80mm Corner Tool Head for XNKT 0805 Indexable Inserts L50mm With Internal Coolant - Teknik Makina

Reliable machining results through the combination of an 80 mm tool diameter, internal coolant and compatibility with XNKT 0805 indexable inserts; ideal for consistent shoulder and corner operations. Order the tool via Metav Werkzeuge or consult their specialists for application recommendations.

Corner milling head for XNKT 0805 indexable inserts — 80 mm, internal coolant (Teknik Makina)

A corner milling head designed for precision shoulder and face machining, optimised for XNKT 0805 indexable inserts and industrial production environments.

• 80 mm tool diameter, stable runout
• Integrated internal coolant
• Compatible with Korloy XNKT 0805 inserts
• Torx T15 assembly with M4x10 screws

High-performance cutting for predictable cycle times

The Corner milling head (SKU T906-1TM) delivers stable cutting performance thanks to its 80 mm diameter and seven cutting edges, which together support efficient material removal in shoulder and fillet operations. The internal coolant supply reduces thermal load at the cutting zone, slowing tool wear and helping to maintain dimensional consistency over longer runs. A defined 90° cutting angle provides reliable contact geometry for square shoulders, while the compatibility with XNKT 0805 inserts ensures a wide choice of grades and coatings for specific materials. This configuration is aimed at improving machining stability and lowering unplanned stoppages through predictable tool life.

Compact, serviceable design that speeds setup

With an overall length of 50 mm and a measured mass of 1.015 kg, the tool head combines rigidity with a compact footprint that eases toolchanger access and magazine space planning. Assembly uses M4x10 fastening hardware with a Torx T15 drive, simplifying repeatable clamping and maintenance tasks. The tool geometry and balanced mass distribution reduce vibration, contributing to better surface finish and longer insert life. Compatibility with Korloy XNKT 0805 inserts also streamlines procurement and inventory management in workshops that already use that insert family.

Industrial readiness and straightforward maintenance

Built for routine workshop use, the head’s internal coolant routing supports both wet cutting and coolant‑through strategies, improving chip evacuation and cooling efficiency. The indexable insert system reduces overall tooling costs by allowing rapid insert changes without regrinding or reconditioning the head. Routine maintenance is limited to insert changes and periodic inspection of the coolant channels and fasteners; the Torx T15 drive ensures secure assembly and straightforward service intervals. Supplied by Teknik Makina and distributed via Metav Werkzeuge, the tool head is intended to integrate into established production processes with minimal adaptation.

For application-specific advice or to request the T906-1TM corner milling head from Teknik Makina, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930

Technical data

• SKU: T906-1TM
• Manufacturer: Teknik Makina
• Product type: Corner milling head
• Label: 80 mm corner milling head XNKT 0805 L50 mm with internal coolant
• ECLASS: 21181015
• Diameter: 80 mm
• Overall length: 50 mm
• Weight: 1.015 kg
• Internal coolant: Yes
• Compatible inserts: XNKT 0805 (Korloy)
• Cutting edges: 7
• Cutting angle: 90°
• Screw type: M4x10 Torx T15
• UID: T906-1TM

Facts

• Diameter: 80 mm
• Length: 50 mm
• Weight: 1.015 kg
• Cutting edges: 7
• Cutting angle: 90°
• Screw size: M4x10

Special features

• Internal coolant
• Compatibility with Korloy XNKT 0805 inserts
• Torx T15 assembly
• Indexable insert system
• Robust 80 mm tool diameter

FAQ

Is this tool compatible with Korloy XNKT 0805 inserts?
Yes. The corner milling head accepts XNKT 0805 indexable inserts and is listed as compatible with Korloy insert grades.

What operations is the head best suited for?
The head is optimised for shoulder milling, face work and corner relief tasks where a 90° cutting angle and a stable 80 mm diameter provide repeatable results.

How is coolant delivered to the cutting zone?
Coolant is supplied via an internal coolant channel within the head, improving cooling at the insert rake face and supporting chip evacuation.

What fastening hardware is required for assembly?
Assembly uses M4x10 screws with a Torx T15 drive for secure clamping and straightforward maintenance.

What is the product designation and supplier for ordering?
The tool is supplied as SKU T906-1TM from Teknik Makina and is available through Metav Werkzeuge.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com