63mm Face Milling Head for ONMU 0505 Indexable Inserts W45mm With Internal Cooling, 45° Cutting Angle - Teknik Makina

Combining a 63 mm cutting diameter with internal coolant and compatibility for ONMU 0505 indexable inserts, this face mill head delivers steady material removal and consistent surface quality; order directly via Metav Werkzeuge or consult the technical team for application-specific guidance.

Face mill head for ONMU 0505 indexable inserts — 63 mm, internal coolant (Teknik Makina)

The face mill head provides efficient facing with ONMU 0505 indexable inserts, designed for secure insert clamping and improved chip control in standard production environments.

• 63 mm diameter for broad facing
• Internal coolant for improved chip evacuation
• 6 cutting edges for high productivity
• Compatible with ISCAR ONMU 0505 inserts

Increased throughput through optimised geometry

With a 63 mm diameter and 6 cutting edges, this milling cutter head is engineered to raise metal removal rates while maintaining stability. The 45° cutting angle reduces cutting forces and spreads wear across the inserts, which helps preserve tool life and reduces the frequency of index changes. For shops focused on repeatable productivity, the arrangement of cutting edges and the cutter’s rigid mounting contribute to a predictable cycle time and consistent surface finish, translating into measurable process efficiency.

Coolant-fed design for thermal control and chip evacuation

The integrated internal coolant channel directs fluid close to the cutting zone, reducing heat generation at the edge and improving chip breakage. This results in lower thermal load on the inserts and a reduced risk of built-up edge, which in turn supports longer insert life and better component quality. The use of a coolant-fed head also simplifies coolant management compared with external-application setups, improving process reliability in wet machining operations and enhancing repeatability across batches.

Simple setup and proven compatibility for straightforward integration

Configured for ONMU 0505 indexable inserts from ISCAR and secured with M5x12 Torx screws (Torx key T20), the cutter head supports rapid insert changes and reliable clamping. The compact overall length of 45 mm and a mass of 0.652 kg make handling and tool change ergonomically manageable on most toolholders. Supplied as a ready-to-fit milling head, this solution eases retrofitting into established tool chains and helps maintain uptime by keeping changeover time low. The unit is supplied under Teknik Makina designation T794-1TM, enabling clear identification for spares and inventory control.

For application advice or to request the Teknik Makina face mill head T794-1TM with internal coolant, contact Metav Werkzeuge for tailored guidance and supply from Emmerich — info@metav-werkzeuge.com or +49 2822 7131930

Technical Data

• SKU: T794-1TM
• Manufacturer: Teknik Makina
• Product type: Face mill head
• Suitable for inserts: ONMU 0505
• Compatible insert brand: ISCAR
• Torx screw: M5x12
• Torx key: T20

Facts

• Diameter: 63 mm
• Overall length: 45 mm
• Weight: 0.652 kg
• Cutting edges: 6
• Cutting angle: 45°
• Internal coolant: yes

Special features

• Internal coolant channel
• Indexable inserts: ONMU 0505
• Secured with M5x12 Torx screws
• Compact design for easy integration

FAQ

Which inserts are compatible with this milling head?
The face mill head accepts ONMU 0505 indexable inserts and is listed as compatible with ISCAR inserts for straightforward procurement and replacement.

Does the head support coolant-through operation?
Yes, the head features internal coolant channels designed to deliver coolant directly to the cutting zone to aid chip control and thermal management.

What screw and key are required for insert mounting?
Insert clamping uses M5x12 Torx screws; a T20 Torx key is specified for secure and repeatable fastening of the inserts.

Is this head suitable for retrofit into existing toolholders?
The compact overall length (45 mm) and standard mounting form factor facilitate integration into many common toolholder systems; reference the designation T794-1TM for compatibility checks.

How many cutting edges are available per cutter head?
The head is equipped with six cutting edges, enabling efficient facing cycles and reduced changeover frequency.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com