63mm Turning Tool Head 90° For LNGX 1307 Indexable Inserts M4x10 Torx T15, 22mm Shank, 45mm Overall Length - Teknik Makina

High-precision corner turning is achieved by combining a stable clamping concept with a compact profile and compatibility for standard indexable inserts; the combination of the 90° cutting angle, secure Torx M4x10 fixing and the compact Ø63 mm body supports consistent part geometry and reduced set-up time. Order the corner tool head directly via Metav Werkzeuge or consult our advisors for application-specific guidance.

Eckmesserkopf T492TM — Corner tool head, 90° cutting angle, Ø63 mm (Teknik Makina)

The Eckmesserkopf T492TM is a compact corner-turning head designed for use with LNGX 1307 indexable inserts in precision turning and profiling tasks on lathes and turning centres.

*Compact Ø63 mm body for tight toolposts *Compatible with LNGX 1307 indexable inserts *Secure Torx M4x10 fixing; T15 key interface *Precise 90° cutting angle; six cutting edges

Consistent geometry through a true 90° cutting angle

The rigid design centres on a 90° cutting angle that stabilises the cutting direction and reduces the need for corrective reworking. With six cutting edges, the head enables repeatable corner radii and predictable chip flow, which in turn supports consistent surface finish and dimensional control. For workshops that value first-pass accuracy, this configuration reduces inspection loops and shortens cycle time.

Fast, secure insert changes minimise downtime

The clamping system uses a Torx M4x10 screw and a T15 key interface for quick and reliable indexable insert replacement. Compatibility with LNGX 1307 inserts — widely available from Walter and other manufacturers — simplifies inventory management and allows rapid changeovers. The straightforward fastening procedure supports fast maintenance intervals and a low risk of incorrect seating.

Compact footprint with robust mounting and balance

A compact Ø63 mm head and an overall length of 45 mm combine with a 22 mm mounting diameter to fit small toolposts while retaining rigidity. At approximately 0.56 kg, the unit balances mass and stiffness for stable cutting under typical turning loads. This compact construction is advantageous for confined setups where tool clearance and unobstructed chip evacuation are essential.

Clear application scope and practical handling

Designed primarily for corner and profiling operations with indexable inserts, the head is suitable for standard turning cycles where insert interchangeability and positional accuracy are required. An indexable insert system means the cutting edge can be renewed without regrinding the tool, which lowers tooling cost per part while maintaining machining quality. For clarification on machine compatibility or specific machining strategies, Metav Werkzeuge provides application support and selection advice.

For application advice or a tailored quotation for the Teknik Makina Eckmesserkopf T492TM, contact Metav Werkzeuge—email info@metav-werkzeuge.com or call +49 2822 7131930 for local supply from Emmerich.

Technical data

• SKU: T492TM
• Manufacturer: Teknik Makina
• Product name: Eckmesserkopf
• For inserts: for LNGX 1307 Indexable Inserts
• Compatible insert manufacturer: Walter

Facts

• Diameter: 63 mm
• Overall length: 45 mm
• Mounting diameter: 22 mm
• Weight: 0.56 kg
• Cutting angle: 90°
• Cutting edges: 6

Special features

• Torx screw: M4x10
• Torx key size: T15
• Compatible inserts: LNGX 1307
• Application: Corner turning with indexable inserts

FAQ

Which indexable inserts fit this turning head?

The Eckmesserkopf T492TM is designed for LNGX 1307 indexable inserts; these inserts are compatible with the clamping geometry and ensure correct seating and performance.

What fastening tools are required for insert changes?

Insert clamping and release use a Torx M4x10 screw tightened with a T15 key to guarantee secure fixation and repeatable seating.

Will the head fit small toolposts and tight setups?

The compact Ø63 mm body with a 22 mm mounting diameter and 45 mm overall length is intended for installations with restricted clearance while maintaining rigidity.

How many cutting edges are available before replacement?

The head presents six cutting edges via the insert system, extending time between indexings and reducing tooling change frequency.

Is the Eckmesserkopf T492TM suitable for general profiling and finishing?

Yes — the combination of a fixed 90° cutting angle and indexable insert use makes the head well suited to both profiling and finishing passes where consistent geometry is required.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; eMail: info@metav-werkzeuge.com