfer for dependable assembly results The Torx geometry is engineered to reduce cam‑out and provide improved torque transmission compared with slotted or Phillips drives. In practice this means assembly processes become more reliable and repeatable: a stable driver engagement reduces slip and wear on both tool and fastener; the combination of the Torx interface and the specified T15 matching key ensures a controlled transfer of force. For engineering teams this translates into fewer reworks and smoother production flow when fitting small components. Precision dimensions that save space and simplify design With a nominal diameter of 5.3 mm and a total length of 8.5 mm, the fastener is suitable for tight assemblies where clearance is limited. The external thread designated M3.5 conforms to standard metric sizing, enabling predictable mating with corresponding tapped holes or inserts. Designers benefit from the compact profile when specifying fastenings for enclosures, panels or small brackets, since predictable thread engagement and controlled head geometry support consistent clamping without excessive protrusion. Workshop efficiency and straightforward inventory management As a standardised metric fastener, the item streamlines procurement and tool selection across routine maintenance and assembly tasks. The relatively small mass (0.1 kg stated) aids logistics planning for storage and shipping bundles, while compatibility with the T15 driver reduces the number of specialised tools required on the workbench. Supplied under the Teknik Makina designation, the component is intended as a practical choice for small‑part assembly where standardisation and accessibility are priorities. Proven supply and service through a trusted partner Sourcing through Metav aligns the technical benefits of the fastener with dependable distribution and quality control. Metav’s role as a “quality filter” for the European market means buyers gain access to consistent stock, product verification and a broad range of workshop supplies alongside measurement and tooling solutions. This combination of a reliable feed of standard parts and technical consultancy supports long‑term operational stability in manufacturing and maintenance settings. For availability and order details of the Teknik Makina Torx screw TC067TM, contact Metav Werkzeuge in Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com for precise product information and stock status Technical Data Article number: TC067TM Manufacturer: Teknik Makina eCl@ss: 21189290 Core technical data Weight: 0.1 kg Diameter: 5.3 mm Thread: M3.5 Total length: 8.5 mm Head angle: 60° Features Drive type: Torx Suitable key: T15 Brand: Teknik Makina FAQ What driver fits this screw most effectively? The screw is designed for a Torx drive and is compatible with a T15 Torx key for optimal engagement. Which thread standard does the fastener use? This fastener uses an M3.5 metric thread suitable for corresponding tapped holes and standard inserts. What are the primary dimensions to consider during design? Key dimensions are a nominal diameter of 5.3 mm, a total length of 8.5 mm and a head angle of 60°, which help define clearance and engagement depth. Is this part a Teknik Makina product and what is the SKU? Yes — the item is listed under Teknik Makina and is supplied as TC067TM. For which kinds of assemblies is this fastener appropriate? The component is intended for compact mechanical assemblies and small fittings where a secure Torx drive and short overall length are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise drive engagement and predictable seating provided by the Torx screw TC068TM; its Torx T15 drive and M3.5 thread ensure secure fastening and consistent assembly results. Order the fastener directly via Metav Werkzeuge or consult the Metav advisors for technical clarification. Torx screw TC068TM — M3.5 × 11 mm Torx fastener by Teknik Makina The Torx screw TC068TM is a compact fastener for fine mechanical assemblies and light engineering work, designed for reliable torque transfer where controlled clamping and repeatable seating are essential. Torx T15 drive for secure engagement M3.5 thread for fine assemblies 11 mm length with 5.3 mm diameter 60° head angle for reliable seating Reliable torque transfer for precise assemblies The Torx T15 star profile delivers controlled torque transmission and minimises cam‑out risk, which helps maintain screw integrity and reduces the need for rework. Combined with the M3.5 thread and a nominal 11 mm length, this fastener provides predictable clamp force in small assemblies. The specified 5.3 mm diameter and 60° head angle support consistent seating in pre‑prepared holes or countersunk features, making the component suitable for repeatable production tasks where accuracy matters. Compatibility that keeps production moving Designed to operate with standard Torx tooling, the fastener supports efficient manual or semi‑automated fitting processes. The standardised drive and metric thread simplify tool selection and inventory management, reducing downtime between operations. With a listed unit weight of 0.1 kg, handling and storage planning can be integrated into workshop logistics. The dimensional clarity of this component aids quality assurance checks and helps maintain throughput in small‑part assembly lines. Procurement clarity and documentation for workshop use Clear identification by SKU and measurable specifications streamlines procurement and traceability: the item can be referenced directly in bills of materials and maintenance records. The compact geometry and defined head angle make it easy to specify for engineers and buyers when updating assembly drawings or ordering replacement parts. For organisations seeking reliable repeatability from a recognised supplier, this fastener fits standard workshop and light industrial requirements and is accompanied by the technical data needed for process documentation. Secure consistent assembly results with Teknik Makina fasteners — order TC068TM through Metav Werkzeuge for dependable supply and further specification support from Metav Werkzeuge in Emmerich (info@metav-werkzeuge.com, +49 2822 7131930) Technical Data SKU: TC068TM Product name: Torx screw TC068TM Manufacturer: Teknik Makina eClass: 21189290 Facts Thread: M3.5 Overall length: 11 mm Diameter: 5.3 mm Head angle: 60° Weight: 0.1 kg Special features Torx T15 drive compatibility Fine thread for small assemblies Compact 11 mm length Suitable for precision workshop use FAQ What torque tools are compatible with this fastener? The Torx screw TC068TM is compatible with standard Torx T15 drivers and bits designed for small assembly operations. Is the thread size standard metric? Yes, the fastener features an M3.5 metric thread suitable for fine threaded applications. Which applications are typical for this type of screw? This type of fastener is commonly used in light engineering, instrument assemblies and other small‑part mechanical joins where controlled clamping is required. How is the component identified when ordering? Order by SKU TC068TM and specify the Torx screw TC068TM with M3.5 × 11 mm dimensions for unambiguous procurement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a secure Torx connection and standard M4 threading for consistent assembly performance; the combination of a Torx head, a nominal 5.5 mm diameter and a defined 60° head geometry supports reliable torque transfer and repeatable fastening — order via Metav Werkzeuge or contact the consultants for specification advice. Torx screw TC073TM — M4 thread, 5.5 mm nominal diameter by Teknik Makina Torx screw TC073TM designed for secure mechanical fastening in industrial and workshop assemblies, suitable for standard metric fittings and driven with a Torx T15 tool Secure Torx head for high torque M4 metric thread for standard fittings 5.5 mm nominal diameter Requires Torx T15 driver High torque retention and reduced cam‑out for efficient assembly The Torx head geometry delivers superior torque transmission compared with slotted or Phillips profiles, which reduces the risk of cam‑out during tightening. Combined with the M4 thread, this fastener ensures consistent clamping force in light to medium duty assemblies; the specified 5.5 mm nominal diameter is matched to the thread form to provide stable engagement. The listed 60° head angle contributes to controlled seating where a countersunk finish is required, allowing a flush appearance and predictable load distribution. These characteristics translate directly into fewer rework cycles and faster cycle times on repetitive assembly tasks. Practical compatibility and workshop handling benefits The fastener is prepared for standard workshop tooling: a Torx T15 driver fits the head profile for rapid insertion and secure torque application. The item is compact and of low listed mass (0.1 kg), aiding handling and reducing shipping bulk when small quantities are required. Because the design focuses on mechanical reliability rather than decorative finishes, the component integrates well with maintenance procedures and retrofit operations where metric thread conformity and repeatable torque behaviour are priorities. Clear driver selection and standard threading simplify inventory management across production and service departments. Sourcing and application confidence for industrial users Produced by Teknik Makina, the component matches expectations for a basic, reliable threaded fastener for industrial use. The specification supports applications in jigs, fixtures, enclosure assemblies and general workshop repairs where a dependable metric fastener is required. Procuring through Metav places this component within a broader supply chain advantage: centralised access to precision tools and fasteners, steady stock levels and transparent order processing from Emmerich. The result is a practical balance of availability and specification conformity that helps to keep production lines and maintenance bays moving. For fast, reliable procurement of Teknik Makina fasteners such as the Torx screw TC073TM and personalised technical guidance, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt support and ordering assistance Technical data Article number: TC073TM Manufacturer: Teknik Makina ECLASS: 21189290 Core specifications Diameter: 5.5 mm Thread: M4 Overall length: 1 Weight: 0.1 kg Materials & features Head angle: 60° Driver compatibility: Torx T15 SKU: TC073TM FAQ What driver is required for this screw? The Torx screw TC073TM is specified for a Torx T15 driver to ensure correct engagement and torque transfer. What thread standard does the fastener use? This threaded fastener is supplied with an M4 metric thread suitable for standard metric mating threads. Is the head geometry suitable for flush mounting? Yes, the indicated 60° head angle supports countersunk seating for a flush finish in compatible components. Can this fastener be used in maintenance and retrofit work? The TC073TM by Teknik Makina is intended for general workshop and industrial applications where a reliable metric fastener and Torx drive are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Secure assemblies benefit from the combination of a Torx T15 drive and an M4 thread, together with a compact 11 mm overall length for space-conscious installations. For seamless procurement or specification advice, order via Metav Werkzeuge or consult our product specialists. Torx screw — M4 thread, Torx T15 drive (Teknik Makina) Torx screw engineered for reliable fastening in workshop and industrial applications, featuring an M4 metric thread and a Torx T15 drive for consistent torque transfer M4 metric thread for standard fittings 11 mm overall length for compact assemblies Torx T15 drive for secure torque transfer 7 mm head diameter for firm seating Consistent torque and reduced cam‑out for reliable joints The fastener is built around a Torx T15 drive to ensure controlled torque application and to reduce cam‑out compared with slotted or Phillips heads. This geometry transfers force more efficiently to the screw shank, lowering the risk of driver slippage and damage to mating components. The M4 thread offers compatibility with common metric inserts and tapped holes, enabling repeatable clamping forces in production or maintenance tasks while preserving thread integrity over multiple service cycles. Compact dimensions for tight assemblies and neat finishes With an 11 mm overall length and a 7 mm head diameter, this screw suits confined spaces where a secure connection must not intrude on surrounding components. The specified 60° angle contributes to predictable seating behaviour and consistent contact with mating surfaces, which helps maintain alignment in assemblies with shallow countersinks. The compact form factor supports neat, professional finishes in panels, enclosures and small assemblies without sacrificing holding strength. Workshop compatibility and supply stability for production use Designed for efficient workshop workflows, the screw accepts a Torx key T15 as the drive tool and integrates easily into assembly processes that favour Torx interfaces. The part is produced by Teknik Makina and listed under SKU TC075TM, making it straightforward to specify on procurement documents. Sourcing via an established distributor avoids supply interruptions: pairing robust component design with dependable logistics supports uninterrupted production and reduces rework risk. For tailored advice on integrating the Teknik Makina Torx screw TC075TM into production or maintenance routines, contact Metav Werkzeuge in Emmerich—technical specialists are available by email or phone to support specification and delivery. Technical data Article number: TC075TM Manufacturer: Teknik Makina EClass: 21189290 Drive type: Torx T15 Facts Weight: 0.1 kg Diameter: 7 mm Thread: M4 Length: 11 mm Head angle: 60° Special features Drive tool: Torx key T15 Compact head for tight spaces Metric thread for standard fittings Manufacturer SKU: TC075TM FAQ What drive tool is required for this screw? The Torx screw uses a Torx T15 drive; the supplied specification for TC075TM calls for a T15 Torx key for torque application. What are the thread and length specifications? This fastener is supplied with an M4 metric thread and an overall length of 11 mm; head diameter is 7 mm with a 60° head angle. Is this component suitable for compact assemblies? Yes, the combination of an 11 mm overall length and a 7 mm head diameter makes this screw suitable for confined spaces and shallow countersinks. Who manufactures this screw and how is it identified? The screw is manufactured by Teknik Makina and is identified as TC075TM in technical documentation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable fastening performance is achieved through the combination of a Torx drive and a metric M4 thread, delivering secure joints in confined assemblies; the compact 11 mm overall length and 6.7 mm diameter support space-saving designs. Order via Metav Werkzeuge or consult the technical team for application guidance. Torx Screw — M4 thread, 11 mm overall length (Teknik Makina) A Torx Screw engineered for reliable mechanical fastening in industrial and workshop settings, offering a compact profile and Torx-compatible drive for stable torque transmission. Torx head for high torque transfer Metric M4 thread for standard fastening Compact 11 mm length for tight spaces 60° seat angle for precise seating Secure joints with compact dimensions The compact profile combines a metric M4 thread with a modest overall length of 11 mm, making this fastener well suited to assemblies where space is limited. The modest 6.7 mm diameter maintains a low profile without compromising clamping force; when paired with a properly sized threaded hole or insert, the result is a consistent mechanical connection. The technical design supports repeatable installation in production or repair tasks and reduces the need for post-assembly rework. Reliable torque transfer and tool compatibility A Torx drive provides superior torque transmission compared with slotted or Phillips heads, reducing cam-out and wear on both the fastener and the tool. This component is compatible with a T15 Torx key, enabling efficient installation with power or hand tools commonly used in workshops. The 60° seating angle facilitates accurate countersinking where required, ensuring the fastener sits flush and distributes load evenly across the mating surface. Assembly efficiency and procurement confidence From a procurement perspective, the straightforward specification—M4 thread, 11 mm length, 6.7 mm diameter—simplifies component selection and inventory management. The item’s modest mass (0.1 kg) supports easy handling and predictable packaging. Specifiers and purchasing teams benefit from the clear technical parameters for CAD models, bill of materials and quality checks, while production staff gain a dependable, repeatable fastener for everyday applications. For workshop-grade fastening and bulk supply, trust Teknik Makina’s Torx screw and contact Metav Werkzeuge for procurement and technical clarification at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: TC078TM Manufacturer: Teknik Makina ECLASS: 21189290 Weight: 0.1 kg Dimensions & thread Diameter: 6.7 mm Thread: M4 Overall length: 11 mm Angle: 60° Design & compatibility Drive type: Torx Compatible key: T15 Torx key FAQ What driver is required for installation? This Torx screw (Teknik Makina, fastener, SKU TC078TM) is driven with a T15 Torx key or a compatible T15 Torx bit for power tools. What are the thread and external dimensions? The fastener has a metric M4 thread, an overall length of 11 mm and a diameter of 6.7 mm as specified for SKU TC078TM from Teknik Makina. How does the 60° angle affect seating? The 60° angle defines the seating geometry to allow a flush countersunk fit; when combined with appropriate matching countersink geometry, the screw distributes load evenly. Is this fastener suitable for compact assemblies? Yes, the short 11 mm overall length and modest 6.7 mm diameter make this Torx screw (Teknik Makina, SKU TC078TM) suitable for confined or low-profile assemblies. What advantages does a Torx drive provide over other head types? A Torx drive reduces cam-out and allows higher torque transfer with less tool wear, improving installation reliability for recurring production tasks such as those performed with SKU TC078TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact Torx screw that combines secure Torx T15 drive compatibility, a standard M4.5 thread and a countersink-friendly 60° head for consistently flush assemblies; order directly through Metav Werkzeuge or contact our consultants for specification support. Torx screw TC080TM — M4.5 × 11 mm, Torx T15 by Teknik Makina A Torx screw intended for standard workshop and assembly applications, offering an M4.5 thread and an 11 mm total length for reliable, repeatable fastening. Torx T15 drive compatible Thread M4.5 for standard fittings 11 mm total length 60° head angle for flush fastening Precise fastening for repeatable assembly results The compact fastener delivers mechanical reliability by combining a standard M4.5 thread with a short, controlled shank. The combination of a metric thread and a shallow overall length results in predictable clamping behaviour when used in pre-tapped holes or with matching threaded inserts. Matching the drive to a Torx T15 tool reduces cam‑out and torque loss during installation, contributing to consistent joint preload and fewer reworks. The specification supports process stability in small- to medium-scale assemblies where repeatability matters. Tool compatibility and installation efficiency The head geometry, given as a 60° angle, indicates suitability for countersunk or flush mounting where a low-profile finish is required. The Torx interface paired with a T15 driver enables efficient torque transfer and precise positioning, which speeds up automated and manual assembly steps alike. Reduced cam‑out extends driver bit life and lowers the incidence of damaged heads; the fastener’s dimensions (diameter 6.2 mm, thread M4.5, total length 11 mm) make it a practical choice for compact components and confined installation spaces. Workshop readiness and supply reliability Technical simplicity and conformity to familiar standards make this fastener straightforward to specify across procurement and production documents. The item’s listed mass (0.1 kg) is useful for logistics and inventory planning. Sourcing via a trusted partner helps maintain continuity of supply: Metav combines a broad product range with a quality filter at its Emmerich site, backed by long‑standing industry relationships and an established customer base of over 48,000 customers. For procurement planners and workshop managers, the combination of standard sizing and trusted distribution reduces administrative overhead and supports uninterrupted assembly operations. For availability checks, compatibility advice or to secure Teknik Makina stock through Metav Werkzeuge, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for prompt assistance Technical data Article number: TC080TM Designation: Torx screw Manufacturer: Teknik Makina eClass: 21189290 Facts Diameter: 6.2 mm Thread: M4.5 Total length: 11 mm Head angle: 60° Weight: 0.1 kg Special features Torx drive: T15 compatible Countersink geometry indicated Standard workshop fastener FAQ What driver fits this screw? The Torx screw TC080TM is compatible with a Torx T15 driver for optimal torque transfer and reduced cam‑out. Is the head suitable for a flush finish? Yes, the head angle of 60° on the TC080TM is intended for countersunk applications and provides a low‑profile finish when installed correctly. What are the core dimensions of the fastener? Diameter 6.2 mm, thread M4.5 and total length 11 mm are the primary dimensions of the TC080TM. Is this fastener suitable for automated assembly? The Torx interface (T15) and standard metric thread make the TC080TM well suited to both manual and automated assembly processes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of robust metric compatibility and a compact format to secure shims and U-plates with minimal assembly height; order directly via Metav Werkzeuge or consult our specialists for procurement and supply from Emmerich. Screw TC038TM – M4 thread, 10 mm overall length (Teknik Makina) A Screw TC038TM engineered for fastening shims and U-plates in compact assemblies within general workshop and clamping applications. M4 metric thread standard fitting 10 mm overall length for low-profile joints 7.3 mm nominal diameter for reliable seating Compatible with T15 hex key for installation Reliable metric fastening with proven compatibility The TC038TM is specified with an M4 metric thread and a 7.3 mm nominal diameter, which delivers a consistent fit with standard threaded holes and inserts. The use of a standard metric thread simplifies parts sourcing and replacement across toolrooms and production cells; this compatibility reduces downtime and streamlines inventory management. In practical terms, the defined geometry enables predictable clamp forces and repeatable assembly behaviour, which supports efficient process planning in small-series production and maintenance tasks. Low-profile design that reduces interference in assemblies With an overall length of 10 mm, this fastening element offers a compact design ideal for situations where protrusion must be minimised. The shorter length helps prevent collisions with neighbouring components and reduces lever arms that can induce bending moments under load. Combined with the nominal diameter, the profile ensures secure seating in shims and U-plate connections without excess material above the mating surface. Where space and clearance are at a premium, this configuration supports neater, safer mechanical joints. Straightforward installation and dependable performance Assembly is designed to be efficient: the screw integrates with a T15 hex key, enabling controlled torque application with commonly available tools. The specified tool interface supports consistent tightening and helps avoid cross-head damage or slippage during installation. At a measured mass of 0.1 kg, the component is easy to handle in manual and semi-automated workflows, while the clear specification facilitates purchasing and quality checks. Supplied by Teknik Makina and distributed via established supply channels, the part is suitable for workshops and stockrooms that prioritise traceable, standardised components. Contact Metav Werkzeuge for a tailored procurement proposal for the Teknik Cutting Tools TC038TM screw, including delivery options from our Emmerich stock and advice on matching fasteners to specific shim or U-plate assemblies Technical data Article number: TC038TM Manufacturer: Teknik Makina Facts Diameter: 7.3 mm Thread: M4 Overall length: 10 mm Weight: 0.1 kg eCl@ss: 21189290 Special features Application: for shim / U-plate fastening Compatible tool: T15 hex key Product type: metric screw FAQ What thread size does this screw use? The screw uses an M4 metric thread; the TC038TM by Teknik Makina is specified for standard M4 fittings. Is the screw suitable for securing shims or U-plates? Yes, the TC038TM is designed for fastening shims and U-plates and is listed with the application “for shim / U-plate”. Which installation tool is required for this fastener? Installation requires a T15 hex key, enabling controlled torque when fitting the TC038TM screw. What is the overall length and nominal diameter of the part? The part has an overall length of 10 mm and a nominal diameter of 7.3 mm, suitable for low-profile assemblies. Can this component be sourced through Metav Werkzeuge? The TC038TM screw from Teknik Makina is available via Metav Werkzeuge; procurement can be coordinated from the Emmerich stock. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the M4 thread and compact 5.8 mm diameter for secure clamping and straightforward installation; benefit from consistent toolholding in confined setups and consult Metav Werkzeuge for ordering or technical advice. Screw TC172TM for End Mill — M4 thread, 5.8 mm diameter (Teknik Makina) The Screw TC172TM is a compact clamping screw designed to secure end mills in tight tool-holder assemblies, offering a small footprint and simple hex-key assembly for reliable tool retention. M4 threaded clamping screw 5.8 mm outer diameter 9 mm total length Requires hex key T15 Reliable clamping that reduces runout and rework The central advantage of the fastener lies in its M4 thread, which provides repeatable axial force and stable retention during milling operations. Consistent clamping reduces micro-movement of the cutting tool, thereby lowering the risk of tool chatter and premature wear. This stability supports process reliability and helps maintain dimensional accuracy on workpieces, so fewer reworks are necessary and cycle-time consistency improves. Space-saving dimensions for compact tool stations With an outer diameter of 5.8 mm and a 9 mm total length, the component is optimised for setups where space is limited. The compact profile enables use in close-packed tool arrangements and multi-tool fixtures without interfering with adjacent holders or cutters. Such a small form factor supports flexible tooling layouts and can simplify retrofitting into existing spindles or adapters where clearance is critical. Simple assembly and workshop compatibility for faster changeovers Assembly requires a T15 hex key, a common size in workshop toolkits, which makes installation and removal quick and predictable. The lightweight construction (listed weight 0.1 kg) and standardised thread and drive type reduce the need for specialised tools and spare parts inventory. For maintenance planners and toolroom managers this translates into shorter tool-change times and lower operational friction in everyday machining routines. For purchasing and tailored technical guidance on Teknik Cutting Tools components such as the Screw TC172TM, contact Metav Werkzeuge — quick delivery and expert advice are available from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: TC172TM Designation: Screw for end mill Manufacturer: Teknik Makina ECLASS: 21189290 Facts Diameter: 5.8 mm Thread: M4 Total length: 9 mm Weight: 0.1 kg Special features Requires hex key T15 Intended for securing end mills Compact clamping geometry FAQ Is this screw suitable for standard end mills? The Screw TC172TM is designed specifically for securing end mills and is compatible with common tool-holder geometries where an M4 clamping screw is specified. Which tool is required to install the screw? Installation and removal are performed with a T15 hex key, a standard workshop tool compatible with this clamping screw. What are the key dimensions to check before ordering? Confirm the 5.8 mm diameter, M4 thread and 9 mm total length match the tool-holder or adapter specification; these are the critical dimensions for compatibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com