50mm Corner Tool Head For WNEX 0806 Indexable Inserts Internal Coolant, 90° - Teknik Makina

Take advantage of a compact tooling solution that combines rigidity and effective cooling for consistent results in turning operations; the 50 mm diameter head with a 90° cutting angle and internal coolant reduces tool chatter and extends insert life — order directly via Metav Werkzeuge or consult our specialists for fine‑tuning.

Eckmesserkopf corner tool head by Teknik Makina — 50 mm, internal coolant

Eckmesserkopf is a compact corner tool head designed for precise turning and shoulder operations with WNEX 0806 indexable inserts

• 50 mm diameter cutting head
• Internal coolant for improved chip evacuation
• Compatible with WNEX 0806 indexable inserts
• Torx T15 screw M4x10 retention

Stable cutting geometry for reliable surface finish

The robust 50 mm diameter body delivers rigidity where it matters, reducing vibration during shoulder and facing cuts. A defined 90° cutting angle creates consistent contact geometry, which in turn improves repeatability and surface quality on both short and medium‑length overhangs. For workshops aiming to tighten tolerances, the compact head form provides a predictable cutting behaviour and helps maintain machine uptime through fewer reworks.

Controlled cooling for longer insert life and cleaner chips

Built‑in internal coolant channels direct coolant to the cutting zone, improving heat dissipation and chip control during continuous or interrupted cuts. This cooling strategy lowers thermal load on the insert edges and supports longer tool life, especially when machining challenging materials. Retention is secured via a Torx T15 screw (M4x10), ensuring consistent clamping torque and simple serviceability during index changes.

Proven compatibility and flexible tooling options

Designed for WNEX 0806 indexable inserts and compatible with YG‑1 inserts, the head simplifies tooling selection and replacement cycles. The 40 mm overall length keeps the cutting point close to the holder body for increased stiffness, while the unit’s modest mass (0.285 kg) makes it suitable for a broad range of lathes and turret configurations. Support for five cutting edges provides efficient use of insert geometry before replacement is required.

Practical workshop benefits and application focus

This corner tool head suits production and maintenance environments where repeatable shoulder cuts and accurate facing are required. The combination of a compact form, targeted coolant delivery and secure fastenings reduces cycle‑to‑cycle variation and supports higher first‑pass yields. For operations that value predictable tool behaviour and straightforward insert management, the component integrates smoothly into established tooling systems and procedure sheets.

Discuss specification details with Metav Werkzeuge to match this Teknik Makina corner tool head to the application requirements — contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for tailored advice and ordering support.

Technical Data

• Article number: T771-1TM
• Label: 50mm corner tool head WNEX 0806 L40mm with internal coolant
• Product type: Corner tool head
• Brand: Teknik Makina

Facts

• Diameter: 50 mm
• Overall length: 40 mm
• Weight: 0.285 kg
• Number of cutting edges: 5
• Cutting angle: 90°

Special features

• Internal coolant
• Compatible with WNEX 0806 indexable inserts
• Compatible insert manufacturer: YG-1
• Torx screw: M4x10 (Torx T15)

FAQ

What insert standard does this head accept? The corner tool head accepts WNEX 0806 indexable inserts; it is also compatible with inserts from YG‑1, allowing straightforward procurement of replacement edges.

How does the internal coolant improve performance? Internal coolant delivers fluid directly to the cutting zone, which helps to reduce heat at the edge, improve chip evacuation and extend insert life under continuous cutting.

Which screw and key are required for insert clamping? Insert retention uses a Torx T15 screw (M4x10); a T15 Torx key is recommended for correct clamping torque and repeatable seating.

Is the head suitable for long overhangs? The compact 40 mm overall length and 50 mm body diameter favour stiffness and stability; for extended overhangs, review machine and workpiece conditions to ensure acceptable deflection limits.

Can this tool head be used for finishing and semi‑finishing operations? Yes — the defined 90° cutting angle and rigid design make the head suitable for both semi‑finishing and finishing when matched with the appropriate insert grade.

Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com