50mm T-Slot Cutter CCMT 1204 Inserts 4-Flute 110mm, 32mm Shank - Teknik Makina

Efficient T-slot milling is achieved with the combination of a 50 mm cutting diameter and four cutting edges, delivering stable material removal and consistent groove geometry; the shaft Ø 32 mm ensures rigid clamping for repeatable results. Order the cutter directly via Metav Werkzeuge or consult our specialists for application support.

T-Nut Cutter TKC108TM – Indexable T-slot milling cutter, Ø 50 mm, Teknik Makina

The T-Nut Cutter TKC108TM provides precise T-slot machining with indexable CCMT 1204 inserts, designed for workshop and production milling tasks

• Ø 50 mm cutting diameter
• Compatible with CCMT 1204 inserts
• Shaft Ø 32 mm for rigid clamping
• Four cutting edges for balanced cutting

Increase throughput with reliable cutting geometry

The large Ø50 mm cutter body combined with four cutting edges permits steady chip removal and reduced vibration, which translates into shorter cycle times and improved surface quality on the machined slot. With support for indexable inserts the tool enables rapid insert changes, lowering downtime compared with brazed or monolithic cutters. The modular concept of insert-based cutters means maintenance is limited to replacing worn CCMT 1204 inserts and the securing screw, keeping production flowing while maintaining dimensional consistency across batches.

Fast set-up and secure clamping for repeatable results

A robust shaft Ø 32 mm provides secure clamping in standard toolholders, increasing torsional stability during high-feed operations. The cutter’s 110 mm overall length gives adequate reach for common T-slot depths without excessive overhang, while a cutting length of 50 mm offers sufficient engagement for profiling wider slots. Insert retention is handled by an M5x12 Torx screw, tightened with a T20 key, ensuring simple and reliable assembly. These design choices reduce set-up time and help achieve the same tool datum from one shift to the next.

Durable construction aimed at consistent production quality

The TKC108TM’s balance between body mass and cutting geometry supports consistent machining forces; the tool mass of 0.691 kg contributes to steady cutting dynamics and lowers chatter risk in many milling set-ups. The tool’s compatibility with widely available CCMT 1204 indexable inserts offers a cost-effective route to maintain sharp cutting edges: wear can be addressed by rotating or replacing individual inserts rather than changing the entire cutter. The combination of balanced cutting and replaceable inserts reduces scrap rates and supports a predictable production schedule.

Practical workshop guidance and application notes

For reliable results, verify holder compatibility with the shaft Ø 32 mm and ensure correct torque on the M5x12 Torx screw using a T20 key to secure each insert. Regular inspection of insert seating and the screw thread will prevent unplanned stoppages. For varied materials, select the appropriate CCMT grade to match hardness and cutting conditions; the indexable system makes grade swaps straightforward. If uncertainty remains about suitability for a specific task, technical advice is available through Metav Werkzeuge to assist with tool selection and process parameters.

For precise and dependable T-slot production request the Teknik Makina TKC108TM through Metav Werkzeuge or contact our consultants at Metav Werkzeuge for tailored machining advice

Technical Data

• Article number: TKC108TM
• Manufacturer: Teknik Makina
• Designation: T-Nut Cutter
• Compatible inserts: CCMT 1204
• Torx screw: M5x12
• Torx key: T20

Key Facts

• Cutting diameter: 50 mm
• Number of cutting edges: 4
• Shaft diameter: 32 mm
• Cutting length: 50 mm
• Cutting height: 20 mm
• Overall length: 110 mm
• Weight: 0.691 kg

Special features

• Indexable insert system
• Balanced four-edge geometry
• Secure insert fixation with Torx screw
• Designed for repeatable T-slot machining

FAQ

Which inserts fit this cutter?

The cutter accepts CCMT 1204 indexable inserts; the TKC108TM is configured for these standard carbide inserts to allow rapid replacement and varied cutting grades.

What shaft diameter does the tool require for clamping?

Clamping requires a holder compatible with a shaft Ø 32 mm, matching the cutter’s shaft for rigid and stable mounting.

How many cutting edges are provided and what is the benefit?

The tool has four cutting edges, providing balanced cutting forces and steady chip evacuation for consistent slot geometry.

What is the overall length and typical reach for the cutter?

Overall length is 110 mm, offering sufficient reach for common T-slot profiles while keeping overhang modest for stability.

Are special tools required to change the inserts?

Insert retention uses an M5x12 Torx screw secured with a T20 key; this standardised solution streamlines insert changes and reduces toolroom complexity.

Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com